scholarly journals Testing and application of an integrated fluxgate sensor DRV425

2018 ◽  
Vol 69 (6) ◽  
pp. 418-421 ◽  
Author(s):  
Vojtech Petrucha ◽  
David Novotny

Abstract The article presents testing of a miniature fluxgate sensor developed and manufactured by Texas Instruments as well as an application of the sensor in a compact magnetic field probe with USB interface and LabView based software. Several basic properties of the sensor were evaluated and compared with the datasheet specifications. Offset stability measurements have indicated some possible problems for applications that require very high DC and low-frequency precision. Jumps in offset were present for some of the devices, frequency and duty of the jumps varying between individual pieces and with respect to the supply voltage. Magnetic probe for fast and handy measurements of DC and AC (up to 30 kHz) magnetic fields (up to ±1 mT) is also presented. The probe contains 24-bit analog to digital converter, microcontroller and high-speed USB interface which allows a live view of the signal in time and spectral charts. The probe proved to be very useful for the DRV425 debugging, application development, EMC measurements and magnetic field demonstrations activities.

2014 ◽  
pp. 27-33
Author(s):  
Mounir Bouhedda ◽  
Mokhtar Attari

The aim of this paper is to introduce a new architecture using Artificial Neural Networks (ANN) in designing a 6-bit nonlinear Analog to Digital Converter (ADC). A study was conducted to synthesise an optimal ANN in view to FPGA (Field Programmable Gate Array) implementation using Very High-speed Integrated Circuit Hardware Description Language (VHDL). Simulation and tests results are carried out to show the efficiency of the designed ANN.


2014 ◽  
Vol 13 (01) ◽  
pp. 1450003
Author(s):  
Bhanupriya Bhargava ◽  
Pradeep Kumar Sharma ◽  
Shyam Akashe

In this paper, a correlated double sampling (CDS) technique is proposed in the design of a delta sigma analog-to-digital converter (ADC). These CDS techniques are very effective for the compensation of the nonidealities in switched-capacitor (SC) circuits, such as charge injection, clock feed-through, operational amplifier (op-amp) input-referred offset and finite op-amp gain. An improved compensation scheme is proposed to attain continuous compensation of clock feed-through and offset in SC integrators. Both high-speed and low-power operation is achieved without compromising the accuracy requirement. Also this CDS delta sigma ADC is the most promising circuit for analog to digital converter because this circuit reduces noise due to drift and low frequency noise such as flicker noise and offset voltage and also boosts the gain performance of the amplifier. Further, the simulation results of this circuit are verified on using a "cadence virtuoso tool" using spectre at 45 nm technology with supply voltage 0.7 V.


2018 ◽  
Vol 28 (01) ◽  
pp. 1950018 ◽  
Author(s):  
Minh Tung Dam ◽  
Van Toan Nguyen ◽  
Jeong-Gun Lee

An all-digital multi-frequency clocking (ADMFC) circuit is proposed to reduce electromagnetic interference (EMI) on a field-programmable gate array (FPGA) architecture, while supporting dynamic adaptation to voltage noises. The proposed ADMFC uses dedicated high-speed carry chain paths in an FPGA to finely adjust the clock frequency by controlling the number of carry propagations on the carry chain logics (CARRY4 cells) in the delay line of a ring oscillator. Moreover, supply voltage variation and noise caused by circuit switchings can be compensated by dynamically adjusting the length of ripple carry propagations on the cascaded CARRY4 cells in response to the detected voltage variation. Finally, a selectable modulation profile is devised to provide a much suitable profile between two different profiles at run-time for the given noise constraints and working environment of a chip. Measurement results show that at the frequency of 44.6[Formula: see text]MHz, the ADMFC can obtain 17[Formula: see text]dB and 19.4[Formula: see text]dB EMI attenuations with a 7.5% spreading ratio when using triangular and sawtooth profiles, respectively. The proposed ADMFC is suitable for applications such as biological sensor nodes or IoT related systems which typically operate at a low-frequency band.


2014 ◽  
Vol 19 (1) ◽  
pp. 69-81 ◽  
Author(s):  
R. M. Miranda ◽  
B. Tomás ◽  
T. G. Santos ◽  
N. Fernandes

Magnetic Pulse Welding (MPW) applies the electromagnetic principles postulated in the XIXth century and later demonstrated. In recent years the process has been developed to meet highly demanding market needs involving dissimilar material joining, specially involving difficult-to-weld materials. It is a very high speed joining process that uses an electromagnetic force to accelerate one material against the other, resulting in a solid state weld with no external heat source and no thermal distortions. A high power source, the capacitor, a discharge switch and a coil constitute the minimum equipment necessary for this process. A high intensity current flowing through a coil near an electrically conductive material, locally produce an intense magnetic field that generates eddy currents in the flyer according to Lenz law. The induced electromotive force gives rise to a current whose magnetic field opposes the original change in magnetic flux. The effect of this secondary current moving in the primary magnetic field is the generation of a Lorentz force, which accelerates the flyer at a very high speed. If a piece of material is placed in the trajectory of the flyer, the impact will produce an atomic bond in a solid state weld. This paper discusses the fundamentals of the process in terms of phenomenology and analytical modeling and numerical simulation. Recent industrial applications are presented in terms of materials, joint configurations and real examples as well as advantages and disadvantages of the process.


Author(s):  
Hongbo Qiu ◽  
Kaiqiang Hu ◽  
Ran Yi ◽  
Wei Yanqi

Purpose A large number of high-frequency harmonic voltages exist in the output voltage of the inverter, which will affect the performance of the motor. The purpose of this paper is to obtain the influence of high frequency harmonic voltage on the performance of the line start permanent magnet synchronous motor (LSPMSM) and reveal the mechanism of influence. The research results can provide help for the design of LSPMSM driven by inverter drives. Design/methodology/approach First, the actual output voltage data of the inverter is collected, and then the fundamental voltage and high frequency harmonic voltage data can be obtained by performing the fast Fourier transformation method on the voltage data. Second, the finite element model is established. During the finite element calculation, the obtained fundamental voltage and the main harmonic voltage components are used as the voltage source. To research the effect of high frequency harmonic voltage on the performance of motor, a reference group without high frequency harmonic voltage is set up, which is used to compare and analyze the effect of high-frequency harmonics on the performance of the motor. To verify the correctness of the model, a prototype based on the model parameters is manufactured, and then the back EMF experiment and load experiment are performed. The test data and calculation results are compared and analyzed. Findings The coupling relationship between high frequency time harmonic magnetic field and low frequency space harmonic magnetic field is obtained. The stator copper loss and rotor eddy-current loss are calculated and analyzed under normal supply voltage and abnormal supply voltage, and the influence mechanism is revealed Originality/value The coupling relationship between high frequency time harmonic magnetic field and low frequency space harmonic magnetic field is obtained. The sensitivity of the high frequency harmonic voltage to the stator copper loss and rotor eddy-current loss is obtained, and the mechanism of losses change is revealed.


2019 ◽  
pp. 52-58
Author(s):  
A. B. Vasenin ◽  
S. E. Stepanov ◽  
O. V. Kryukov

The present technical condition of the fleet of electric motors serving the actuators of the infrastructure facilities of the fuel and energy complex is presented. The statistics of damage and damage from abnormal operation of electric drive units operating on mechanisms with a fan and pump load are given. The analysis of the causes of the increase in the range of vibration displacement, which leads to premature failure of electric motors, is given. A method for reliably determining the causes of damage, based on measuring and analyzing the electrical parameters of the harmonic spectrum of the motor current, is proposed. Its essence consists in creation of the universal diagnostic system working at the physical principle at which any indignations in work of an electric and mechanical part of the engine and related actuator lead to modulation of the consumed current. Existence in a range of current of characteristic frequencies of a certain size demonstrates existence of these or those damages. The device for its implementation includes phase current sensors of the supply voltage, a signal conditioner for normalizing and filtering signals, an analog-to-digital converter with a USB interface, and a controller with software for analyzing, evaluating, and diagnosing the condition. Experimental results have been obtained confirming the adequacy of the methodology and technical means for monitoring electric motors of various mechanisms.


Twenty-five years ago Lord Rutherford prepared his Address as President of the 1938 Session of the Indian Association for the Advancement of Science at a time when nuclear physics was moving rapidly forward. New disintegrations produced by α -particles and by charged particles accelerated in high-voltage vacuum tubes and cyclotrons were being discovered with great frequency, and neutrons, especi­ally slow neutrons, were being used to produce radioactive isotopes of many of the stable elements. By 1937 nearly a hundred of such isotopes had been discovered and Fermi and others has shown that the heaviest elements, uranium and thorium, after absorbing slow neutrons underwent a succession of β -disintegrations so pro­ducing elements of higher atomic number; these, Fermi called the ‘transuranic elements'. Rutherford’s Address on the ‘Transmutation of Matter’ briefly reviewed the great discoveries of the previous forty years in which he had played probably the leading role. In the first decade the transmutations of the radioactive elements were discovered, revealing ‘a new and startling subatomic world where atoms break up spontaneously with an enormous release of energy quite uninfluenced by the most powerful agencies at our disposal’; in the second decade his nuclear theory of atomic structure was born and had become generally accepted; ‘it was evident’ he said ‘ that to bring about the transmutation of an atom it was necessary in some way to alter the charge of the mass of the nucleus or both together’; and in the third decade Rutherford achieved this transformation by firing α -particles into nitrogen gas and observing that occasionally hydrogen nuclei endowed with very high velo­city were produced—the α -particle had entered into the nitrogen nucleus to form a compound unstable nucleus which instantly broke up with the emission of a fast proton, leaving behind an isotope of oxygen, having a mass of 17. About a dozen of the light elements could be transformed in a similar way, and in a few cases the energy of the proton and the recoil nucleus exceeded the energy of the incident α -particle. At the end of this third decade Rutherford spoke, in his Anniversary Address as President of the Royal Society on 30 November 1927, of attempts to produce intense magnetic fields and high voltages for general scientific purposes. Dr Coolidge, the director of the General Electric research laboratory had constructed a variant of the Coolidge X-ray tube, fitted with a thin metallic window through which fast electrons could stream out into the air, as Lenard had shown thirty years earlier at a much lower voltage. I read Coolidge’s paper as a research student and as I had had a little experience with high voltages when employed in the research department of the Metropolitan-Vickers Electrical Company, I wrote to Rutherford to ask if I might be admitted to the Cavendish Laboratory to try to accelerate electrons to very high voltages with the object of looking for transmutations by energetic electrons. The M. -V. Co. through the good offices of the then director for research, Mr A. P. M. Fleming, offered me a Tesla transformer which could generate up to 600000 V, and with this in the Cavendish Laboratory I learned how to con­struct vacuum tubes which could withstand about 450000 V in air, and 600000 V when placed under oil. Intense beams of 1 mA of electrons electrostatically focused through a slit orifice in the discharge tube were obtained and were deflected in a magnetic field to obtain a roughly monochromatic beam for scattering experiments. A short time after I began, E. T. S. Walton came to the Laboratory and tried to accelerate electrons by indirect methods, using a rapidly rising magnetic field—a method which later became known as the betatron—and in both these attempts we received great encouragement from ‘The Prof. ’, for he was very hopeful of obtaining copious streams of high-speed electrons and atoms, by one way or another, ‘which have an individual energy far transcending that of the α - and β -particles from radioactive bodies’. At that time, although only α -particles had produced disintegrations, there was no known reason why high-energy electrons should not also enter nuclei and the Prof. was a firm believer in ‘try anything once, and see’. He did recognize that there would be formidable difficulties in obtaining particles having energies of many millions of electron volts but he always hoped that some reactions might be discovered with particles of more modest energy if the supply of them was great enough.


2011 ◽  
Vol 66-68 ◽  
pp. 1012-1016
Author(s):  
Qing Hua Ji ◽  
Meng Jia

In term of the problems that the traditional fluxgate sensors with analog circuit have low temperature adjust ability, the paper does research on closed-loop fluxgate sensors. It takes advantage of high speed AD signal collecting sensor, disposes the signals by single chip, and outputs analog signals by DA chips. It describes the hardware environment and software design, and tests the magnetic field by the new sensor. The results show that: its original temperature coefficient is 6.7×10-10/°C, sensitive temperature coefficient is 2.5×10-4/°C and its linearity comes to 5.4×10-3.


Sign in / Sign up

Export Citation Format

Share Document