scholarly journals Impact Tests of UHSS Steel Welded Joints Using the Drop - Tower Impact Drop Method

2019 ◽  
Vol 19 (3) ◽  
pp. 19-31
Author(s):  
J. Dorożyński ◽  
J. Nowacki ◽  
A. Sajek
Keyword(s):  
Impact Strength ◽  
Welded Joints ◽  
Impact Test ◽  
Gma Welding ◽  
High Strength ◽  
Test Method ◽  
Drop Tower ◽  
Current Application ◽  
Impact Tests ◽  
The Impact

AbstractThe article characterizes the impact test method using Drop-Tower Impact Test with the registration of the value of force and energy of breaking. Based on sources, the possibilities and scope of the current application of this method were determined and the current state of knowledge on the results of these tests was reviewed. In order to determine the possibility of using the method in impact tests of high strength steel joints, investigations of hybrid PTA - GMA welding conditions on impact strength of joints of MART S1300QL steel were carried out. In particular, the influence of t8/5 cooling time on the impact strength of welded joints by the Drop - Tower Impact Test method was determined. It has been shown that the use of dropping machine with computer-based registration of breaking force and energy values was possible in the case of impact strength testing of UHSS welded joints and enabled precise analysis of the energy distribution dynamics absorbed by the tested.

Расчетные методы оценки ударной вязкости сварных элементов с трещинами

2020 ◽  
Vol 44 (3) ◽  
pp. 22-36
Author(s):  
Keyword(s):  
Stress Intensity ◽  
Impact Strength ◽  
Welded Joints ◽  
Development Process ◽  
Welded Joint ◽  
Operating Temperature ◽  
Crack Development ◽  
Heterogeneous Structure ◽  
Critical Crack Length ◽  
The Impact

Практика показывает, что для сварных конструкций, эксплуатируемых в условиях Крайнего Севера необходимо уделять внимание работоспособности сварных соединений при низких температурах. Металл сварных соединений в процессе воздействия обработки изменяет свои свойства, снижается ударная вязкость, образуется гетерогенная структура с большой степенью разнозернистости. Чтобы оценивать и иметь возможность правильно контролировать термическое воздействие и последствия сварочного процесса, требуется решить задачу аналитического определения ударной вязкости для всех зон сварного соединения. В настоящей статье представлен инженерный метод оценки ударной вязкости, применимый для любой зоны сварного соединения, в которой имеется острый или особый концентратор напряжений – трещина. Разработанный аналитический метод расчета ударной вязкости отражает качественную и количественную картину взаимосвязи структурно-механических характеристик и работы развития трещины в диапазоне температур 77…300 К. Предложенная схематизация зависимости критического коэффициента интенсивности напряжений от температуры позволила найти коэффициенты, характеризующие свойства материала, и выполнить расчеты изменения предела текучести и предела прочности от температуры эксплуатации. Построены графики зависимости работы развития трещины от температуры эксплуатации для сталей 15ГС и 17ГС, сравнение которых с экспериментальными данными показывает удовлетворительное согласование. Найдено, что при напряжениях предела выносливости отношение работы развития трещины к критической длине трещины постоянно, не зависит от температуры и для сталей 15ГС и 17ГС равно около 10. Ключевые слова: ударная вязкость, работа разрушения, коэффициент интенсивности напряжений, трещина, феррито-перлитная сталь, зона термического влияния. For welded structures under operation in the Far North, attention must be paid to the performance of welded joints at low temperatures. The properties of metal of welded joints are changed in the process of treatment, its toughness decreases, and a heterogeneous structure with a large range of different grain sizes is formed. In order to evaluate and be able to correctly control the thermal effect and the consequences of the welding process, it is necessary to solve the problem of analytical determination of impact strength for all zones of the welded joint. The paper presents an engineering method for evaluation of the impact strength applicable to any area of the welded joint in which there is a sharp or super sharp stress concentrator – a crack. The developed analytical method for calculating the impact strength reflects a qualitative and quantitative codependency of structural and mechanical characteristics and the process of crack development in the temperature range of 77–300 K. The proposed schematization of dependence of the critical coefficient of stress intensity on the temperature made it possible to find coefficients characterizing the properties of the material and to perform calculations of changes in yield strength and tensile strength on operating temperature. Graphs of the crack development process dependency on the operating temperature for 15ГС and 17ГС steels were constructed, and their comparison with experimental data displays satisfactory agreement. It was found that at endurance limit stresses, the ratio of the crack development process to the critical crack length is constant, non-dependent on temperature, and is equal to 10 for 15ГС and 17ГС steels. Keywords: impact strength, fracture work, stress intensity factor, crack, ferrite-pearlite steel, heat affected zone, steel tempering.

scholarly journals Impact resistance of steel materials to ballistic ejecta and shelter development using steel deck plates

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Kohei Tateyama ◽  
Shino Naruke ◽  
Hisashi Sasaki ◽  
Shinichi Torigata ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Test ◽  
Impact Resistance ◽  
Protective Layer ◽  
High Strength ◽  
Steel Plates ◽  
Corrugated Plates ◽  
Shelter Construction ◽  
The Impact ◽  
Ballistic Ejecta

AbstractThe destruction caused by ballistic ejecta from the phreatic eruptions of Mt. Ontake in 2014 and Mt. Kusatsu-Shirane (Mt. Moto-Shirane) in 2018 in Japan, which resulted in numerous casualties, highlighted the need for better evacuation facilities. In response, some mountain huts were reinforced with aramid fabric to convert them into shelters. However, a number of decisions must be made when working to increase the number of shelters, which depend on the location where they are to be built. In this study, we propose a method of using high-strength steel to reinforce wooden buildings for use as shelters. More specifically, assuming that ballistic ejecta has an impact energy of 9 kJ or more, as in previous studies, we developed a method that utilizes SUS304 and SS400 unprocessed steel plates based on existing impact test data. We found that SUS304 is particularly suitable for use as a reinforcing material because it has excellent impact energy absorption characteristics due to its high ductility as well as excellent corrosion resistance. With the aim of increasing the structural strength of steel shelters, we also conducted an impact test on a shelter fabricated from SS400 deck plates (i.e., steel with improved flexural strength provided by work-hardened trapezoidal corrugated plates). The results show that the shelter could withstand impact with an energy of 13.5 kJ (2.66 kg of simulated ballistic ejecta at 101 m/s on impact). In addition, from the result of the impact test using the roof-simulating structure, it was confirmed the impact absorption energy is further increased when artificial pumice as an additional protective layer is installed on this structure. Observations of the shelter after the impact test show that there is still some allowance for deformation caused by projectile impact, which means that the proposed steel shelter holds promise, not only structurally, but also from the aspects of transportation and assembly. Hence, the usefulness of shelters that use steel was shown experimentally. However, shelter construction should be suitable for the target environment.

Experimental Determination of Dynamic Characteristics of a Full Size Gas Turbine Tilting-Pad Journal Bearing by an Impact Test Method

1991 ◽  
Author(s):  
S. H. Chan ◽  
M. F. White
Keyword(s):  
Gas Turbine ◽  
Impact Test ◽  
Journal Bearing ◽  
Estimation Procedure ◽  
Response Spectra ◽  
Test Method ◽  
Full Size ◽  
Tilting Pad ◽  
Tilting Pad Journal Bearing ◽  
The Impact

Abstract Measurements have been taken on an experimental rotor-bearing test rig which consists of a full size gas turbine shaft supported by two five-pad tilting-pad journal bearings. The impact test method was applied by exciting one end of the shaft in-situ by means of a hammer blow. Impact forces and response displacements were collected and analysed with suitable corrections for runout effect. Averaged frequency response spectra thus obtained were used in a parameter estimation procedure to calculate the dynamic coefficients of the tested tilting-pad journal bearing. An analytical single degree-of-freedom model was employed and one of the input parameters in the mechanical model, the effective mass, was found to significantly influence the estimated results. The measured stiffness and damping coefficients are compared with results predicted by a bearing design program. Possible sources of discrepancies between experimental and theoretical results are discussed.

scholarly journals KARAKTERISTIK SIFAT MEKANIS ANTARA TIGA PRODUK MANUFAKTUR ELEKTRODA E6013

2019 ◽  
Vol 3 (1) ◽  
pp. 40-45
Author(s):  
Basori Basori ◽  
Ferry Budhi Susetyo
Keyword(s):  
Impact Strength ◽  
Test Specimen ◽  
Impact Test ◽  
Surface Hardness ◽  
Welding Process ◽  
Hardness Test ◽  
Bottom Plate ◽  
Weld Deposit ◽  
Welding Electrode ◽  
The Impact

The type of electrode used in the SMAW process has many types, such as E 6010, E 6011, E 6012, E 6013, E 6020, E6027. In this case the type E 6013 is the most widely used. Certainly the type E 6013 is produced by different manufacturers as well. From penelurusan researchers of this type have different prices in accordance with companies that sell it. For that reason researchers are interested to compare the three manufacturing outputs for the type E 6013 in terms of its mechanical properties. Making a specimen welding electrode cut material to be used. then sandpaper the material that has been cut so that no remaining pieces are still attached. The next step to do the welding process with three types of E6013 elekroda. The welding is carried out until it reaches the layer layer 10 mm thickness, then the bottom plate is discarded and the weld deposit deposits only The impact strength and surface hardness value are inversely proportional. For the impact test, the E1 electrode sample specimen has the highest impact strength value and the E3 electrode sample specimen has the lowest impact strength value. While on the hardness test specimen E3 electrode sample has the highest hardness value and sample specimen E1 electrode has the lowest hardness value. This can prove that the harder the object is the more brittle the object.

scholarly journals The Effect of Crystallinity on the Toughness of Cast Polyamide 6 Rods with Different Diameters

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 293
Author(s):  
Miklós Odrobina ◽  
Tamás Deák ◽  
László Székely ◽  
Tamás Mankovits ◽  
Róbert Zsolt Keresztes ◽  
...  
Keyword(s):  
Impact Strength ◽  
Impact Test ◽  
Charpy Impact ◽  
Polyamide 6 ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Tensile Impact ◽  
Different Diameters ◽  
The Impact ◽  
The Degree Of Crystallinity

The present paper concentrates on the toughness and the degree of crystallinity of the magnesium-catalyzed polyamide 6 rods cast in different diametres, which are commonly used for gear manufacturing. Its toughness cannot be regarded as a constant feature due to the casting technology. The mechanical properties of the semi-finished products are sensitive to the manufactured dimension, e.g., cast diameter, which are investigated by the Charpy impact test and tensile impact test. It is generally accepted that the impact strength and tensile-impact strength correlate with the degree of crystallinity beside many other material’s feature. Crystallinity is evaluated by Differential Scanning Calorimetry. The aim of this study is to determine the relationship between toughness and crystallinity of the magnesium-catalyzed cast PA6 rods with different diameters. For the research cast rods between 40 and 300 mm diameter were selected in seven-dimensional steps. Based on the results, it was found that the toughness depends strongly on the diameter size. Furthermore, it is proved that the crystallinity explains 62.3% of the variation of the Charpy’s impact strengths, while the tensile impact method was not suitable to detect the difference between the test samples.

Impact Strength of High Density Solid-State Microcellular Polycarbonate Foams

2000 ◽  
Vol 123 (2) ◽  
pp. 229-233 ◽  
Author(s):  
Chris Barlow ◽  
Vipin Kumar ◽  
Brian Flinn ◽  
Rajendra K. Bordia ◽  
John Weller
Keyword(s):  
Solid State ◽  
Impact Strength ◽  
Cell Size ◽  
High Density ◽  
Gas Content ◽  
Impact Behavior ◽  
Strong Function ◽  
Impact Tests ◽  
Izod Impact ◽  
The Impact

The effect of density (relative densities 0.33 to 0.90) on the impact behavior of microcellular polycarbonate (PC) was investigated. Cell size and foaming gas content were also considered. Flexed-beam Izod impact tests were conducted and the impact strength of these foams appears to be a strong function of both density and cell size. The impact strength was observed to improve over the unprocessed polycarbonate’s impact strength for foams with relative densities of 60 percent and above. In terms of cell size, the impact strength increased with increasing cell size at a given density.

A smart prediction tool for estimating the impact strength of welded joints prepared by vibratory welding process

2016 ◽  
Vol 231 (2) ◽  
pp. 343-346 ◽  
Author(s):  
P Govinda Rao ◽  
P Srinivasa Rao ◽  
A Gopala Krishna
Keyword(s):  
Impact Strength ◽  
Welded Joints ◽  
Welding Process ◽  
Input Voltage ◽  
Grain Structure ◽  
Generalized Regression Neural Network ◽  
Prediction Tool ◽  
Fine Grain ◽  
Vibration Parameters ◽  
The Impact

Previous researches have been devoted to development of vibratory setup for inducing mechanical vibrations into the weld pool during welding process. The designed vibratory setup produces the required frequency with suitable amplitude and acceleration in terms of voltages. This helps in producing uniform and fine grain structure in the welded joints which results in an improvement in the mechanical properties of the weld pieces at heat affected zone. This paper presents the development of a smart prediction tool by implementing generalized regression neural network to establish a relation between vibration parameters such as input voltage to the vibromotor, time of vibration and impact strength of vibratory weld joints. In order to validate the feasibility of the developed prediction tool, a comparison is made with the experimental results.

New Emerging Al7075 Based Hybrid Nanocomposite for Automotive Applications: A Sustainability Approach

2020 ◽  
Vol 856 ◽  
pp. 29-35
Author(s):  
Sweety Mahanta ◽  
M. Chandrasekaran ◽  
Sutanu Samanta
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Hybrid Composites ◽  
High Strength ◽  
Stir Casting ◽  
Automotive Application ◽  
Percentage Increase ◽  
Casting Technique ◽  
Ultrasonic Assisted Stir Casting ◽  
The Impact

Aluminium matrix composites (AMCs) have emerged as the substitute for the monolithic (unreinforced) materials over the past few decades. The applications of AMCs are common in automotive, aerospace, defence and biomedical sectors due to its lower weight, high strength, high resistance against corrosion and high thermal and electrical conductivity. In this work, it is aimed fabricate a new class Al 7075 based hybrid composites reinforcing with nanoparticulates suitable for automotive application. Al7075 reinforced with fixed quantity of boron carbide (B4C) (1.5 wt.%) and varying wt % of flyash (0.5 wt.%, 1.0 wt.%, 1.5 wt.%) is fabricated using ultrasonic-assisted stir casting technique. Physical and mechanical characterization such as density, porosity, micro hardness, tensile strength and impact strength were estimated for three different compositions. The tensile strength and percentage increase in hardness value of the nanocomposite Al7075-B4C (1.5 wt. %)-flyash (0.5 wt. %): HNC3 found maximum as 294 MPa and 32.93%. In comparison with Al7075 alloy the impact strength of HNC3 shows the highest percentage of 9.31% respectively.

Relationship Between Charpy V-Notch Impact Value and Fracture Mechanics Toughness: Added Value of Finite Element Analysis and Instrumented Impact Tests

2011 ◽  
Author(s):  
Philippe Thibaux ◽  
Filip Van den Abeele ◽  
Philippe Burlot
Keyword(s):  
Finite Element ◽  
Master Curve ◽  
Impact Test ◽  
Crack Arrest ◽  
Smooth Transition ◽  
Unstable Crack ◽  
Impact Tests ◽  
The Difference ◽  
Energy Dissipated ◽  
The Impact

Each structure is designed with resistance versus the fracture, which requires the knowledge of the fracture resistance of the material. If no fracture mechanics data of the material is available, a KJC can be inferred from the master curve approach. The master curve approach relates a fracture toughness of 100 MPAm1/2 to the impact transition temperature T27J with a shift of 18°C. Although this relationship was successfully applied to a large number of experiments, some steels deviate significantly from the previous relationship, which can even lead to non-conservative design. In the present paper, instrumented impact tests (Charpy V-Notch CVN) and compact tensile (CT) tests were performed on two materials, one thermomechanically (TM-) rolled and one normalized steel. The difference between T0 and T27J was found to be different for these materials. Furthermore, the normalized steel exhibits a smooth transition from brittle to ductile behaviour, while the TM-rolled material shows a very steep transition. Extra information is gained by combining the instrumentation of the impact test and the finite element simulations of both the CT and impact tests. From the instrumented tests, it is also possible to determine the load at unstable crack propagation, the amount of energy dissipated at that moment, the load at crack arrest and the energy dissipated after crack arrest. From the finite element simulation, one learns about the constraints ahead of the crack tip for both configurations. The investigation teaches us that the smooth transition of the normalized material is related to a high energy dissipated after crack arrest, while the TM-rolled material has a much lower crack arrest load. The difference between T0 and T27J is then discussed by decomposing the total energy in the impact test between crack initiation, propagation and arrest. It is compared with KJC, which determines the toughness at unstable crack propagation, by reviewing the literature and local stress states computed from finite element.

Sign in / Sign up

Export Citation Format

Share Document