Cavitation Erosion of HVOF Coatings

1996 ◽  
Author(s):  
R. Schwetzke ◽  
H. Kreye
Keyword(s):  
Erosion Rate ◽  
Cavitation Erosion ◽  
Metallic Alloys ◽  
Erosion Mechanism ◽  
Hvof Coatings ◽  
Coating Composition ◽  
Before And After ◽  
Series Of Experiments ◽  
The Individual ◽  
Scanning Electron

Abstract The proposed paper reports a series of experiments to investigate the cavitation erosion mechanism of HVOF coatings. Vibratory cavitation erosion tests according to ASTM G 32 have been carried out with several HVOF coatings including cermets, oxides and metallic alloys. The steady state erosion rate for each coating was determined and the effect of coating composition and microstructure on the erosion rate was investigated. The morphology and microstructure of the various coatings before and after cavitation testing were analyzed by means of light optical and scanning electron microscopy in order to study the erosion mechanism. The results demonstrate that HVOF coatings of NiCrFeBSi, WC-17Co, Cr3C2-25NiCr and Cr2O3 can exhibit a rather high resistance against cavitation erosion and should be considered for application as a protective surface layer against cavitation. Furthermore, it is shown that cavitation testing can provide a useful tool to study and characterize the bond strength between individual splats as well as the brittleness of the individual phases present in the coating.

Assessment of Cavitation Erosion of Gas-Nitrided Cr-Ni-Mo Steels

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Ion Mitelea ◽  
Cristian Ghera ◽  
Ilare Bordeaşu ◽  
Corneliu Crăciunescu
Keyword(s):  
Electron Microscopy ◽  
Erosion Rate ◽  
Structural Changes ◽  
Cavitation Erosion ◽  
Erosion Resistance ◽  
Thermochemical Treatment ◽  
Gas Nitriding ◽  
The Mean ◽  
Cavitation Erosion Resistance ◽  
Scanning Electron

The effect of the gas-nitriding thermochemical treatment on the cavitation erosion resistance of a Cr-Ni-Mo alloy is analyzed using a piezoceramic vibrating equipment and following the ASTM G32-2010 standard. The evaluation of the cavitation erosion behavior was made based on the analysis of the mean depth of erosion (MDE) and mean depth of erosion rate (MDER), for samples subjected to the cavitation erosion for different times. The surface topography and the structural changes in the marginal layer were analyzed through optical and scanning electron microscopy. Following nitriding the cavitation erosion resistance was about 9.6 times higher compared to the annealed state and about 8.2 times higher compared to the hardened and tempered state.

Cavitation Erosion Resistant Coatings Produced by Thermal Spraying and by Weld Cladding

1998 ◽  
Author(s):  
H. Kreye ◽  
R. Schwetzke ◽  
A. Buschinelli ◽  
L. Boccanera
Keyword(s):  
Stainless Steel ◽  
Arc Welding ◽  
Erosion Rate ◽  
Cavitation Erosion ◽  
Thermal Spraying ◽  
Welding Process ◽  
Pulsed Power ◽  
Before And After ◽  
Arc Welding Process ◽  
Weld Cladding

Abstract The cavitation erosion of various hardfacing coatings was investigated by using a vibratory cavitation apparatus according to ASTM G 32. Coatings of austenitic stainless steel containing 10 % cobalt were applied by arc welding. High velocity oxy-fuel spraying (HVOF) was employed to produce coatings of various kinds of cermets and metallic alloys. For each coating, the steady state erosion rate was determined and the effect of process parameters and alloy composition on the microstructure and erosion rate was investigated. The morphology and microstructure of the coatings before and after cavitation testing were analysed by metallographic methods in order to study the erosion mechanism. It is demonstrated that the high resistance to cavitation erosion of the cobalt-alloyed steel can even further increase when the fluxed core arc welding process and an improved pulsed power source are used to produce the coatings. The erosion resistance of the HVOF coatings, however, was limited by pores, microcracks and oxides and did not significantly exceed the level typical for bulk stainless steel 316 L.

Official Advice Improves Mortgage-Holders’ Perceptions of Switching: Experimental Evidence

2019 ◽  
Author(s):  
Shane Timmons
Keyword(s):  
Interest Rate ◽  
Experimental Evidence ◽  
Consumer Protection ◽  
Policy Development ◽  
Switching Process ◽  
Competitive Markets ◽  
Protection Agency ◽  
Change Perceptions ◽  
Before And After ◽  
The Individual

Encouraging consumers to switch to lower-rate mortgages is important both for the individual consumer’s finances and for functioning competitive markets, but switching rates are low. Given the complexity of mortgages, one potential regulatory intervention that may increase switching rates is to provide independent advice on how to select good mortgage products and how to navigate the switching process. Working with a government consumer protection agency, we conducted an experiment with mortgage-holders to test whether such advice alters perceptions of switching. The experiment tested how (i) the attributes of the offer, (ii) perceptions about the switching process, (iii) individual feelings of competence and (iv) comprehension of the product affect willingness to switch to better offers, both before and after reading the official advice. The advice made consumers more sensitive to interest rate decreases, especially at longer terms. It also increased consumers’ confidence in their ability to select good offers. Overall, the findings imply that advice from policymakers can change perceptions and increase switching rates. Moreover, the experiment demonstrates how lab studies can contribute to behaviourally-informed policy development.

Quality of Life for Children with Persistent Sinonasal Symptoms

2003 ◽  
Vol 128 (1) ◽  
pp. 17-26 ◽  
Author(s):  
David J. Kay ◽  
Richard M. Rosenfeld
Keyword(s):  
Quality Of Life ◽  
Clinical Care ◽  
Longitudinal Change ◽  
Good Test ◽  
Routine Clinical Care ◽  
Before And After ◽  
The Mean ◽  
The Individual ◽  
Sinonasal Symptoms

OBJECTIVE: The goal was to validate the SN-5 survey as a measure of longitudinal change in health-related quality of life (HRQoL) for children with persistent sinonasal symptoms. DESIGN AND SETTING: We conducted a before and after study of 85 children aged 2 to 12 years in a metropolitan pediatric otolaryngology practice. Caregivers completed the SN-5 survey at entry and at least 4 weeks later. The survey included 5 symptom-cluster items covering the domains of sinus infection, nasal obstruction, allergy symptoms, emotional distress, and activity limitations. RESULTS: Good test-retest reliability ( R = 0.70) was obtained for the overall SN-5 score and the individual survey items ( R ≥ 0.58). The mean baseline SN-5 score was 3.8 (SD, 1.0) of a maximum of 7.0, with higher scores indicating poorer HRQoL. All SN-5 items had adequate correlation ( R ≥ 0.36) with external constructs. The mean change in SN-5 score after routine clinical care was 0.88 (SD, 1.19) with an effect size of 0.74 indicating good responsiveness to longitudinal change. The change scores correlated appropriately with changes in related external constructs ( R ≥ 0.42). CONCLUSIONS: The SN-5 is a valid, reliable, and responsive measure of HRQoL for children with persistent sinonasal symptoms, suitable for use in outcomes studies and routine clinical care.

scholarly journals General psychopathology links burden of recent life events and psychotic symptoms in a network approach

2020 ◽  
Vol 6 (1) ◽  
Author(s):  
Linda T. Betz ◽  
◽  
Nora Penzel ◽  
Lana Kambeitz-Ilankovic ◽  
Marlene Rosen ◽  
...  
Keyword(s):  
Life Events ◽  
Childhood Trauma ◽  
Negative Symptoms ◽  
Psychotic Symptoms ◽  
Network Approach ◽  
General Psychopathology ◽  
Recent Onset ◽  
Syndrome Scale ◽  
Before And After ◽  
The Individual

AbstractRecent life events have been implicated in the onset and progression of psychosis. However, psychological processes that account for the association are yet to be fully understood. Using a network approach, we aimed to identify pathways linking recent life events and symptoms observed in psychosis. Based on previous literature, we hypothesized that general symptoms would mediate between recent life events and psychotic symptoms. We analyzed baseline data of patients at clinical high risk for psychosis and with recent-onset psychosis (n = 547) from the Personalised Prognostic Tools for Early Psychosis Management (PRONIA) study. In a network analysis, we modeled links between the burden of recent life events and all individual symptoms of the Positive and Negative Syndrome Scale before and after controlling for childhood trauma. To investigate the longitudinal associations between burden of recent life events and symptoms, we analyzed multiwave panel data from seven timepoints up to month 18. Corroborating our hypothesis, burden of recent life events was connected to positive and negative symptoms through general psychopathology, specifically depression, guilt feelings, anxiety and tension, even after controlling for childhood trauma. Longitudinal modeling indicated that on average, burden of recent life events preceded general psychopathology in the individual. In line with the theory of an affective pathway to psychosis, recent life events may lead to psychotic symptoms via heightened emotional distress. Life events may be one driving force of unspecific, general psychopathology described as characteristic of early phases of the psychosis spectrum, offering promising avenues for interventions.

scholarly journals Effect of Nitrogen Ion Implantation on the Cavitation Erosion Resistance and Cobalt-Based Solid Solution Phase Transformations of HIPed Stellite 6

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2324
Author(s):  
Mirosław Szala ◽  
Dariusz Chocyk ◽  
Anna Skic ◽  
Mariusz Kamiński ◽  
Wojciech Macek ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Ion Implantation ◽  
Phase Transformations ◽  
Erosion Rate ◽  
Cavitation Erosion ◽  
Matrix Phase ◽  
Nitrogen Ion Implantation ◽  
Stellite 6 ◽  
Nitrogen Ion

From the wide range of engineering materials traditional Stellite 6 (cobalt alloy) exhibits excellent resistance to cavitation erosion (CE). Nonetheless, the influence of ion implantation of cobalt alloys on the CE behaviour has not been completely clarified by the literature. Thus, this work investigates the effect of nitrogen ion implantation (NII) of HIPed Stellite 6 on the improvement of resistance to CE. Finally, the cobalt-rich matrix phase transformations due to both NII and cavitation load were studied. The CE resistance of stellites ion-implanted by 120 keV N+ ions two fluences: 5 × 1016 cm−2 and 1 × 1017 cm−2 were comparatively analysed with the unimplanted stellite and AISI 304 stainless steel. CE tests were conducted according to ASTM G32 with stationary specimen method. Erosion rate curves and mean depth of erosion confirm that the nitrogen-implanted HIPed Stellite 6 two times exceeds the resistance to CE than unimplanted stellite, and has almost ten times higher CE reference than stainless steel. The X-ray diffraction (XRD) confirms that NII of HIPed Stellite 6 favours transformation of the ε(hcp) to γ(fcc) structure. Unimplanted stellite ε-rich matrix is less prone to plastic deformation than γ and consequently, increase of γ phase effectively holds carbides in cobalt matrix and prevents Cr7C3 debonding. This phenomenon elongates three times the CE incubation stage, slows erosion rate and mitigates the material loss. Metastable γ structure formed by ion implantation consumes the cavitation load for work-hardening and γ → ε martensitic transformation. In further CE stages, phases transform as for unimplanted alloy namely, the cavitation-inducted recovery process, removal of strain, dislocations resulting in increase of γ phase. The CE mechanism was investigated using a surface profilometer, atomic force microscopy, SEM-EDS and XRD. HIPed Stellite 6 wear behaviour relies on the plastic deformation of cobalt matrix, starting at Cr7C3/matrix interfaces. Once the Cr7C3 particles lose from the matrix restrain, they debond from matrix and are removed from the material. Carbides detachment creates cavitation pits which initiate cracks propagation through cobalt matrix, that leads to loss of matrix phase and as a result the CE proceeds with a detachment of massive chunk of materials.

Adaptive Precision Block-Jacobi for High Performance Preconditioning in the Ginkgo Linear Algebra Software

2021 ◽  
Vol 47 (2) ◽  
pp. 1-28
Author(s):  
Goran Flegar ◽  
Hartwig Anzt ◽  
Terry Cojean ◽  
Enrique S. Quintana-Ortí
Keyword(s):  
Linear Algebra ◽  
Graphics Processing Units ◽  
High Performance ◽  
Numerical Algorithms ◽  
Mixed Precision ◽  
Before And After ◽  
Memory Accesses ◽  
Specialized Hardware ◽  
The Individual ◽  
Graphics Processing

The use of mixed precision in numerical algorithms is a promising strategy for accelerating scientific applications. In particular, the adoption of specialized hardware and data formats for low-precision arithmetic in high-end GPUs (graphics processing units) has motivated numerous efforts aiming at carefully reducing the working precision in order to speed up the computations. For algorithms whose performance is bound by the memory bandwidth, the idea of compressing its data before (and after) memory accesses has received considerable attention. One idea is to store an approximate operator–like a preconditioner–in lower than working precision hopefully without impacting the algorithm output. We realize the first high-performance implementation of an adaptive precision block-Jacobi preconditioner which selects the precision format used to store the preconditioner data on-the-fly, taking into account the numerical properties of the individual preconditioner blocks. We implement the adaptive block-Jacobi preconditioner as production-ready functionality in the Ginkgo linear algebra library, considering not only the precision formats that are part of the IEEE standard, but also customized formats which optimize the length of the exponent and significand to the characteristics of the preconditioner blocks. Experiments run on a state-of-the-art GPU accelerator show that our implementation offers attractive runtime savings.

scholarly journals Micromagnetic Characterization of Operation-Induced Damage in Charpy Specimens of RPV Steels

2021 ◽  
Vol 11 (7) ◽  
pp. 2917
Author(s):  
Madalina Rabung ◽  
Melanie Kopp ◽  
Antal Gasparics ◽  
Gábor Vértesy ◽  
Ildikó Szenthe ◽  
...  
Keyword(s):  
Neutron Irradiation ◽  
Pressure Vessel ◽  
Operating Conditions ◽  
Magnetic Characteristics ◽  
Pressure Vessel Steel ◽  
Training Procedure ◽  
Vessel Steel ◽  
Before And After ◽  
The Individual ◽  
Magnetic Adaptive Testing

The embrittlement of two types of nuclear pressure vessel steel, 15Kh2NMFA and A508 Cl.2, was studied using two different methods of magnetic nondestructive testing: micromagnetic multiparameter microstructure and stress analysis (3MA-X8) and magnetic adaptive testing (MAT). The microstructure and mechanical properties of reactor pressure vessel (RPV) materials are modified due to neutron irradiation; this material degradation can be characterized using magnetic methods. For the first time, the progressive change in material properties due to neutron irradiation was investigated on the same specimens, before and after neutron irradiation. A correlation was found between magnetic characteristics and neutron-irradiation-induced damage, regardless of the type of material or the applied measurement technique. The results of the individual micromagnetic measurements proved their suitability for characterizing the degradation of RPV steel caused by simulated operating conditions. A calibration/training procedure was applied on the merged outcome of both testing methods, producing excellent results in predicting transition temperature, yield strength, and mechanical hardness for both materials.

scholarly journals Redox Mechanism of Azathioprine and Its Interaction with DNA

2021 ◽  
Vol 22 (13) ◽  
pp. 6805
Author(s):  
Mihaela-Cristina Bunea ◽  
Victor-Constantin Diculescu ◽  
Monica Enculescu ◽  
Horia Iovu ◽  
Teodor Adrian Enache
Keyword(s):  
Electron Microscopy ◽  
Mass Spectrometry ◽  
Scanning Electron Microscopy ◽  
Structural Changes ◽  
Differential Pulse ◽  
Immunosuppressive Drug ◽  
Redox Mechanism ◽  
Before And After ◽  
Dna Film ◽  
Scanning Electron

The electrochemical behavior and the interaction of the immunosuppressive drug azathioprine (AZA) with deoxyribonucleic acid (DNA) were investigated using voltammetric techniques, mass spectrometry (MS), and scanning electron microscopy (SEM). The redox mechanism of AZA on glassy carbon (GC) was investigated using cyclic and differential pulse (DP) voltammetry. It was proven that the electroactive center of AZA is the nitro group and its reduction mechanism is a diffusion-controlled process, which occurs in consecutive steps with formation of electroactive products and involves the transfer of electrons and protons. A redox mechanism was proposed and the interaction of AZA with DNA was also investigated. Morphological characterization of the DNA film on the electrode surface before and after interaction with AZA was performed using scanning electron microscopy. An electrochemical DNA biosensor was employed to study the interactions between AZA and DNA with different concentrations, incubation times, and applied potential values. It was shown that the reduction of AZA molecules bound to the DNA layer induces structural changes of the DNA double strands and oxidative damage, which were recognized through the occurrence of the 8-oxo-deoxyguanosine oxidation peak. Mass spectrometry investigation of the DNA film before and after interaction with AZA also demonstrated the formation of AZA adducts with purine bases.

Acquiring variable commands at home and abroad: Examining optatives and imperatives in L1 and L2 Spanish

2020 ◽  
Vol 13 (1) ◽  
pp. 79-113
Author(s):  
Farrah Neumann ◽  
Matthew Kanwit
Keyword(s):  
Second Language ◽  
Second Language Acquisition ◽  
Study Abroad ◽  
Language Teaching ◽  
Applied Linguistics ◽  
Future Research ◽  
Control Group ◽  
Before And After ◽  
The Individual ◽  
At Home

AbstractSince many linguistic structures are variable (i. e. conveyed by multiple forms), building a second-language grammar critically involves developing sociolinguistic competence (Canale and Swain. 1980. Theoretical bases of communicative approaches to second language teaching and testing. Applied Linguistics 1(1). 1–47), including knowledge of contexts in which to use one form over another (Bayley and Langman. 2004. Variation in the group and the individual: Evidence from second language acquisition. International Review of Applied Linguistics in Language Teaching 42(4). 303–318). Consequently, researchers interested in such competence have increasingly analyzed the study-abroad context to gauge learners’ ability to approximate local norms following a stay abroad, due to the quality and quantity of input to which learners may gain access (Lafford. 2006. The effects of study abroad vs. classroom contexts on Spanish SLA: Old assumptions, new insights and future research directions. In Carol Klee & Timothy Face (eds.), Selected proceedings of the 7th conference on the acquisition of Spanish and Portuguese as first and second languages, 1–25. Somerville, MA: Cascadilla Proceedings Project). Nevertheless, the present study is the first to examine native or learner variation between imperative (e. g. ven ‘come’) and optative Spanish commands (e. g. que vengas ‘come’). We first performed a corpus analysis to determine the linguistic factors to manipulate in a contextualized task, which elicited commands from learners before and after four weeks abroad in Alcalá de Henares, Spain. Their overall rates of selection and predictive factors were compared to local native speakers (NSs) and a control group of at-home learners.Results revealed that the abroad learners more closely approached NS rates of selection following the stay abroad. Nonetheless, for both learner groups conditioning by independent variables only partially approximated the NS system, which was more complex than previously suggested.

Sign in / Sign up

Export Citation Format

Share Document