Thin-Die Flip Chip Physical-FA Process Flow

2002 ◽  
Author(s):  
Andrew J. Komrowski ◽  
N. S. Somcio ◽  
Daniel J. D. Sullivan ◽  
Charles R. Silvis ◽  
Luis Curiel ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Fault Isolation ◽  
Preparation Methods ◽  
Chip Technology ◽  
Isolation Test ◽  
Sample Preparation Methods

Abstract The use of flip chip technology inside component packaging, so called flip chip in package (FCIP), is an increasingly common package type in the semiconductor industry because of high pin-counts, performance and reliability. Sample preparation methods and flows which enable physical failure analysis (PFA) of FCIP are thus in demand to characterize defects in die with these package types. As interconnect metallization schemes become more dense and complex, access to the backside silicon of a functional device also becomes important for fault isolation test purposes. To address these requirements, a detailed PFA flow is described which chronicles the sample preparation methods necessary to isolate a physical defect in the die of an organic-substrate FCIP.

Lock-in Thermography for Flip-Chip Package Failure Analysis

2012 ◽  
Author(s):  
Lihong Cao ◽  
Manasa Venkata ◽  
Jeffery Huynh ◽  
Joseph Tan ◽  
Meng-Yeow Tay ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Case Studies ◽  
Flip Chip ◽  
Organic Substrate ◽  
Fault Isolation ◽  
Lock In

Abstract This paper describes the application of lock-in thermography (LIT) for flip-chip package-level failure analysis. LIT successfully detected and localized short failures related to both die/C4 bumps and package defects inside the organic substrate. The detail sample preparation to create short defects at different layers, LIT fault isolation methodology, and case studies performed with LIT are also presented in this paper.

Failure Analysis of Advanced Microprocessors through Backside Approaches

1998 ◽  
Author(s):  
D. Davis ◽  
O. Diaz de Leon ◽  
L. Hughes ◽  
S. V. Pabbisetty ◽  
R. Parker ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Preparation Methods ◽  
Analysis Techniques ◽  
Analytical Approaches ◽  
Sample Preparation Methods ◽  
New Devices

Abstract The advent of Flip Chip and other complex package configurations and process technologies have made conventional failure analysis techniques inapplicable. This paper covers the ways in which conventional techniques have been modified to meet the FA challenges presented by these new devices – specifically, by forcing analysis to be done from the backside of the device. Modifications to the traditional FA process steps, including new sample preparation methods, changes in hardware, and alterations to physical failure analysis processes are described. To demonstrate the use of backside analytical approaches, some examples of applications and a case study are also included.

A Sample Preparation on Decapsulation Methodology for Effective Failure Analysis on Thin Small Leadless (TSLP) Flip Chip Package with Copper Pillar (CuP) Bump Interconnect Technology

2014 ◽  
Author(s):  
Gwee Hoon Yen ◽  
Ng Kiong Kay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Localization ◽  
Cost Effective ◽  
Fault Isolation ◽  
Voltage Contrast ◽  
Interconnect Technology

Abstract Today, failure analysis involving flip chip [1] with copper pillar bump packaging technologies would be the major challenges faced by analysts. Most often, handling on the chips after destructive chemical decapsulation is extremely critical as there are several failure analysis steps to be continued such as chip level fault localization, chip micro probing for fault isolation, parallel lapping [2, 3, 4] and passive voltage contrast. Therefore, quality of sample preparation is critical. This paper discussed and demonstrated a quick, reliable and cost effective methodology to decapsulate the thin small leadless (TSLP) flip chip package with copper pillar (CuP) bump interconnect technology.

Failure Analysis of Flip Chip C4 Package Using Focused Ion Beam Milling Technique

2011 ◽  
Author(s):  
Lihong Cao ◽  
Loc Tran ◽  
Wallace Donna
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Cross Sections ◽  
Flip Chip ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Failure Mechanisms ◽  
Organic Substrate ◽  
Dual Beam ◽  
Preparation Techniques

Abstract This article describes how Focused Ion Beam (FIB) milling methodology enhances the capability of package-level failure analysis on flip-chip packages by eliminating the artifacts induced by using conventional mechanical techniques. Dual- Beam Focused Ion Beam (DB FIB) cross sections were successful in detecting failure mechanisms related either to the die/C4 bump or package defect inside the organic substrate. This paper outlines detailed sample preparation techniques prior to performing the DB FIB cross-sections, along with case studies of DB FIB cross-sections.

Improving Sample Preparation Methods For Cannabis-Infused Edible And Topical Products

Planta Medica ◽  
2016 ◽  
Vol 82 (05) ◽  
Author(s):  
M Wilcox ◽  
M Jacyno ◽  
J Marcu ◽  
J Neal-Kababick
Keyword(s):  
Sample Preparation ◽  
Preparation Methods ◽  
Sample Preparation Methods

Failure Analysis of Flip-Chip Interconnections Through Acoustic Microscopy

1996 ◽  
Author(s):  
O. Diaz de Leon ◽  
M. Nassirian ◽  
C. Todd ◽  
R. Chowdhury
Keyword(s):  
Failure Analysis ◽  
Large Scale ◽  
Flip Chip ◽  
Ultrasonic Waves ◽  
Acoustic Microscopy ◽  
Acoustic Microscope ◽  
Chip Technology ◽  
Ball Joints ◽  
Non Destructive ◽  
Scanning Acoustic Microscope

Abstract Integration of circuits on semiconductor devices with resulting increase in pin counts is driving the need for improvements in packaging for functionality and reliability. One solution to this demand is the Flip- Chip concept in Ultra Large Scale Integration (ULSI) applications [1]. The flip-chip technology is based on the direct attach principle of die to substrate interconnection.. The absence of bondwires clearly enables packages to become more slim and compact, and also provides higher pin counts and higher-speeds [2]. However, due to its construction, with inherent hidden structures the Flip-Chip technology presents a challenge for non-destructive Failure Analysis (F/A). The scanning acoustic microscope (SAM) has recently emerged as a valuable evaluation tool for this purpose [3]. C-mode scanning acoustic microscope (C-SAM), has the ability to demonstrate non-destructive package analysis while imaging the internal features of this package. Ultrasonic waves are very sensitive, particularly when they encounter density variations at surfaces, e.g. variations such as voids or delaminations similar to air gaps. These two anomalies are common to flip-chips. The primary issue with this package technology is the non-uniformity of the die attach through solder ball joints and epoxy underfill. The ball joints also present defects as open contacts, voids or cracks. In our acoustic microscopy study packages with known defects are considered. It includes C-SCAN analysis giving top views at a particular package interface and a B-SCAN analysis that provides cross-sectional views at a desired point of interest. The cross-section analysis capability gives confidence to the failure analyst in obtaining information from a failing area without physically sectioning the sample and destroying its electrical integrity. Our results presented here prove that appropriate selection of acoustic scanning modes and frequency parameters leads to good reliable correlation between the physical defects in the devices and the information given by the acoustic microscope.

Extending Acoustic Microscopy for Comprehensive Failure Analysis Applications

2010 ◽  
Author(s):  
Sebastian Brand ◽  
Matthias Petzold ◽  
Peter Czurratis ◽  
Peter Hoffrogge
Keyword(s):  
Image Processing ◽  
Failure Analysis ◽  
Signal Analysis ◽  
Flip Chip ◽  
Fault Isolation ◽  
Acoustic Microscopy ◽  
Specific Information ◽  
Full Potential ◽  
Time Frequency ◽  
Non Destructive

Abstract In industrial manufacturing of microelectronic components, non-destructive failure analysis methods are required for either quality control or for providing a rapid fault isolation and defect localization prior to detailed investigations requiring target preparation. Scanning acoustic microscopy (SAM) is a powerful tool enabling the inspection of internal structures in optically opaque materials non-destructively. In addition, depth specific information can be employed for two- and three-dimensional internal imaging without the need of time consuming tomographic scan procedures. The resolution achievable by acoustic microscopy is depending on parameters of both the test equipment and the sample under investigation. However, if applying acoustic microscopy for pure intensity imaging most of its potential remains unused. The aim of the current work was the development of a comprehensive analysis toolbox for extending the application of SAM by employing its full potential. Thus, typical case examples representing different fields of application were considered ranging from high density interconnect flip-chip devices over wafer-bonded components to solder tape connectors of a photovoltaic (PV) solar panel. The progress achieved during this work can be split into three categories: Signal Analysis and Parametric Imaging (SA-PI), Signal Analysis and Defect Evaluation (SA-DE) and Image Processing and Resolution Enhancement (IP-RE). Data acquisition was performed using a commercially available scanning acoustic microscope equipped with several ultrasonic transducers covering the frequency range from 15 MHz to 175 MHz. The acoustic data recorded were subjected to sophisticated algorithms operating in time-, frequency- and spatial domain for performing signal- and image analysis. In all three of the presented applications acoustic microscopy combined with signal- and image processing algorithms proved to be a powerful tool for non-destructive inspection.

Sample Preparation Challenges In WLCSP Epoxy Underfill Coating Removal

2012 ◽  
Author(s):  
Jason H. Lagar ◽  
Rudolf A. Sia
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Vital Role ◽  
Fault Isolation ◽  
Wafer Level ◽  
Chip Scale Package ◽  
Coating Removal ◽  
Customer Returns ◽  
Preparation Techniques ◽  
Mechanical Defect

Abstract Most Wafer Level Chip Scale Package (WLCSP) units returned by customers for failure analysis are mounted on PCB modules with an epoxy underfill coating. The biggest challenge in failure analysis is the sample preparation to remove the WLCSP device from the PCB without inducing any mechanical defect. This includes the removal of the underfill material to enable further electrical verification and fault isolation analysis. This paper discusses the evaluations conducted in establishing the WLCSP demounting process and removal of the epoxy underfill coating. Combinations of different sample preparation techniques and physical failure analysis steps were evaluated. The established process enabled the electrical verification, fault isolation and further destructive analysis of WLCSP customer returns mounted on PCB and with an epoxy underfill coating material. This paper will also showcase some actual full failure analysis of WLCSP customer returns where the established process played a vital role in finding the failure mechanism.

Cross-Section Sample Preparation Method for Imaging Dopant Related Anomalies Using Scanning Probe Microscopy Techniques

2014 ◽  
Author(s):  
Swaminathan Subramanian ◽  
Khiem Ly ◽  
Tony Chrastecky
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Cross Section ◽  
Scanning Probe Microscopy ◽  
Preparation Method ◽  
Fault Isolation ◽  
Scanning Probe ◽  
Sample Preparation Method ◽  
Probe Microscopy ◽  
Section Sample

Abstract Visualization of dopant related anomalies in integrated circuits is extremely challenging. Cleaving of the die may not be possible in practical failure analysis situations that require extensive electrical fault isolation, where the failing die can be submitted of scanning probe microscopy analysis in various states such as partially depackaged die, backside thinned die, and so on. In advanced technologies, the circuit orientation in the wafer may not align with preferred crystallographic direction for cleaving the silicon or other substrates. In order to overcome these issues, a focused ion beam lift-out based approach for site-specific cross-section sample preparation is developed in this work. A directional mechanical polishing procedure to produce smooth damage-free surface for junction profiling is also implemented. Two failure analysis applications of the sample preparation method to visualize junction anomalies using scanning microwave microscopy are also discussed.

Sign in / Sign up

Export Citation Format

Share Document