Vdd Leakage Analysis by a Combination of Various Failure Analysis Techniques

2008 ◽  
Author(s):  
Z. G. Song ◽  
S. B. Ippolito ◽  
P. J. McGinnis ◽  
A. Shore ◽  
B. Paulucci ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Hot Spot ◽  
Fault Isolation ◽  
Physical Analysis ◽  
Analysis Techniques ◽  
Root Cause ◽  
Defect Location ◽  
Analysis Methodology ◽  
Analysis Process ◽  
Leakage Failure

Abstract It is generally accepted that the fault isolation of Vdd short and leakage can be globally addressed by liquid crystal analysis (LCA), photoemission analysis and/or laser stimulating techniques such as OBIRCH or TIVA. However, the hot spot detected by these techniques may be a secondary effect, rather than the exact physical defect location. Further electrical probing with knowledge of the circuit schematic and layout may still be required to pinpoint the exact physical defect location, so that a suitable physical analysis methodology can be chosen to identify the root cause of the failure. This paper has described a thorough analysis process for Vdd leakage failure by a combination of various failure analysis techniques and finally the root cause of the Vdd leakage was identified.

Single Device Characterization by Nano-probing to Identify Failure Root Cause

2005 ◽  
Author(s):  
Chao-Chi Wu ◽  
Jon C. Lee ◽  
Jung-Hsiang Chuang ◽  
Tsung-Te Li
Keyword(s):  
Failure Analysis ◽  
Success Rate ◽  
Failure Mechanism ◽  
Fault Isolation ◽  
Device Characterization ◽  
Nano Technology ◽  
Analysis Techniques ◽  
Root Cause ◽  
Visual Defects ◽  
Lower Success Rate

Abstract In general failure analysis cases, a less invasive fault isolation approach can be utilized to resolve a visual root cause defect. In the case of nano technology, visual defects are not readily resolved, due to an increase in non-visible defects. The nonvisible defects result in a lower success rate since conventional FA methods/tools are not efficient in identifying the failure root cause. For the advanced nanometer process, this phenomenon is becoming more common; therefore the utilization of advanced techniques are required to get more evidence to resolve the failure mechanism. The use of nanoprobe technology enables advanced device characterization h order to obtain more clues to the possible failure mechanism before utilizing the traditional physical failure analysis techniques.

Failure Analysis Methodology on Circular Patch Functional Failure Due to Device Parametric Drift

2015 ◽  
Author(s):  
A.C.T. Quah ◽  
C.Q. Chen ◽  
G.B Ang ◽  
D. Nagalingam ◽  
H.P. Ng ◽  
...  
Keyword(s):  
Deep Dive ◽  
Circular Patch ◽  
Root Cause ◽  
Analysis Methodology ◽  
Analysis Process ◽  
Value Add ◽  
Challenging Situation ◽  
Leakage Failure ◽  
Parametric Drift

Abstract This paper describes the debug and analysis process of a challenging case study from wafer foundry which involved a circular patch functional leakage failure that was induced from device parametric drift due to thicker gate oxide with no detection signal from inline monitoring vehicles. It highlights the need for failure analyst to always be inquisitive and to deep dive into the failure symptoms to value-add the fab in discovering the root cause of the failure in challenging situation where information is limited.

A New Failure Analysis Flow of Gate Oxide Integrity Failure in Wafer Fabrication

2009 ◽  
Author(s):  
Hua Younan ◽  
Chu Susan ◽  
Gui Dong ◽  
Mo Zhiqiang ◽  
Xing Zhenxiang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Defect Density ◽  
Gate Oxide ◽  
Oxide Thickness ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Root Cause ◽  
Gate Oxide Integrity

Abstract As device feature size continues to shrink, the reducing gate oxide thickness puts more stringent requirements on gate dielectric quality in terms of defect density and contamination concentration. As a result, analyzing gate oxide integrity and dielectric breakdown failures during wafer fabrication becomes more difficult. Using a traditional FA flow and methods some defects were observed after electrical fault isolation using emission microscopic tools such as EMMI and TIVA. Even with some success with conventional FA the root cause was unclear. In this paper, we will propose an analysis flow for GOI failures to improve FA’s success rate. In this new proposed flow both a chemical method, Wright Etch, and SIMS analysis techniques are employed to identify root cause of the GOI failures after EFA fault isolation. In general, the shape of the defect might provide information as to the root cause of the GOI failure, whether related to PID or contamination. However, Wright Etch results are inadequate to answer the questions of whether the failure is caused by contamination or not. If there is a contaminate another technique is required to determine what the contaminant is and where it comes from. If the failure is confirmed to be due to contamination, SIMS is used to further determine the contamination source at the ppm-ppb level. In this paper, a real case of GOI failure will be discussed and presented. Using the new failure analysis flow, the root cause was identified to be iron contamination introduced from a worn out part made of stainless steel.

Advanced IR-OBIRCH Analysis Technique for High Isb Failure Analysis

2010 ◽  
Author(s):  
Kuo Hsiung Chen ◽  
Wen Sheng Wu ◽  
Yu Hsiang Shu ◽  
Jian Chan Lin
Keyword(s):  
Failure Analysis ◽  
Failure Mechanisms ◽  
Fault Localization ◽  
Resistance Change ◽  
The Real ◽  
Analysis Techniques ◽  
Analysis Technique ◽  
Leakage Failure ◽  
Failure Site

Abstract IR-OBIRCH (Infrared Ray – Optical Beam Induced Resistance Change) is one of the main failure analysis techniques [1] [2] [3] [4]. It is a useful tool to do fault localization on leakage failure cases such as poor Via or contact connection, FEoL or BEoL pattern bridge, and etc. But the real failure sites associated with the above failure mechanisms are not always found at the OBIRCH spot locations. Sometimes the real failure site is far away from the OBIRCH spot and it will result in inconclusive PFA Analysis. Finding the real failure site is what matters the most for fault localization detection. In this paper, we will introduce one case using deep sub-micron process generation which suffers serious high Isb current at wafer donut region. In this case study a BEoL Via poor connection is found far away from the OBIRCH spots. This implies that layout tracing skill and relation investigation among OBIRCH spots are needed for successful failure analysis.

Marginal RF Gain Investigation and Root Cause Determination

2013 ◽  
Author(s):  
Keith Harber ◽  
Steve Brockett
Keyword(s):  
Radio Frequency ◽  
Failure Analysis ◽  
Power Amplifier ◽  
Physical Analysis ◽  
Root Cause ◽  
S Parameter ◽  
Mode Of Operation ◽  
S Parameters

Abstract This paper outlines the failure analysis of a Radio Frequency only (RF-only) failure on a complex Multimode Multiband Power Amplifier (MMPA) module, where slightly lower gain was observed in one mode of operation. 2 port S-parameter information was collected and utilized to help localize the circuitry causing the issue. A slight DC electrical difference was observed, and simulation was utilized to confirm that difference was causing the observed S-parameters. Physical analysis uncovered a very visible cause for the RF-only failure.

Contributions of a Formal Analysis Metaprocess to Breakthrough Failure Analysis Results

2003 ◽  
Author(s):  
Steve Ferrier ◽  
Kevin D. Martin ◽  
Donald Schulte
Keyword(s):  
Failure Analysis ◽  
Formal Analysis ◽  
Photon Emission ◽  
Flow Analysis ◽  
Formal Structure ◽  
Ic Design ◽  
Analysis Process ◽  
Secondary Failure ◽  
Leakage Failure ◽  
Wafer Manufacturing

Abstract Application of a formal Failure Analysis metaprocess to a stubborn yield loss problem provided a framework that ultimately facilitated a solution. Absence of results from conventional failure analysis techniques such as PEM (Photon Emission Microscopy) and liquid crystal microthermography frustrated early attempts to analyze this low-level supply leakage failure mode. Subsequently, a reorganized analysis team attacked the problem using a specific toplevel metaprocess.(1,a) Using the metaprocess, analysts generated a specific unique step-by-step analysis process in real time. Along the way, this approach encouraged the creative identification of secondary failure effects that provided repeated breakthroughs in the analysis flow. Analysis proceeded steadily toward the failure cause in spite of its character as a three-way interaction among factors in the IC design, mask generation, and wafer manufacturing processes. The metaprocess also provided the formal structure that, at the conclusion of the analysis, permitted a one-sheet summary of the failure's cause-effect relationships and the analysis flow leading to discovery of the anomaly. As with every application of this metaprocess, the resulting analysis flow simply represented an effective version of good failure analysis. The formal and flexible codification of the analysis decision-making process, however, provided several specific benefits, not least of which was the ability to proceed with high confidence that the problem could and would be solved. This paper describes the application of the metaprocess, and also the key measurements and causeeffect relationships in the analysis.

Failure Analysis of Functional Failures in a Designed for FA SRAM

2004 ◽  
Author(s):  
Gil Garteiz
Keyword(s):  
Failure Analysis ◽  
Success Rate ◽  
Physical Analysis ◽  
Analysis Methodology

Abstract Designing devices for failure analisys (FA) is becoming increasingly critical as structure geometries and killer defects rapidly decrease in size. Naturally, devices that are designed for FA are much easier to analyze and have a higher FA success rate than those that are not. Several analyses of functional failures in a 0.18um CMOS SRAM are presented in this paper to demonstrate “Design For FA” usefulness and application. Physical analysis methodology is also discussed.

The Influence of Optical Beams on Semiconductor Devices During Failure Analysis

2002 ◽  
Author(s):  
Charles Zhang ◽  
Matt Thayer ◽  
Lowell Herlinger ◽  
Greg Dabney ◽  
Manuel Gonzalez
Keyword(s):  
Failure Analysis ◽  
Semiconductor Devices ◽  
Laser Wavelength ◽  
Fault Isolation ◽  
Analysis Techniques ◽  
Cmos Transistor ◽  
Optical Beams

Abstract A number of backside analysis techniques rely on the successful use of optical beams in performing backside fault isolation. In this paper, the authors have investigated the influence of the 1340 nm and 1064 nm laser wavelength on advanced CMOS transistor performance.

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

Sign in / Sign up

Export Citation Format

Share Document