scholarly journals Cutting Characteristics and Layout of Pre-cutting Machine Cutter

2020 ◽  
Author(s):  
Xuhui Zhang ◽  
Jianmin Li ◽  
Yimin Xia ◽  
Laikuang Lin ◽  
Mi Li ◽  
...  
Keyword(s):  
Cutting Force ◽  
Specific Energy ◽  
Normal Force ◽  
Rock Breaking ◽  
Cutting Efficiency ◽  
Cutting Depth ◽  
Continuous Increase ◽  
Research Results ◽  
Cutting Machine ◽  
Depth Increase

The pre-cutting machine is becoming valued due to its ability to effectively prevent surface settlement and reduce vibration in tunnel construction. To obtain the cutting characteristics and layout of pre-cutting machine cutter, the cutting tests by the pre-cutting machine cutter are conducted and the cutting laws are also studied. The research results show that the cutting force rather than normal force and side force is responsible for the rock breaking. With the increase of the cutting depth and cutting spacing, the cutting forces increase generally. But for the little value of cutting spacing, the cutting force can not increase continuously when the cutting depth increase to a relatively large value. Furthermore, for a given cutting depth, the cutting force will keep at an approximate constant rather than continuous increase with the increase of the cutting spacing when the cutting spacing increases to a relatively large value. The specific energy decreases nonlinearly with the increase of cutting depth and the decrease of specific energy is not significant when the cutting depth is more than 12 mm. Moreover, there exists an optimal cutting spacing for a given cutting depth. To maintain a desirable cutting efficiency, the ratio of cutting spacing to cutting depth should be controlled between 1 and 2. Finally, the layout plan of the pre-cutting machine cutter is proposed based on the research results and is applied in the actual manufacturing of the pre-cutting machine.

scholarly journals Numerical Investigation of the Rock Cutting Performance of a Circular Sawblade

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Zhiwen Wang ◽  
Qingliang Zeng ◽  
Zhenguo Lu ◽  
Zhihai Liu ◽  
Xu Li
Keyword(s):  
Cutting Force ◽  
Great Influence ◽  
Cutting Parameters ◽  
Simulation Method ◽  
Rock Cutting ◽  
Rock Breaking ◽  
Feed Speed ◽  
Specific Cutting Energy ◽  
Cutting Depth ◽  
Cutting Energy

The rock cutting process with a circular sawblade and the rock breaking mechanism of rock are studied with a numerical simulation method in this paper. The influence of cutting parameters of the circular sawblade on cutting force, rock damage, and specific cutting energy in the process of circular sawblade cutting rock is researched. The cutting force increases with the feed speed and an increase in cutting depth and decline in rotation speed. Cutting rock with double circular sawblades can reduce cutting force. However, the specific cutting energy declines with the increase in cutting depth and the decline in the distance between the double circular sawblades. Cutting parameters have a great influence on the damage range of rock. The research results can be applied to rock processing with a circular sawblade.

scholarly journals Investigation of the Cross-Cutting Polycrystalline Diamond Compact Bit Drilling Efficiency

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Chun-Liang Zhang ◽  
Ying-Xin Yang ◽  
Hai-Tao Ren ◽  
Can Cai ◽  
Yong Liu ◽  
...  
Keyword(s):  
Cutting Force ◽  
Polycrystalline Diamond ◽  
Rock Breaking ◽  
The Novel ◽  
Cutting Efficiency ◽  
Bottom Hole ◽  
Pdc Bit ◽  
The Cross ◽  
Polycrystalline Diamond Compact ◽  
Cutting Modes

The parallel track scraping principle of conventional PDC bits largely limits the cutting efficiency and working life in deep formations. Cross-cutting polycrystalline diamond compact (PDC) bit may be an efficient drilling tool that increases the rock-breaking efficiency through both cross-cutting and alternate-cutting modes of the PDC cutter. The motion track equation of the cross-cutting PDC bit was derived by using the compound coordinate system, and the motion track was analyzed. Meanwhile, through the unit experiment and discrete element simulation, the cutting force, volume-specific load, and crack propagation were analyzed under different cutting modes. Through establishing a nonlinear dynamic model of the bit-rock system, the speed-up mechanism of the novel bit was analyzed based on rock damage, rock stress state, and motion characteristic of the bit during the rock-breaking process. Compared with unidirectional cutting, cross-cutting produces less cutting force, more brittle fracture, and a greater decrease of formation strength. The novel PDC bit can put more rock elements into a tensile stress condition than a conventional PDC bit, and the plastic energy dissipation ratio of the cross-cutting PDC bit is lower while the damage energy consumption ratio is higher than they are for conventional bits, which is beneficial to increasing the ratio of fracture failure and improving rock-breaking efficiency. Laboratory drilling tests show that the cross-cutting PDC bit can create mesh-like bottom-hole features. Drilling contrast experiments show that a mesh-like bottom-hole pattern can be obtained by using the cross-cutting PDC bit, of which the ROP is obviously higher than that of the conventional bit when drilling in sandstone or limestone formation. Meanwhile, the influence of deviation angle, weight on bit, and rock properties on cutting efficiency of the cross-cutting PDC bit are studied.

scholarly journals Effect of Water-Based Nanolubricants in Ultrasonic Vibration Assisted Grinding

2018 ◽  
Vol 2 (4) ◽  
pp. 80 ◽  
Author(s):  
Mir Molaie ◽  
Ali Zahedi ◽  
Javad Akbari
Keyword(s):  
Surface Roughness ◽  
Specific Energy ◽  
Material Removal ◽  
Normal Force ◽  
Tangential Force ◽  
Process Efficiency ◽  
Multiwall Carbon Nanotube ◽  
Ultrasonic Vibrations ◽  
Mql Grinding ◽  
Water Based

Currently, because of stricter environmental standards and highly competitive markets, machining operations, as the main part of the manufacturing cycle, need to be rigorously optimized. In order to simultaneously maximize the production quality and minimize the environmental issues related to the grinding process, this research study evaluates the performance of minimum quantity lubrication (MQL) grinding using water-based nanofluids in the presence of horizontal ultrasonic vibrations (UV). In spite of the positive impacts of MQL using nanofluids and UV which are extensively reported in the literature, there is only a handful of studies on concurrent utilization of these two techniques. To this end, for this paper, five kinds of water-based nanofluids including multiwall carbon nanotube (MWCNT), graphite, Al2O3, graphene oxide (GO) nanoparticles, and hybrid Al2O3/graphite were employed as MQL coolants, and the workpiece was oscillated along the feed direction with 21.9 kHz frequency and 10 µm amplitude. Machining forces, specific energy, and surface quality were measured for determining the process efficiency. As specified by experimental results, the variation in the material removal nature made by ultrasonic vibrations resulted in a drastic reduction of the grinding normal force and surface roughness. In addition, the type of nanoparticles dispersed in water had a strong effect on the grinding tangential force. Hybrid Al2O3/graphite nanofluid through two different kinds of lubrication mechanisms—third body and slider layers—generated better lubrication than the other coolants, thereby having the lowest grinding forces and specific energy (40.13 J/mm3). It was also found that chemically exfoliating the graphene layers via oxidation and then purification prior to dispersion in water promoted their effectiveness. In conclusion, UV assisted MQL grinding increases operation efficiency by facilitating the material removal and reducing the use of coolants, frictional losses, and energy consumption in the grinding zone. Improvements up to 52%, 47%, and 61%, respectively, can be achieved in grinding normal force, specific energy, and surface roughness compared with conventional dry grinding.

Experimental Examination of the Impact of Tool Radius on Specific Energy in Microcutting of Granite

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Miloš Pjević ◽  
Ljubodrag Tanović ◽  
Goran Mladenović ◽  
Biljana Marković
Keyword(s):  
Cutting Force ◽  
Penetration Depth ◽  
Specific Energy ◽  
Brittle Materials ◽  
Experimental Examination ◽  
Workpiece Surface ◽  
Different Shapes ◽  
Tip Radius ◽  
The Impact ◽  
Force Intensity

The paper presents experimental results of microcutting brittle materials (granite). The analysis was conceived on the observed interaction between the workpiece and two tools of different shapes. Experiment was based on scratching the workpiece surface with diamond tools. Applied tools had tip radius R0.2 and R0.15 mm. The experiment determined the changes in the value of perpendicular and tangential components of the cutting force based on the geometric properties of tools, as well as the changes of the specific energy of microcutting granite (Jošanica and Bukovik types). The experiment has shown that reduction of tool radius causes reduction of the cutting force intensity and specific cutting energy. Because of its physical/mechanical properties, more energy is required for micromachining granite “Jošanica” than “Bukovik.” Based on the topography of the surface, the value of critical tool penetration depth was established, after which the brittle fracture is no longer present. For granite “Jošanica” values of critical penetration depth are 6 and 5 μm when micromachining with tools R0.2 and R0.15 mm, while for Bukovik those values are 6.5 and 5.5 μm. The paper should form the basis for understanding the phenomena which occur during microcutting brittle materials.

Limitations of an Indentation Model for Grinding Gamma Titanium Aluminide

2002 ◽  
Author(s):  
H. Ali Razavi ◽  
Steven Danyluk ◽  
Thomas R. Kurfess
Keyword(s):  
Force Control ◽  
Titanium Aluminide ◽  
Normal Force ◽  
Removal Rate ◽  
Cubic Boron Nitride ◽  
Normal Component ◽  
Grinding Force ◽  
Cutting Depth ◽  
Gamma Titanium Aluminide ◽  
Gamma Titanium

This paper explores the limitations of a previously reported indentation model that correlated the depth of plastic deformation and the normal component of the grinding force. The indentation model for grinding is studied using force control grinding of gamma titanium aluminide (TiAl-γ). Reciprocating surface grinding is carried out for a range of normal force 15–90 N, a cutting depth of 20–40 μm and removal rate of 1–9 mm3/sec using diamond, cubic boron nitride (CBN) and aluminum oxide (Al2O3) abrasives. The experimental data show that the indentation model for grinding is a valid approximation when the normal component of grinding force exceeds some value that is abrasive dependent.

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool

2014 ◽  
Vol 800-801 ◽  
pp. 237-240
Author(s):  
Li Fu Xu ◽  
Ze Liang Wang ◽  
Shu Tao Huang ◽  
Bao Lin Dai
Keyword(s):  
Experimental Study ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Cbn Tool ◽  
Cutting Experiment ◽  
Rough Turning

In this paper, the cutting experiment was used to study the influence of various cutting parameters on cutting force when rough turning titanium alloy (TC4) with the whole CBN tool. The results indicate that among the cutting speed, feed rate and cutting depth, the influence of the cutting depth is the most significant on cutting force; the next is the feed rate and the cutting speed is at least.

Molecular Dynamics Study on the Impact of the Cutting Depth to the Titanium Nanometric Cutting

2014 ◽  
Vol 536-537 ◽  
pp. 1431-1434 ◽  
Author(s):  
Ying Zhu ◽  
Yin Cheng Zhang ◽  
Shun He Qi ◽  
Zhi Xiang
Keyword(s):  
Molecular Dynamics ◽  
Potential Energy ◽  
Cutting Force ◽  
Simulation Study ◽  
Cutting Process ◽  
Work Piece ◽  
Cutting Depth ◽  
Nanometric Cutting ◽  
The Impact

Based on the molecular dynamics (MD) theory, in this article, we made a simulation study on titanium nanometric cutting process at different cutting depths, and analyzed the changes of the cutting depth to the effects on the work piece morphology, system potential energy, cutting force and work piece temperature in this titanium nanometric cutting process. The results show that with the increase of the cutting depth, system potential energy, cutting force and work piece temperature will increase correspondingly while the surface quality of machined work piece will decrease.

Analysis of the effect of tool posture on stability considering the nonlinear dynamic cutting force coefficient

2021 ◽  
pp. 1-19
Author(s):  
Zepeng Li ◽  
Rong Yan ◽  
Xiaowei Tang ◽  
Fang Yu Peng ◽  
Shihao Xin ◽  
...  
Keyword(s):  
Cutting Force ◽  
Nonlinear Dynamic ◽  
Chip Thickness ◽  
Cutting Depth ◽  
Force Coefficient ◽  
Critical Cutting Depth ◽  
Dynamic Cutting Force ◽  
Cutting Force Coefficient ◽  
Tool Posture ◽  
Instantaneous Uncut Chip Thickness

Abstract In aviation and navigation, complicated parts are milled with high-speed low-feed-per-tooth milling to decrease tool vibration for high quality. Because the nonlinearity of the cutting force coefficient (CFC) is more evident with the relatively smaller instantaneous uncut chip thickness, the stable critical cutting depth and its distribution against different tool postures are affected. Considering the nonlinearity, a nonlinear dynamic CFC model that reveals the effect of the dynamic instantaneous uncut chip thickness on the dynamic cutting force is derived based on the Taylor expansion. A five-axis bull-nose end milling dynamics model is established with the nonlinear dynamic CFC model. The stable critical cutting depth distribution with respect to tool posture is analyzed. The stability results predicted with the dynamic CFC model are compared with those from the static CFC model and the constant CFC model. The effects of tool posture and feed per tooth on stable critical cutting depth were also analyzed, and the proposed model was validated by cutting experiments. The maximal stable critical cutting depths that can be achieved under different tool postures by feed per tooth adjustment were calculated, and corresponding distribution diagrams are proposed for milling parameter optimization.

scholarly journals Experiments in the Machining of Ice at Negative Rake Angles

1984 ◽  
Vol 30 (104) ◽  
pp. 77-81 ◽  
Author(s):  
D.K. Lieu ◽  
C.D. Mote
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Cutting Depth ◽  
Orthogonal Machining ◽  
Cutting Force Components ◽  
Force Components

AbstractThe cutting force components and the cutting moment on the cutting tool were measured during the orthogonal machining of ice with cutting tools inclined at negative rake angles. The variables included the cutting depth (< 1 mm), the cutting speed (0.01 ms−1to 1 ms−1), and the rake angles (–15° to –60°). Results of the experiments showed that the cutting force components were approximately independent of cutting speed. The resultant cutting force on the tool was in a direction approximately normal to the cutting face of the tool. The magnitude of the resultant force increased with the negative rake angle. Photographs of ice-chip formation revealed continuous and segmented chips at different cutting depths.

Sign in / Sign up

Export Citation Format

Share Document