scholarly journals PROSES ULTRAFILTRASI UNTUK PENJERNIHAN SARI BUAH MARKISA (Passiflora quadrangularis) DENGAN MEMANFAATKAN MEMBRAN KERAMIK

2016 ◽  
Vol 9 (2) ◽  
pp. 36
Author(s):  
Refinel ◽  
Olly Norita Tetra ◽  
Olly Norita Tetra ◽  
Roza Melia Usmita ◽  
Roza Melia Usmita
Keyword(s):  
Vitamin C ◽  
Fruit Juice ◽  
Ceramic Membrane ◽  
Chemical Properties ◽  
Reducing Sugar ◽  
Passion Fruit ◽  
Before And After ◽  
Rejection Coefficient ◽  
Physical And Chemical ◽  
And Chemical Properties

Ultrafiltration of passion fruit juice using variation thickness of ceramic membrane has been done.  The result shows that aquades flux value in 25 minutes for membrane 1.5; 2.0; 2.5; 3.0; and 3.5 mm is 17.0135; 19.1947; 10.9061; 10.9061 and 4.3624 L/h m2. Whereas passion fruit juice in same time for membrane 1.5; 2.0; 2.5 mm is 8.2886; 5.6712 and 4.3624 L/h m2. For membrane 3.0 and 3.5 mm it has not been done because flux value are too small that indicate fouling. Physical and chemical properties parameter in ultrafiltration of passion fruit juice obtained for turbidity and color very different between passion fruit juice before and after ultrafiltration, whereas reducing sugar and vitamin C are not significant different between passion fruit juice before and after ultrafiltration. Determination rejection coefficient value of membrane for turbidity, color  relatively significant whereas for reducing sugar and vitamin C are relatively not significant.

scholarly journals Quality Attributes of Malaysia Purple-Fleshed Sweet Potato at Different Peel Condition

Agronomy ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 872
Author(s):  
Nurfarhana Shaari ◽  
Rosnah Shamsudin ◽  
Mohd Zuhair Mohd Nor ◽  
Norhashila Hashim
Keyword(s):  
Vitamin C ◽  
Sweet Potato ◽  
Dry Matter ◽  
Nutritional Value ◽  
Amylose Content ◽  
Starch Content ◽  
Chemical Properties ◽  
Physical And Chemical Properties ◽  
Physical And Chemical ◽  
And Chemical Properties

In this study, physical and chemical properties (dry matter, ash, moisture, protein, fat, fiber, carbohydrate, starch, amylose, and vitamin C) of sweet potato tuber and flour of Anggun 1 cultivar were evaluated at different conditions. During peeling, the tuber and flour were processed subjected to three different conditions, which were unpeeled tubers (C1), peeled tubers (C2), and skin of tuber only (C3). From the results, the highest (p < 0.05) dry matter was observed in C1 while higher contents of ash, moisture, and protein were found in C3. Regarding the fat and vitamin C content, no significant differences (p > 0.05) were found between each condition. The highest fiber, carbohydrate, and amylose content (p < 0.05) were found in C1. The C1 and C2 reflected significantly higher (p < 0.05) starch content. Overall, these results provide important information about the peeling effect on the physical and chemical properties of Anggun 1. The information could be used as adding value to healthy food in the Malaysian diet due to the nutritional value of sweet potato.

Identification of Amber and the Copal under Heat Pressurized Process

2012 ◽  
Vol 554-556 ◽  
pp. 2112-2115
Author(s):  
Hui Li ◽  
Xuan Wang ◽  
Yong Zhu ◽  
Qin Ren
Keyword(s):  
Chemical Properties ◽  
Peak Position ◽  
Exothermic Peak ◽  
Endothermic Peak ◽  
Scanning Calorimetry ◽  
Natural Resin ◽  
Before And After ◽  
Artificial Heat ◽  
Physical And Chemical ◽  
And Chemical Properties

Amber and copal belong to the natural resin, which are similar and transitional in the physical and chemical properties. The artificial heat-pressurized treatment is contributed to the polymerization of the natural copal, and turns into green, yellow-green and deep orange-yellow copal. It is very difficult to identify amber from the heat- pressurized treatment copal only based on the gemological parameters.The thermal behavior of amber and the copal before and after heat-pressurized treatment were analyzed by means of differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy(FTIR) and nuclear magnetic resonance(NMR). The results show that amber exists an evident endothermic peak around 123~132°C, and copal reveals an obvious endothermic peak at about 174~178°C, and the heat pressurized treatment copal occurs a clear exothermic peak around 150~152°C. The differences between endothermic or exothermic transition and peak position reveal occurring thermal oxidation or the bond breaking or the melting, which are of great significance in the identification.

scholarly journals Produksi Biofuel Dari Limbah Cpo Dengan Katalis Berbasis Titanium Oksida Dan Implementasinya Pada Pembelajaran Kimia

2017 ◽  
Vol 1 (1) ◽  
pp. 19-24
Author(s):  
Nurlia Latifah ◽  
Agus Sundaryono ◽  
Rina Elvia
Keyword(s):  
Methyl Ester ◽  
Learning Outcomes ◽  
Alternative Energy ◽  
Chemical Properties ◽  
Student Learning Outcomes ◽  
Tio2 Catalyst ◽  
Before And After ◽  
Cracking Process ◽  
Physical And Chemical ◽  
And Chemical Properties

Conversion of CPO waste into biofuel is one of the efforts to find alternative energy to overcome Indonesia's energy crisis. The resulting methyl ester was further processed into biofuel by cracking process with Ni/TiO2 and Co/TiO2 catalysts at temperature > 350oC for 2.5 hours followed by distillation. Educational research was done by doing the learning process by using biofuel module. The optimum biofuel yield was obtained from cracking methyl ester with 5% Ni/TiO2 catalyst and 3% Co/TiO2 catalyst respectively of 66,67 and 61,90%. The physical and chemical properties of cracked biofuels with Ni/TiO2 and Co/ TiO2 catalysts have complied with ASTM standards for biofuel except acid numbers. There is an increase in student learning outcomes before and after using the module. 

scholarly journals Semen characteristics of breeding bulls at the Central Cattle Breeding and Dairy Farm of Bangladesh

2012 ◽  
Vol 41 (1) ◽  
pp. 1-5
Author(s):  
ME Hossain ◽  
MM Khatun ◽  
MM Islam ◽  
OF Miazi
Keyword(s):  
Sperm Concentration ◽  
Chemical Properties ◽  
Dairy Farm ◽  
Mean Value ◽  
Cattle Breeding ◽  
Bull Semen ◽  
Before And After ◽  
The Mean ◽  
Physical And Chemical ◽  
And Chemical Properties

The experiment was conducted on 97 breeding bulls at the central cattle breeding and dairy farm, Savar, Dhaka to find out the physical and chemical properties of different bull semen. Out of 97 bulls, 9 were Local (L), 9 were Friesian (F), 13 were Sahiwal (SL), 12 were Local×Friesian (L×F), 10 were Sahiwal×Friesian (SL×F), 26 were Local×Friesian×Friesian (LF1×F), 18 were Local×Friesian× Friesian×Friesian (LF2×F) bulls. The semen of different crossbred and local bulls was examined for ejaculate volume, concentration, pH and motility percent of sperm before and after freezing. It was observed that, the maximum average ejaculate was obtained from SL×F and the mean value was 12.9 ml. However, the minimum average ejaculate was obtained from LF×F and the mean value was 7.4 ml. Before freezing, the maximum average sperm concentration was obtained from SL and the mean value was 1858.4 million/ml. The minimum average sperm concentration was obtained from LF1×F and the mean value was 1286.6 million/ml. The maximum average pH was obtained from LF2×F and the mean value was 6.5. The maximum average motility was obtained from SL and the mean value was 68.8%. However, the minimum average motility was obtained from L×F and the mean value was 63.7%. After freezing, sperm concentration, pH and motility reduced substantially irrespective of type of breed. It could therefore be inferred that freezing of semen should be undertaken with special care to maintain optimum semen quality.http://dx.doi.org/10.3329/bjas.v41i1.11968

The Aging Characteristics of Composite Insulators under Salt Fog Conditions

2014 ◽  
Vol 496-500 ◽  
pp. 231-237 ◽  
Author(s):  
Xiao Chun Chen ◽  
Min Cong Zheng ◽  
Jian Hua Li
Keyword(s):  
Ftir Spectroscopy ◽  
Chemical Properties ◽  
Accelerated Aging ◽  
Physical And Chemical Properties ◽  
Filling Materials ◽  
Aging Properties ◽  
Before And After ◽  
Physical And Chemical ◽  
Salt Fog ◽  
And Chemical Properties

The accelerated aging tests under salt fog conditions were carried out on two types of composite insulators in order to evaluate their anti-aging properties. FTIR spectroscopy, hydrophobicity, and hardness measurements were taken to characterize insulator housings' physical and chemical properties before and after aging. It was found that the aging characteristics were highly dependent on housing profile, aging time, and filling materials.

scholarly journals PRODUKSI BIOFUEL DARI LIMBAH CPO DENGAN KATALIS BERBASIS TITANIUM OKSIDA DAN IMPLEMENTASINYA PADA PEMBELAJARAN KIMIA

2017 ◽  
Vol 1 (1) ◽  
Author(s):  
Nurlia Latifah ◽  
Agus Sundaryono ◽  
Rina Elvia
Keyword(s):  
Methyl Ester ◽  
Learning Outcomes ◽  
Alternative Energy ◽  
Chemical Properties ◽  
Student Learning Outcomes ◽  
Tio2 Catalyst ◽  
Before And After ◽  
Cracking Process ◽  
Physical And Chemical ◽  
And Chemical Properties

Conversion of CPO waste into biofuel is one of the efforts to find alternative energy to overcome Indonesia's energy crisis. The resulting methyl ester was further processed into biofuel by cracking process with Ni/TiO2 and Co/TiO2 catalysts at temperature > 350oC for 2.5 hours followed by distillation. Educational research was done by doing the learning process by using biofuel module. The optimum biofuel yield was obtained from cracking methyl ester with 5% Ni/TiO2 catalyst and 3% Co/TiO2 catalyst respectively of 66,67 and 61,90%. The physical and chemical properties of cracked biofuels with Ni/TiO2 and Co/ TiO2 catalysts have complied with ASTM standards for biofuel except acid numbers. There is an increase in student learning outcomes before and after using the module. 

scholarly journals Comparative Microstructural Study on Mechanical Properties of Concrete Enhanced with Graphite and Graphene Compound

2018 ◽  
Vol 7 (4.5) ◽  
pp. 91
Author(s):  
P. Sudheer ◽  
Dr S. Chandramouli
Keyword(s):  
Mechanical Properties ◽  
Raw Materials ◽  
Chemical Properties ◽  
Nano Materials ◽  
Nano Technology ◽  
Microstructural Investigation ◽  
Before And After ◽  
Materials Used ◽  
Physical And Chemical ◽  
And Chemical Properties

The present study is based on nano technology and came up with the idea of introducing nanoparticles in the raw materials used for construction. Nano materials are available in three principal shapes 0, 1 and 2 Dimensional nanoparticles. 0D and 1D nanofibers are such as carbon nanotubes and nanosilica compounds. This study has investigated the physical and chemical properties of graphite and graphene compound and its applicability in construction industry.  Graphene has created interest as it is believed to improve the strength of concrete allowing the possibility of controlling properties of concrete. In this work graphene is used as a reinforcing additive in cement-based mortar and concrete. Own Graphene compound is prepared using conventional graphite and concentrated hydrogen peroxide in the laboratory due to the unavailability of graphene. As a part of microstructural investigation, SEM and EDS analysis on graphite and graphene compounds before and after implementation are carried out in the laboratory. Then the two compounds are replaced as a part of small percentage in cement mortar cubes casted for various proportions. The mechanical properties of cement-based composites are studied after incorporating of graphite and graphene compounds at low dosages in concrete and then the results are compared. 

scholarly journals Physical and chemical quality of processed nectar flavors and sold in supermarkets in the city of Cuiabá-MT

2016 ◽  
Vol 7 (3) ◽  
pp. 16
Author(s):  
Kelly Rodrigues Gobbi ◽  
Livia Rodrigues Almeida ◽  
Melissa Schirmer ◽  
Rozilaine Aparecida Pelegrine Gomes Faria
Keyword(s):  
Vitamin C ◽  
Reducing Sugar ◽  
Passion Fruit ◽  
Soluble Solids ◽  
Chemical Quality ◽  
Physical And Chemical Quality ◽  
Fruit Flavor ◽  
Physical And Chemical ◽  
The City

This study aimed to evaluate the physical and chemical quality of processed passion fruit and peach nectar flavors and sold in supermarkets in the city of Cuiaba-MT. We evaluated the physicochemical parameters total acidity, citric acid, pH, vitamin C content, soluble solids (° Brix) SS/acidity total, reducing and non-reducing and total carbohydrates, as the Institute Adolf Lutz standards. The mean values were subjected to analysis of variance and were submitted to the Scott-Knott test at 5% significance level. The total acidity (g.100g-1) to B and D showed statistically equal averages. However, passion fruit flavor of the brand B showed higher pH value (3.27 ± 0.02a). There was no statistically significant difference in soluble solids / titratable acidity (SS / TA) between the marks for the analyzed flavors. For vitamin C all values were below prescribed by legislation. For total soluble solids the average observed for the passion fruit flavor met the minimum established by legislation. However, for the peach flavor, the marks A and B showed lower values and they were smaller than the minimum values established by legislation. Regarding the parameter non-reducing sugar, the brand presented the biggest non-reducing sugar values for the flavors to analyzed. We concluded that not all analyzed parameters meet the current legislation. Vitamin C and soluble solids were below the established by legislation. There is no standard of identity and quality for non-reducing sugar as sucrose, so important parameter as a criterion of a healthy food.

scholarly journals Water Treatment using Chemically Activated Charcoal

2020 ◽  
Vol 5 (3) ◽  
pp. 72-78
Keyword(s):  
Activated Charcoal ◽  
Potassium Dichromate ◽  
Chemical Properties ◽  
Physical And Chemical Properties ◽  
Coconut Husk ◽  
Before And After ◽  
Worldwide Phenomenon ◽  
Physical And Chemical ◽  
Absorbance Data ◽  
And Chemical Properties

Water scarcity is a widely experienced problem in several countries in the world like Qatar, Israel, Lebanon and many others. Critical steps have to be taken before this becomes a worldwide phenomenon. The current study focuses on cleaning the greywater, which is about 65% of total wastewater from households, using activated charcoal powder prepared from coconut husk. The material is chemically activated. The shell based activated carbon is used for decolorization of three solution samples: Potassium Permanganate (Purple), Potassium Dichromate (Orange) and Copper Sulphate (Blue) as well as treating the sullage water. Change in normality of above-mentioned samples is calculated before and after treatment by activated charcoal using maximum absorbance data for before treatment as standard. Also, sullage water is treated with activated charcoal and comparison of physical and chemical properties is done before and after the treatment.

scholarly journals The Investigation of Organic Binder Effect on Morphological Structure of Ceramic Membrane Support

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 770 ◽  
Author(s):  
Mohamed Boussemghoune ◽  
Mustapha Chikhi ◽  
Yasin Ozay ◽  
Pelin Guler ◽  
Bahar Ozbey Unal ◽  
...  
Keyword(s):  
Ceramic Membrane ◽  
Thermo Gravimetric Analysis ◽  
Chemical Properties ◽  
Morphological Structure ◽  
Clay Material ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties

In this study, we investigated the effect of different organic binders on the morphologic structure of ceramic membrane support. Natural raw clay material (kaolin) was used as the main mineral for ceramic membrane support. The physical and chemical properties of kaolin powder and the supports were identified by X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET), thermo gravimetric analysis (TGA), scanning electron microscopy (SEM), particle size and zeta potential distribution. Based on the XRF test, the main composition of kaolin powder was SiO2 (47.41%) and Al2O3 (38.91%), while the rest were impurities. The FTIR spectra showed the functional groups of Si-O and Al-O. The XRD diffractogram of natural raw clay powder identified kaolinite and nacrite were the main mineral phase whereas muscovite and quartz were detected in small quantities in the sample. After prepared the ceramic membrane supports, XRD diffractogram showed that anorthite and gehlenite were detected as the main mineral phases for ethylene glycol (EG), gelatin, methocel and for polyethylene glycol (PEG), respectively. According to BET analyses, the maximum and the minimum pore width were obtained for PEG and gelatin organic binders.

Sign in / Sign up

Export Citation Format

Share Document