Correlation between permanent deformation-related performance parameters of asphalt concrete mixes and binders

2013 ◽  
Vol 3 (3) ◽  
Author(s):  
Kálmán Adorjányi ◽  
Péter Füleki
Keyword(s):  
Asphalt Concrete ◽  
Cyclic Load ◽  
Permanent Deformation ◽  
Performance Ratio ◽  
Performance Parameters ◽  
Recoverable Strain ◽  
Recoverable Compliance ◽  
The Difference ◽  
Unrecovered Strain

AbstractThis paper examines methods to predict the performance of hot asphalt concrete mixes based on performance parameters of binders. Specifically, relationships between binder parameters determined from multiple stress creep and recovery tests were correlated to the creep parameters of hot asphalt concrete mixes obtained from cyclic load compression testing. For the determination of creep parameters, a modified expression of the creep curve is proposed to cover the entire spectrum of permanent deformation; including the tertiary creep phase. Non-recoverable compliance, unrecovered strain, and recoverable strain of binders show good correlation to creep parameters of hot asphalt concrete mixes such as creep rate and high temperature performance ratio. Additionally, unrecovered strain and non-recoverable compliance of binders correlates well with mean rut depth of asphalt concrete mixes. However, no correlation has been detected between the difference in non-recoverable compliance of binders and permanent deformation parameters of asphalt concrete mixes.

FRACTIONAL DETERMINATIONS OF URINARY 17-KETOSTEROIDS IN HYPEREMESIS GRAVIDARUM

1962 ◽  
Vol 41 (1) ◽  
pp. 123-128 ◽  
Author(s):  
Pentti A. Järvinen ◽  
Sykkö Pesonen ◽  
Pirkko Väänänen
Keyword(s):  
Hyperemesis Gravidarum ◽  
First Trimester ◽  
Control Group ◽  
Before And After ◽  
Daily Urine ◽  
First Trimester Of Pregnancy ◽  
The Difference

ABSTRACT The fractional determination of 17-ketosteroids in the daily urine was performed in nine cases of hyperemesis gravidarum and in four control cases, in the first trimester of pregnancy both before and after corticotrophin administration. The excretion of total 17-KS is similar in the two groups. Only in the hyperemesis group does the excretion of total 17-KS increase significantly after corticotrophin administration. The fractional determination reveals no difference between the two groups of patients with regard to the values of the fractions U (unidentified 17-KS), A (androsterone) and Rest (11-oxygenated 17-KS). The excretion of dehydroepiandrosterone is significantly higher in the hyperemesis group than in the control group. The excretion of androstanolone seems to be lower in the hyperemesis group than in the control group, but the difference is not statistically significant. The differences in the correlation between dehydroepiandrosterone and androstanolone in the two groups is significant. The high excretion of dehydroepiandrosterone and low excretion of androstanolone in cases of hyperemesis gravidarum is a sign of adrenal dysfunction.

THE SUBJECT FIELD OF INSTITUTIONAL EDUCATION: THE SENSE AND PROSPECTS OF DEVELOPMENT IN UKRAINE

2020 ◽  
pp. 25-38
Author(s):  
Irina Mordous
Keyword(s):  
Decisive Role ◽  
Subject Field ◽  
National Education ◽  
Progressive Development ◽  
Separate Area ◽  
Economic Transformations ◽  
The Difference ◽  
The Individual ◽  
Political Economic

The development of modern civilization attests to its decisive role in the progressive development of institutions. They identified the difference between Western civilization and the rest of the world. Confirmation of the institutional advantages of the West was its early industrialization. The genesis and formation of institutionalism in its ideological and conceptualmethodological orientation occurs as a process alternative to neoclassic in the context of world heterodoxia, which quickly spread in social science. Highlighting institutional education as a separate area of sociocultural activity is determined by the factor of differentiation of institutional theory as a whole. A feature of institutional education is its orientation toward the individual and his/her transformation into a personality. The content of institutional education is revealed through the analysis of the institution, which includes a set of established customs, traditions, ways of thinking, behavioral stereotypes of individuals and social groups. The dynamics of socio-political, economic transformations in Ukraine requires a review of the foundations of national education and determination of the prospects for its development in the 21st century in the context of institutionalism.

scholarly journals Prognostic Assessment of the Performance Parameters for the Industrial Diesel Engines Operated with Microalgae Oil

2021 ◽  
Vol 13 (11) ◽  
pp. 6482
Author(s):  
Sergejus Lebedevas ◽  
Laurencas Raslavičius
Keyword(s):  
Energy Efficiency ◽  
Diesel Engine ◽  
High Speed ◽  
Performance Parameters ◽  
Prognostic Assessment ◽  
High Speed Diesel ◽  
Microalgae Oil ◽  
The Difference ◽  
Smoke Opacity ◽  
Efficiency Indicators

A study conducted on the high-speed diesel engine (bore/stroke: 79.5/95.5 mm; 66 kW) running with microalgae oil (MAO100) and diesel fuel (D100) showed that, based on Wibe parameters (m and φz), the difference in numerical values of combustion characteristics was ~10% and, in turn, resulted in close energy efficiency indicators (ηi) for both fuels and the possibility to enhance the NOx-smoke opacity trade-off. A comparative analysis by mathematical modeling of energy and traction characteristics for the universal multi-purpose diesel engine CAT 3512B HB-SC (1200 kW, 1800 min−1) confirmed the earlier assumption: at the regimes of external speed characteristics, the difference in Pme and ηi for MAO100 and D100 did not exceeded 0.7–2.0% and 2–4%, respectively. With the refinement and development of the interim concept, the model led to the prognostic evaluation of the suitability of MAO100 as fuel for the FPT Industrial Cursor 13 engine (353 kW, 6-cylinders, common-rail) family. For the selected value of the indicated efficiency ηi = 0.48–0.49, two different combinations of φz and m parameters (φz = 60–70 degCA, m = 0.5 and φz = 60 degCA, m = 1) may be practically realized to achieve the desirable level of maximum combustion pressure Pmax = 130–150 bar (at α~2.0). When switching from diesel to MAO100, it is expected that the ηi will drop by 2–3%, however, an existing reserve in Pmax that comprises 5–7% will open up room for further optimization of energy efficiency and emission indicators.

scholarly journals Possibility of Human Gender Recognition Using Raman Spectra of Teeth

Molecules ◽  
2021 ◽  
Vol 26 (13) ◽  
pp. 3983
Author(s):  
Ozren Gamulin ◽  
Marko Škrabić ◽  
Kristina Serec ◽  
Matej Par ◽  
Marija Baković ◽  
...  
Keyword(s):  
Raman Spectra ◽  
Principal Component ◽  
Support Vector ◽  
Gender Recognition ◽  
Proof Of Concept ◽  
Male And Female ◽  
Tooth Type ◽  
Tooth Apex ◽  
The Difference

Gender determination of the human remains can be very challenging, especially in the case of incomplete ones. Herein, we report a proof-of-concept experiment where the possibility of gender recognition using Raman spectroscopy of teeth is investigated. Raman spectra were recorded from male and female molars and premolars on two distinct sites, tooth apex and anatomical neck. Recorded spectra were sorted into suitable datasets and initially analyzed with principal component analysis, which showed a distinction between spectra of male and female teeth. Then, reduced datasets with scores of the first 20 principal components were formed and two classification algorithms, support vector machine and artificial neural networks, were applied to form classification models for gender recognition. The obtained results showed that gender recognition with Raman spectra of teeth is possible but strongly depends both on the tooth type and spectrum recording site. The difference in classification accuracy between different tooth types and recording sites are discussed in terms of the molecular structure difference caused by the influence of masticatory loading or gender-dependent life events.

scholarly journals Influence of Erythrocytes on Direct Potentiometric Determination of Sodium and Potassium

1983 ◽  
Vol 20 (2) ◽  
pp. 116-120 ◽  
Author(s):  
P Bijster ◽  
H L Vader ◽  
C L J Vink
Keyword(s):  
Whole Blood ◽  
Potassium Concentration ◽  
Reference Electrode ◽  
Sodium Concentration ◽  
General Phenomenon ◽  
Liquid Junction ◽  
Direct Potentiometry ◽  
The Difference ◽  
Sodium And Potassium

We have shown that the sodium concentration in whole blood measured by direct potentiometry is higher than in plasma. The ‘erythrocyte-effect’, already described by Siggaard Andersen, is most pronounced for instruments equipped with a reference electrode with an open static liquid junction and is thus a general phenomenon. Instruments with a modified liquid junction show less interference. The same phenomenon appears for the determination of the potassium concentration, although the difference between whole blood and plasma, when measured with instruments equipped with a modified liquid junction, can be neglected in practice.

Method for the simultaneous quantification of n-hexane metabolites: application to n-hexane metabolism determination

1996 ◽  
Vol 15 (6) ◽  
pp. 497-503 ◽  
Author(s):  
T. Soriano ◽  
M. Menéndez ◽  
P. Sanz ◽  
M. Repetto
Keyword(s):  
Similar Pattern ◽  
Analytical Procedure ◽  
Daily Basis ◽  
Practical Application ◽  
Simultaneous Quantification ◽  
Exposed Workers ◽  
Before And After ◽  
Time Requirements ◽  
The Difference

1 The described analytical procedure permits the simultaneous determination of the main n-hexane meta bolites in urine. 2-Hexanone, 2-hexanol, 2, 5-hexanediol and 2, 5-hexanedione, were chosen to dose the rats used in this study. All urine samples were collected and analysed on a daily basis, before and after acidic hydrolysis (pH 0.1) by GC/MS. 2-Hexanone, 2, 5-dimethylfurane, γ-valerolac tone and 2, 5-hexanedione were determined before hydro lysis ; 2-hexanol and 2, 5-hexanediol, after hydrolysis; and 5-hydroxy-2-hexanone and 4, 5-dihydroxy-2-hexanone were calculated by the difference between γ-valerolactone and 2, 5-hexanedione with and without hydrolysis, respectively. 2 A metabolic scheme was proposed reflecting the biotransformations undergone by the four compounds assayed. We consider 2, 5-dimethylfurane as a 'true metabolite' because the quantities detected were always greater before hydrolysis. 3 It has been reported that human and rat n-hexane metabolism follow a similar pattern. Therefore, as a practical application and without increasing either sample or time requirements, the simultaneous quantifi cation of the different metabolites and their excretion profile could provide better information about the metabolic situation of exposed workers than the determi nation of 2, 5-hexanedione alone. According to our experimental results, 4, 5-dihydroxy-2-hexanone itself would be a good toxicity indicator.

Mitigation of permanent deformation in base layer containing recycled asphalt aggregates

2013 ◽  
Vol 40 (2) ◽  
pp. 181-187 ◽  
Author(s):  
Jean-Pascal Bilodeau ◽  
Guy Doré ◽  
Jonas Depatie
Keyword(s):  
Asphalt Concrete ◽  
Deformation Behaviour ◽  
Permanent Deformation ◽  
Design Procedure ◽  
Base Layer ◽  
Repeated Loading ◽  
Recycled Asphalt ◽  
Thickness Increase ◽  
Permanent Strain ◽  
Pavement Base

The use of recycled asphalt pavement (RAP) aggregates as replacement for new materials in the pavement base weakens the layer in regards to the resistance to permanent deformation under repeated loading. A mechanistic based design procedure is proposed to ensure that base layers containing RAP particles have a similar rutting behaviour to base layers made of virgin aggregates. The design procedure allows calculating an asphalt concrete thickness increase that is based on permanent deformation behaviour of base materials. The calculation approach is based on multistage triaxial permanent deformation tests performed on granular material samples with varied RAP content. The tests allowed proposing an equation that relates permanent strain rate, RAP content, and deviatoric stress, which is the basis of the design procedure. Design charts are proposed to select adequate thickness increase for the asphalt concrete layer according to the expected RAP content in the base layer and asphalt concrete modulus.

Determination of Resistance to Abrasive Wear. VIII. Influence of Softeners in Tests with the Akron-Croydon and Du Pont Machines

1949 ◽  
Vol 22 (1) ◽  
pp. 259-262
Author(s):  
J. F. Morley
Keyword(s):  
Unit Area ◽  
Published Data ◽  
The Road ◽  
Abrasive Surface ◽  
Abrasive Power ◽  
The Difference ◽  
On The Road ◽  
The Right ◽  
Abrasion Testing

Abstract These experiments indicate that softeners can influence abrasion resistance, as measured by laboratory machines, in some manner other than by altering the stress-strain properties of the rubber. One possible explanation is that the softener acts as a lubricant to the abrasive surface. Since this surface, in laboratory abrasion-testing machines, is relatively small, and comes repeatedly into contact with the rubber under test, it seems possible that it may become coated with a thin layer of softener that reduces its abrasive power. It would be interesting in this connection to try an abrasive machine in which a long continuous strip of abrasive material was used, no part of it being used more than once, so as to eliminate or minimize this lubricating effect. The fact that the effect of the softener is more pronounced on the du Pont than on the Akron-Croydon machine lends support to the lubrication hypothesis, because on the former machine the rate of wear per unit area of abrasive is much greater. Thus in the present tests the volume of rubber abraded per hr. per sq. cm. of abrasive surface ranges from 0.03 to 0.11 cc. on the du Pont machine and from 0.0035 to 0.0045 cc. on the Akron-Croydon machine. On the other hand, if the softener acts as a lubricant, it would be expected to reduce considerably the friction between the abrasive and the rubber and hence the energy used in dragging the rubber over the abrasive surface. The energy figures given in the right-hand columns of Tables 1 and 3, however, show that there is relatively little variation between the different rubbers. As a test of the lubrication hypothesis, it would be of interest to vary the conditions of test so that approximately the same amount of rubber per unit area of abrasive is abraded in a given time on both machines; this should show whether the phenomena observed under the present test conditions are due solely to the difference in rate of wear or to an inherent difference in the type of wear on the two machines. This could most conveniently be done by considerably reducing the load on the du Pont machine. In the original work on this machine the load was standardized at 8 pounds, but no figures are quoted to show how abrasion loss varies with the load. As an addition to the present investigation, it is proposed to examine the effect of this variation with special reference to rubbers containing various amounts and types of softener. Published data on the influence of softeners on the road wear of tire rubbers do not indicate anything like such large effects as are shown by the du Pont machine. This throws some doubt on the value of this machine for testing tire tread rubbers, a conclusion which is confirmed by information obtained from other workers.

Sign in / Sign up

Export Citation Format

Share Document