scholarly journals Approximate Representation and Exposition of ISI Flat Plate Collector including Revised Flat Plate Collector : A Review

2020 ◽  
pp. 345-350
Author(s):  
Rajeshkumar U. Sambhe ◽  
Sagar S. Gaddamwar
Keyword(s):  
Flat Plate ◽  
Natural Circulation ◽  
Renewable Energy Sources ◽  
Tube Length ◽  
Outlet Temperature ◽  
Solar Collectors ◽  
Pv System ◽  
Comparative Performance ◽  
Low Efficiency ◽  
Flat Plate Collector

Cosmic power is one of the numerous renewable energy sources that can use in a Photovoltaic (PV) system or Thermal. Solar collectors play a crucial role in solar thermal systems. They convert solar radiation into heat and transfer the heat to working fluids Such as water or air. The Flat-plate collectors are the numerous common type of solar collectors and typically used as a water heater or air heater. These collectors have low efficiency and low outlet temperature. Recently, many scientists have attempted to improve the efficiency and performance of flat-plate collectors via different methods. This review paper describes the results of the experimentation carried out to study and compare the performance of the modified flat plate collector having increasing riser tube diameter and reducing riser tube length with the conventional ISI marked solar liquid flat plate collector. To study, the comparative performance characteristics of a modified flat plate collector with ISI flat plate collector operated under natural circulation mode. The suggested design found to be better than the existing ISI design of the absorber plate from an efficiency point of view. The actual useful heat gain (Qu) in the suggested design understudy found to be more by 30% than that in the case of ISI collector. However, the modified flat plate collector found to operate at a relatively lower exit temperature than the conventional ISI marked collector.

Performance Comparison of Flat Plate Collectors Fitted With Non Circular Risers With Integral Fins

2005 ◽  
Author(s):  
V. R. Bhore ◽  
S. B. Thombre
Keyword(s):  
Flat Plate ◽  
Unit Area ◽  
Natural Circulation ◽  
Performance Comparison ◽  
Test Results ◽  
Absorber Plate ◽  
Circulation Mode ◽  
Induced Flow ◽  
Flat Plate Collector ◽  
Buoyancy Induced Flow

The present study deals with comparison of experimentally determined performance characteristics of solar flat plate collectors fitted with novel designs of absorber plate involving non-circular risers with integral fins and operating under natural circulation mode. The main flow passages considered were square, triangular and semicircular in cross section. One standard solar flat plate collector with circular risers was also tested simultaneously for direct comparison. The test results indicate that the absorber fitted with the triangular sectioned risers yields the best performance in terms of the efficiency (63%), and the buoyancy induced flow per unit area (76 kg/hr-m2) from amongst the collectors investigated. It is followed by the absorbers fitted with the semicircular and square sectioned risers respectively. The standard solar flat plate collector is found to yield the lowest values i.e. 46 % and 40 kg/hr-m2 respectively.

A Fundamental Equation for Exergy Balance on Solar Collectors

1988 ◽  
Vol 110 (2) ◽  
pp. 102-106 ◽  
Author(s):  
Akio Suzuki
Keyword(s):  
Flat Plate ◽  
Balance Equation ◽  
Solar Collector ◽  
Fundamental Equation ◽  
Thermal Design ◽  
Optimum Operating ◽  
Solar Collectors ◽  
Optimum Operating Condition ◽  
Flat Plate Collector ◽  
Exergy Balance

This paper presents the exergy balance equation on a solar collector which acts as the fundamental and principal expression for the solar thermal design. The equation fully explains the exergy loss processes and can be used to derive the approximate optimum operating condition for solar collectors. Furthermore, using the equation, it can be shown that two different collectors, an evacuated tubular collector and a flat-plate collector, have both nearly equal capabilities in exergy gain despite large differences in technological efforts and expenses to produce them. In addition, ways for improvement for a solar collector are also discussed here briefly.

Energetic and Exergetic Performance of a Solar Flat-Plate Collector Working With Cu Nanofluid

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
SeyedReza Shamshirgaran ◽  
Morteza Khalaji Assadi ◽  
Hussain H. Al-Kayiem ◽  
Korada Viswanatha Sharma
Keyword(s):  
Flat Plate ◽  
Convection Heat Transfer ◽  
Computer Code ◽  
Energetic Efficiency ◽  
Outlet Temperature ◽  
Pressure Losses ◽  
Overall Performance ◽  
Flat Plate Collector ◽  
Practical Geometry ◽  
Internal Convection

The evaluation of the performance and characteristics of a solar flat-plate collector (FPC) are reported for domestic and industrial requirements in the existing literature. A computer code was developed using matlab to model and evaluate the energetic and exergetic performance of a nanofluid-based FPC for steady-state and laminar conditions. The analysis was performed using practical geometry data, especially the absorber emittance, for a standard collector. Linear pressure losses in manifolds were taken into account, and a more accurate exergy factor corresponding to a correct value of 5770 K for the sun temperature was employed. The results demonstrate that copper–water nanofluid has the potential to augment the internal convection heat transfer coefficient by 76.5%, and to enhance the energetic efficiency of the collector from 70.3% to 72.1% at 4% volume concentration, when compared to the values with water. Additionally, it was revealed that copper nanofluid is capable of increasing the collector fluid's outlet temperature and decreasing the absorber plate's mean temperature by 3 K. The addition of nanoparticles to the water demonstrated a reduction in the total entropy generation by the solar FPC. Furthermore, increasing the nanoparticle size reflected a reduction in the overall performance of the solar collector.

Design and Analysis of Solar Tracking System for Multipurpose Domestic Applications

2013 ◽  
Author(s):  
P. Rhushi Prasad ◽  
P. B. Gangavati ◽  
H. V. Byregowda ◽  
K. S. Badarinarayan
Keyword(s):  
Solar Energy ◽  
Energy Conversion ◽  
Flat Plate ◽  
Tracking System ◽  
Solar Collectors ◽  
Tracking Systems ◽  
Pv Panel ◽  
Energy Conversion Systems ◽  
Flat Plate Collector ◽  
Parabolic Collector

Now-a-days the field of applied mechanical systems opens new horizons for the use of orientation mechanisms. The opportunity to use mechanisms with a “sustainable purpose” leads to new approaches in the development of renewable energy systems design. The evaluation of the existing products shows that the tracking mechanisms for solar energy conversion systems may improve the efficiency of the solar energy conversion systems up to 30% to 50%. Applications of solar energy for domestic and industrial heating purposes have been becoming very popular. However the effectiveness of presently used fixed flat plate collectors, PV panels and parabolic collector are low due to the moving nature of the energy source. The presents research was carried out in the field of increasing the efficiency of the solar energy received by the solar collectors like PV panels, Flat plate collectors, Cylindrical Parabolic collectors using tracking systems by changing the position of the solar collectors correlated to the sun position for getting maximum radiation use of beam radiation falling on the solar collector. Two main aspects are taken into consideration, one optimizing the interaction between the mechatronic system components by integrating the analog electronic system by using a 555 timer in the mechanical model, and secondly by reducing the cost & time for the design process. The research work was carried out for location in chickballapur district at BGS R&D centre in Karnataka State, India. The results obtained in work is 24% increase in tracking efficiency of experimental model of flat plate collector, 30% increase in tracking efficiency in working model flat plate collector, 39 % increase in tracking efficiency of cylindrical parabolic collector and 36% increases in tracking efficiency of the Photovoltaic panel is found when compared to the non-tracking systems respectively. This paper presents the results of PV panel collector in detail for increasing the efficiency of the PV panel collector by tracking system with comparison of non-tracking system.

Predicted Efficiency of a Nanofluid-Based Direct Absorption Solar Receiver

2007 ◽  
Author(s):  
Himanshu Tyagi ◽  
Patrick Phelan ◽  
Ravi Prasher
Keyword(s):  
Flat Plate ◽  
Pure Water ◽  
Incident Radiation ◽  
Operating Conditions ◽  
Heat Transfer Analysis ◽  
Working Fluid ◽  
Direct Absorption ◽  
Low Efficiency ◽  
Flat Plate Collector ◽  
Solar Receiver

Due to its renewable and non-polluting nature solar energy is often used in applications such as electricity generation, thermal heating and chemical processing. The most cost-effective solar heaters are of the “flat-plate” type, but these suffer from relatively low efficiency and outlet temperatures. The present study theoretically investigates the feasibility of using a direct absorption solar receiver (DAR) and compares its performance with that of a typical flat-plate collector. Here a nanofluid—a mixture of water and aluminum nanoparticles—is used as the absorbing medium. A two-dimensional heat transfer analysis was developed in which direct sunlight was incident on a thin flowing film of nanofluid. The effects of absorption and scattering within the nanofluid were accounted for. In order to evaluate the temperature profile and intensity distribution within the nanofluid the energy balance equation and heat transport equation were solved numerically. It was observed that the presence of nanoparticles increases the absorption of incident radiation by more than 9 times over that of pure water. According to the results obtained from this study, under similar operating conditions, the efficiency of a DAR using nanofluid as the working fluid is found to be up to 10% higher (on an absolute basis) than that of a flat-plate collector.

scholarly journals Feasibility Analysis and Performance Evaluation and Optimization of a DXSAHP Water Heater Based on the Thermal Capacity of the System: A Case Study

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3883
Author(s):  
Jorge E. De León-Ruiz ◽  
Ignacio Carvajal-Mariscal ◽  
Antonin Ponsich
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Heat Pump ◽  
Thermal Capacity ◽  
Hot Water ◽  
Outlet Temperature ◽  
Solar Collectors ◽  
Pump System ◽  
Heat Pump System

The present work conducts an evaluation of the feasibility and the overall performance and consequent optimization of a direct expansion solar assisted heat pump (DXSAHP) employed for domestic water heating. For the study conducted R134a, R404A, R407C and R410A working fluids were evaluated as well as the use of four, six and eight flat-plate solar collectors and a worktime ranging from 1 to 6 h. The case study is based in Mexico City with a 300 L container and a hot water outlet temperature of 51 °C. The paper introduces a new evaluation criterion based on the thermal capacity and all the evaluations conducted throughout this research revolve around this performance metric. The results show that, the system would require at least 4 h of operation to achieve the outlet temperature. Additionally, it was found that the R410A refrigerant has the best heat transfer properties; with an average condensation heat rate of 6.31 kW, followed by the R407C with 5.72 kW, the R404A with 5.42 kW and the R134a with 5.18 kW. Diversely, the R134a refrigerant requires 0.402 kW of compression work, 62% less than the R410A, which requires 1.06 kW. Consequently, R134a delivers the highest COP, which ranges from 7 to 14, followed by the R407C and R404A refrigerants, which present a similar behaviour between them, with COP ranging from 5 to 9 and 4 to 8, respectively, and finally the R410A, achieving the lowest COP, ranging from 3.5 to 6.5. Moreover, it was found that the R134a presents a higher dispersion regarding the energy exchange rate, which reveals that it is the fluid most susceptible to external factors, such as the weather. Contrarily, the remaining refrigerants present a more consistent performance. Finally, the optimization revealed that the R407C refrigerant is the most suitable given that it requires 20% less compression work than the R404A. This provides the heat pump system with a steadier behaviour, a COP ranging from 7 to 8, 30% higher than R410A, a worktime decrease of 1.5 h and heat transfer area of 5.5 flat-plate solar collectors, equivalent to a 31% reduction, both compared to R134a.

scholarly journals Three-dimensional Analysis of Air Flow in a Flat Plate Solar Collector

2018 ◽  
Author(s):  
Mohammed Amine Amraoui ◽  
Khaled Aliane
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flat Plate ◽  
Solar Collector ◽  
Three Dimensional ◽  
Outlet Temperature ◽  
Computational Fluid Dynamics Cfd ◽  
Flat Plate Collector ◽  
Work Done

This paper presents the study of fluid flow and heat transfer in solar flat plate collector by using Computational Fluid Dynamics (CFD) which reduces time and cost. In the present paper the computational fluid dynamics (CFD) tool has been used to simulate the solar collector for better understanding the heat transfer capability. 3D model of the collector involving air inlet, the collector is modeled by ANSYS Workbench and the grid was created in ANSYS ICEM. The results were obtained by using ANSYS FLUENT and ANSYS CFX. The objective of this work is to compare theoretically and experimentally work done with the work done by using computational fluid dynamics (CFD) tool with respect to flow and temperature distribution inside the solar collector. The outlet temperature of air is compared with experimental results and there is a good agreement in between them.

scholarly journals Performance Estimation of Solar Flat Plate Air Heating System Using Helical Tapes

2019 ◽  
Vol 6 ◽  
Author(s):  
Jeson Wilson John ◽  
Ashwin Harikrishnan
Keyword(s):  
Flat Plate ◽  
Convective Heat Transfer Coefficient ◽  
Heating System ◽  
Performance Estimation ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Absorber Plate ◽  
Air Heating ◽  
Temperature Efficiency ◽  
Flat Plate Collector

Solar flat plate collectors (FPC) are used for heating spaces, water heating, and many other purposes. The present technology of solar flat collectors uses vertical fins. The solar flat plate collector having absorber with vertical fins is provided with a helical tape in the fluid flow path. The absorber plate in the solar flat plate collector has an area of 100 cm x 50 cm. The solar flat plate collector has nine ducts with an area of 27.5 cm x 9.5 cm each. The helical tapes attached have a start angle of 64 deg which pass along the whole length of the duct. The helical tapes have a crosssection area of 1.5 mm x 4 mm. The pitch of the helical tapes is 100 mm. These fins have been attached between the vertical fins of the thickness of 1mm and a height of 10.5 cm. Data such as inlet temperature, outlet temperature efficiency and convective heat transfer coefficient are calculated. The mass flow rate of air is 10.28 kg/s and the air is subjected to solar radiation between 628.98 W/m2 and 708.59 W/m2. The values are noted down, and the and the efficiency is noted to have a 10% rise. The effectiveness of the solar plate collector will increase using a helical fin. A comparative analysis will be done between the conventional flat plate collector and the setup with the helical tapes. The study will show that the helical tapes in flat plate collector will be the best alternative compared to conventional flat plate collector.

A Review on the Use of Hybrid Nanofluid in a Solar Flat Plate and Parabolic Trough Collectors and Its Enhanced Collector Thermal Efficiency

2021 ◽  
Vol 10 (2) ◽  
pp. 147-171
Author(s):  
L. Syam Sundar ◽  
Solomon Mesfin ◽  
Yihun Tefera Sintie ◽  
V. Punnaiah ◽  
Ali J. Chamkha ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Flat Plate ◽  
Thermal Efficiency ◽  
Energy Demand ◽  
Fossil Fuel ◽  
Working Fluid ◽  
Solar Collectors ◽  
The World ◽  
Hybrid Nanofluids ◽  
Flat Plate Collector

Energy demand is high in all parts of the world, mostly in all industrial sectors. To meet the energy demand the fossil fuel is the only way. Due to rapid industrial growth and use of fossil fuel result in global warming and environmental pollution. Moreover, the limited availability of the fossil fuels, it is necessary to depend on the renewable energy sources. Promising renewable energy in the world is solar energy, which is available largely on the earth surface. The solar energy can be converted into thermal energy in the solar flat plate collector. The collector thermal efficiency is purely depends on the working fluid used in it. Most of the studies revealed that replacing the working fluid with high thermal conductivity fluids called as nanofluids and hybrid nanofluids can improve the collector thermal efficiency. Few decades back studies have been conducted with nanofluids in solar collectors. Currently the researchers are working on solar collectors for further improvement of its efficiency using hybrid nanofluids. In this review paper, we will discuss about the synthesis of hybrid nanoparticles, hybrid nanofluids, characterization, thermophysical properties, and application of hybrid nanofluids in solar flat plate collector under natural and forced circulation of fluid. The research gap in the solar collector is also discussed in this article. This paper also explains about the heat transfer capabilities of hybrid nanofluids especially used solar collectors.

Sign in / Sign up

Export Citation Format

Share Document