scholarly journals Preparation and properties of (epoxy resin)/(nylon 6,6 oligomer) blends

2009 ◽  
Vol 3 (2) ◽  
pp. 111-115
Author(s):  
Jason Bragg ◽  
◽  
Alberto Alvarez-Castillo ◽  
Monica Trejo-Duran ◽  
Victor Castano ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Considerable Increase ◽  
Flexural Modulus ◽  
Strength Testing ◽  
Curing Agent ◽  
Maximum Increase ◽  
Maximum Value ◽  
Nylon 6,6

A series of polymer alloys based on different compositions of Nylon 6,6 oligomers (NYL66Oґs) and epoxy resin have been prepared. The oligomer was extracted from the waste residues of the industrial production of nylon 6,6 and was dissolved in the epoxy resin. The mixture was crosslinked at 333 K using dodecenylsuccinic anhydre (DDSA) as a curing agent. The tensile strength and flexural modulus were found to increase with the addition of NYLO66O up to a maximum value of 2 wt % oligomer content. Both, the tensile and impact strength show a maximum increase due to the addition of 35 wt % NYLO66O. The compressive strength testing revealed a considerable increase, up to 87 %, over that of the neat epoxy with the addition of 1 wt % NYLO66O. An interesting relationship between the mechanical properties and the developed morphology of the blends has been found.

scholarly journals PENGARUH PENAMBAHAN BENTONIT TERMODIFIKASI SEBAGAI PENGISI TERHADAP SIFAT MEKANIK DAN PENYERAPAN AIR KOMPOSIT EPOKSI

2017 ◽  
Vol 5 (4) ◽  
pp. 39-44
Author(s):  
Alvian ◽  
Kenrick ◽  
Iriany
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Absorption ◽  
Epoxy Resin ◽  
Cetyltrimethylammonium Bromide ◽  
Absorption Capacity ◽  
Modified Bentonite ◽  
Maximum Value ◽  
Ftir Characterization ◽  
Scaning Electron Microscopy

Research about the application of modified bentonite as filler in epoxy has been done for the purpose of getting the best composition of modified bentonite as filler at epoxy composite to obtain the best mechanical properties such as tensile strength, impact strength and the water absorption. In this research, epoxy resin mixed with bentonite which have been modified using cetyltrimethylammonium bromide (CTAB) surfactant with various concentrations of 0,05M, 0,1M, and 0,15M. Modified bentonite filler and TiO2 then mixed with epoxy resin with various concentration of 5%, 10%, 15%, and 20% of filler from the total mass of the composite and then the composite was produced with hand lay-up method. The result of FTIR characterization showed that the bond between matrix and the filler produced was only interfacial bonding. The result of the mechanical properties test indicated that 5% of filler composition with 0,1M of surfactant concentration obtained the maximum value of tensile strength and mechanical strength respectively 33,667 MPa and 12564,9 J/m2. The result of mechanical properties test was supported by analysis of Scaning Electron Microscopy (SEM). On the test of water absorption, the water absorption capacity increased along with the increased of filler composition.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Assessing the Flexural Properties of Epoxy Composites with Extremely Low Addition of Cellulose Nanofiber Content

2020 ◽  
Vol 10 (3) ◽  
pp. 1159 ◽  
Author(s):  
Yingmei Xie ◽  
Hiroki Kurita ◽  
Ryugo Ishigami ◽  
Fumio Narita
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Flexural Modulus ◽  
Strengthening Mechanism ◽  
Short Fiber ◽  
Cellulose Nanofiber ◽  
Resin Matrix ◽  
Element Analysis ◽  
Epoxy Resin Matrix ◽  
The Matrix

Epoxy resins are a widely used common polymer due to their excellent mechanical properties. On the other hand, cellulose nanofiber (CNF) is one of the new generation of fibers, and recent test results show that CNF reinforced polymers have high mechanical properties. It has also been reported that an extremely low CNF addition increases the mechanical properties of the matrix resin. In this study, we prepared extremely-low CNF (~1 wt.%) reinforced epoxy resin matrix (epoxy-CNF) composites, and tried to understand the strengthening mechanism of the epoxy-CNF composite through the three-point flexural test, finite element analysis (FEA), and discussion based on organic chemistry. The flexural modulus and strength were significantly increased by the extremely low CNF addition (less than 0.2 wt.%), although the theories for short-fiber-reinforced composites cannot explain the strengthening mechanism of the epoxy-CNF composite. Hence, we propose the possibility that CNF behaves as an auxiliary agent to enhance the structure of the epoxy molecule, and not as a reinforcing fiber in the epoxy resin matrix.

scholarly journals Preliminary Study on Mechanical Properties of 3D Printed Multimaterials ABS/PC Parts: Effect of Printing Parameters

2021 ◽  
Vol 32 (2) ◽  
pp. 87-104
Author(s):  
Pui-Voon Yap ◽  
Ming-Yeng Chan ◽  
Seong-Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flexural Modulus ◽  
Nozzle Diameter ◽  
Fused Deposition ◽  
Printing Parameters ◽  
Printing Speed

This research work highlights the mechanical properties of multi-material by fused deposition modelling (FDM). The specimens for tensile and flexural test have been printed using polycarbonate (PC) material at different combinations of printing parameters. The effects of varied printing speed, infill density and nozzle diameter on the mechanical properties of specimens have been investigated. Multi-material specimens were fabricated with acrylonitrile butadiene styrene (ABS) as the base material and PC as the reinforced material at the optimum printing parameter combination. The specimens were then subjected to mechanical testing to observe their tensile strength, Young’s modulus, percentage elongation, flexural strength and flexural modulus. The outcome of replacing half of ABS with PC to create a multi-material part has been examined. As demonstrated by the results, the optimum combination of printing parameters is 60 mm/s printing speed, 15% infill density and 0.8 mm nozzle diameter. The combination of ABS and PC materials as reinforcing material has improved the tensile strength (by 38.46%), Young’s modulus (by 23.40%), flexural strength (by 23.90%) and flexural modulus (by 37.33%) while reducing the ductility by 14.31% as compared to pure ABS. The results have been supported by data and graphs of the analysed specimens.

scholarly journals Effects of Irradiation by UV- Acceleration on Mechanical Properties of Polymer Blends (Polyester: Starch)

2018 ◽  
Vol 21 (1) ◽  
pp. 147 ◽  
Author(s):  
Sihama I. Salih ◽  
Qahtan A. Hamad ◽  
Safaa N. Abdul Jabbar ◽  
Najat H. Sabit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Polymer Blends ◽  
Modulus Of Elasticity ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Weight Ratio ◽  
Weight Fraction ◽  
Elongation Percentage

This work covers mixing of unsaturated polyester (un- polyester) with starch powders as polymer blends and study the effects of irradiation by UV-acceleration on mechanical properties of its. The unsaturated polyester was mixing by starch powders at particle size less than (45 µm) at selected weight fraction of (0, 0.5, 1, 1.5, 2, 2.5 and 3%). These properties involve ultimate tensile strength, modulus of elasticity, elongation percentage, flexural modulus, flexural strength, fracture toughness, impact strength and hardness. The results illustrate decrease in the ultimate tensile strength at and elongation percentage, while increasing modulus of elasticity, with increasing the weight ratio of starch powder to 3 % weight fraction, whereas the maximum value of hardness and flexural, impact properties happened at 1 % weight fraction for types of polymer blends.

Effect of Zr on the microstructures and mechanical properties of as-extruded Mg–2.3Zn–0.18Y–xZr alloys

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744001 ◽  
Author(s):  
Yufan Wang ◽  
Yingbo Zhang ◽  
Wei Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aging Treatment ◽  
Grain Refining ◽  
Maximum Increase ◽  
Microstructures And Mechanical Properties ◽  
Average Size ◽  
Precipitate Strengthening ◽  
Zr Alloys

The microstructures and mechanical properties of as-extruded Mg–2.3Zn–0.18Y–[Formula: see text]Zr ([Formula: see text] = 0.03, 0.06 and 0.13 at.%) alloys and aged Mg–2.3Zn–0.18Y–0.13Zr alloy were studied. The results revealed that the microstructures of as-extruded Mg–2.3Zn–0.18Y–[Formula: see text]Zr alloys are typical bimodal structures. The coarse [Formula: see text]-Mg grains are surrounded by fine dynamically recrystallized [Formula: see text]-Mg grains. The average size of [Formula: see text]-Mg grains decreases with increasing Zr content. Moreover, the addition of Zr (at.%) can improve the mechanical properties of alloy. The as-extruded Mg–2.3Zn–0.18Y–0.13Zr alloy has the best mechanical properties with ultimate tensile strength (UTS) and yield strength (YS) of 346 MPa and 292 MPa, respectively, and an elongation of 26.7%, which can be attributed to the grain refining effect and precipitate strengthening. The UTS and elongation of Mg–2.3Zn–0.18Y–0.13Zr alloy changed slightly after aging treatment, but the YS increases remarkably, with the maximum increase of 30 MPa. The fracture surfaces of all alloys consist of many tearing ridges and dimples.

HIGH TECHNIQUE FOR T-PEEL STRENGTH ENHANCEMENT OF Al/AFRP HYBRID COMPOSITE

2006 ◽  
Vol 20 (25n27) ◽  
pp. 4273-4278
Author(s):  
CHEOL-WOONG KIM ◽  
DONG-JOON OH
Keyword(s):  
Tensile Strength ◽  
Epoxy Resin ◽  
Hybrid Composite ◽  
Equivalence Ratio ◽  
Peel Strength ◽  
Aramid Fiber ◽  
Curing Agent ◽  
Mixture Ratio ◽  
Resin Mixture ◽  
Resin Curing

The interlaminar peel strength of Al / AFRP (Aluminum alloy/Aramid Fiber Reinforced Plastic) hybrid composite is affected by the adhesive strength between the Al alloy layer and the aramid fiber layer. The study of the tensile strength and the T-peel strength of the Al / AFRP should be accomplished first. Therefore, this study focused on the effect of the resin mixture ratio as the Al / AFRP on the tensile strength and T-peel strength. In conclusions, the resin mixture ratio by equivalence ratio of 〈epoxy resin : curing agent〉 equal to 〈1:1〉 of Al / AFRP -I and the resin mixture ratio by equivalence ratio of 〈epoxy resin : curing agent : accelerator〉 equal to 〈1:1:0.2〉 of Al / AFRP -II showed the highest ultimate tensile strength. After the T-peel test, it is found that the T-peel strength of Al / AFRP -II is approximately 1.5 times higher than that of Al / AFRP -I. Reviewing the characteristics of the tensile and T-peel strengths, the resin mixture ratio 〈1:1:0.2〉 of Al / AFRP -II showed the highest tensile strength and T-peel strength.

Mechanical Properties and Microstructure of Aramid/Al2O3/Epoxy Resin Laminated Composites

2008 ◽  
Vol 55-57 ◽  
pp. 389-392
Author(s):  
Supreyak Kumfu ◽  
Wim Nhuapeng ◽  
Wandee Thamjaree ◽  
Tawee Tunkasiri
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Laminated Composites ◽  
Scratch Resistance ◽  
Resin Matrix ◽  
Sem Images ◽  
Laminate Composites ◽  
Al2o3 Powder ◽  
Casting Technique

Aramid/Al2O3/epoxy resin laminated composites were fabricated using ultrasonic mixing and casting technique. This novo material could be exhibited to the ideal mechanical properties such as high tensile strength, hardness, flexural strength and lightweight which may be used to replace metal parts in vehicles. Moreover, Al2O3 powder was mixed to epoxy resin to improve the scratch resistance. To improve the bending force and interaction between Al2O3 powder phase and epoxy resin phase, the ultrasonic mixing was used for fabricating these laminate composites. The physicals and mechanical properties such as density, hardness, impact test, wear resistance and tensile strength of the composites samples were investigated. It was found that the amounts of percent by volume of the Al2O3 have affected the properties of the laminated composites. Furthermore, microstructures of specimens were also investigated by scanning electron microscope (SEM). From the results, SEM images showed good distribution and adhesion between reinforced phase and epoxy resin matrix phase.

Curing study and evaluation of epoxy resin with amine functional chloroaniline acetaldehyde condensate

2015 ◽  
Vol 44 (1) ◽  
pp. 19-25
Author(s):  
T. Maity ◽  
B.C. Samanta
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Epoxy Resin ◽  
Ph Value ◽  
Kinetic Studies ◽  
Diglycidyl Ether ◽  
Curing Agent ◽  
Scanning Calorimetry ◽  
Content Type ◽  
Curing Reaction

Purpose – The purpose of this paper was to check effectiveness of amine functional chloroaniline acetaldehyde condensate (AFCAC) as a new curing agent for diglycidyl ether of bisphenol A (DGEBA) resin. For this purpose, first AFCAC was synthesised, characterised and then curing reaction was carried out. Design/methodology/approach – Equimolecular mixture of AFCAC and DGEBA was subjected to curing reaction, and the reaction was followed by differential scanning calorimetry (DSC) analysis. The kinetic studies of this curing reaction were also carried out from those DSC exotherms. The mechanical properties, dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) of cured epoxy were also reported. Findings – DSC results reflected the effective first order curing reaction of AFCAC with epoxy resin. Mechanical properties reflected appreciable rigidity of AFCAC cured epoxy matrix and TGA showed that the cured epoxy networks were thermally stable up to around 297°C. Research limitations/implications – The curing agent AFCAC was synthesised by using chloroaniline and acetaldehyde in acid medium. There are some limitations for this procedure. The synthetic procedure is pH dependent. So reaction cannot be done at any pH value. The reaction must also be carried out at room temperature without any heating. To obtain low molecular weight curing agent, chloroaniline and acetaldehyde cannot be taken in equimolecular ratio because the equimolecular mixture of them produces high molecular weight condensate. This was shown in our previous publication. Some implications are also there. By changing amine and aldehyde other curing agents could be synthesised and the curing efficiency of those for epoxy resin could also be studied. Originality/value – Experimental results revealed the greater suitability of AFCAC as curing agent for DGEBA resin and novelty of AFCAC cured matrix in the field of protective coating, casting, adhesives, etc.

Effect of reactive and non-reactive diluents on thermal and mechanical properties of epoxy resin

2017 ◽  
Vol 30 (10) ◽  
pp. 1159-1168 ◽  
Author(s):  
Animesh Sinha ◽  
Nazrul Islam Khan ◽  
Subhankar Das ◽  
Jiawei Zhang ◽  
Sudipta Halder
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Polyethylene Glycol ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Thermal And Mechanical Properties ◽  
Minor Variation ◽  
Reactive Diluents

The effect of reactive (polyethylene glycol) and non-reactive (toluene) diluents on thermal and mechanical properties (tensile strength, hardness and fracture toughness) of diglycidyl ether of bisphenol A epoxy resin (cured by triethylenetetramine) was investigated. The thermal stability and mechanical properties of the epoxy resin modified with reactive and non-reactive diluents at different wt% were investigated using thermo-gravimetric analyser, tensile test, hardness test and single-edge-notched bend test. A minor variation in thermal stability was observed for epoxy resin after addition of polyethylene glycol and toluene at 0.5 wt%; however, further addition of reactive and non-reactive diluents diminished the thermal stability. The addition of 10 wt% of polyethylene glycol in epoxy resin significantly enhances the tensile strength (∼12%), hardness (∼14%) and fracture toughness (∼24%) when compared to that of neat epoxy resin. In contrast, major drop in mechanical performance was observed after addition of toluene in epoxy. Furthermore, fracture surfaces were investigated under field emission scanning electron microscope to elucidate the failure mechanism.

Sign in / Sign up

Export Citation Format

Share Document