scholarly journals Features of the wear of the working bodies of the Viking tillage unit

Author(s):  
I.V. Liskin ◽  
◽  
S.A. Sidorov ◽  
D.A. Mironov ◽  
A.V. Mironov ◽  
...  

It is shown that the most uniform wear of the bit blade occurs when soil particles move perpendicular to the blade edge. It has been determined that the width of the edge affects the traction resistance of the body, the penetration ability, and the strength of the blade. It has been found that in case of loamy soils, the optimal width of the blade part is in the range between 70 and 80 mm at an acute angle of 50 degrees between the bit blade and the side edge.

Author(s):  
Fesenko, H.

Purpose. Increasing the uniformity of distribution of mineral fertilizers and other bulk materials due to the stability of their feed from the body to the spreading working bodies using the top feeder. Methods. The following methods are used to achieve this aim: the method of comparing the differences between individual groups of fertilizers, the method of analyzing the properties of a new technical system, the method of functional inventiveness, and the methods of theoretical and analytical mechanics. Results. The traction body of the conveyor of the upper feed of the body fat body machine for mineral fertilizers and other bulk materials was substantiated and the relationship between the height of its scrapers and the distance between them was established, as well as the nature of the mineral fertilizer pressure on the curvilinear wall of the body. In addition, the design of the advanced body fertilizer spreader is justified, which ensures a stable flow of fertilizers from the body due to the improvement of the top feeder. Conclusions. Because of the conducted researches, the advantages of machines equipped with top feeder are found. They create the conditions for the forced feeding mineral fertilizers and other loose materials from the container to the distribution bodies, which is a prerequisite for their evenness on the surface. With this, the imperfection of known machines with the top feeder constrains their introduction into agricultural production. On this account, a more thoroughly constructed solution of the body feeder of the top feed is substantiated, in which the conveyor provides a stable supply of fertilizers from the body with reduced energy consumption during operation. Keywords: analysis, feed, upper device, conveyor, stability, fertilizers, flow ability, body.


2020 ◽  
Vol 67 (1) ◽  
pp. 111-115
Author(s):  
Sergey A. Voynash ◽  
Viktoriya A. Sokolova ◽  
Viktor I. Kretinin ◽  
Viktor A. Markov ◽  
Elena A. Alekseeva Alekseeva ◽  
...  

One of the main factors that determine the resistance of blade working bodies against damage under dynamic loads is their resistance to plastic crumpling, brittle or fatigue failure. Hard alloys that strengthen the blades of tillage parts are more brittle materials than steel, so the blunting of their edges is caused by the formation of cracks, their gradual growth or microchipping, even from a possible single impact of a solid inclusion in the soil. In addition to the usual brittle fracture of hard alloys, fatigue failure occurs under cyclic impact conditions. (Research purpose) The research purpose is in identifying the pattern of destruction of the blade edge of soil-cutting parts of forestry machines and theoretically justifying the algorithm for assessing the strength to determine the rational thickness of the wear-resistant coating during hardening. (Materials and methods) The article presents the main regularities of the influence of material properties and geometric parameters of the blade on the radius of rounding. (Results and discussion) The process of breaking the edge of the blade of hardened working bodies of forestry machines has been studied. The claim that the blunting of the blades is mainly due to its destruction and not to wear has been proved. The article presents a method for evaluating the strength of bimetallic blades of soil-cutting parts of forestry machines. It was found that the blunting of the blade occurs as a result of edge destruction in the process of multiple impacts of solid soil inclusions along the edge of the blade. (Conclusions) The article shows that the destruction of the edge of the blade leads to blunting of soil-cutting parts, which affects their performance. It was found that the sharpness of a self-sharpening hardened blade is determined by the thickness of the reinforcing layer and its ability to resist destruction under impact.


1900 ◽  
Vol 7 (12) ◽  
pp. 560-561
Author(s):  
G. C. Crick

The name Nautilus clitellarius was given by J. de C. Sowerby to a Nautiloid from the Coal-measures, Coalbrookdale, Shropshire, and the description was accompanied by three figures, each representing a different specimen. In 1884 the species was included by Professor Hyatt in his new genus Ephippioceras. In 1891 Dr. A. H. Foord found a new species, Ephippioceras costatum, which was said to be “distinguished from E. clitellarium (to which it is, however, very closely related) by the character of the septa and by the surface ornaments. The septa in E. costatum do not form such an acute lobe upon the periphery as do those of E. clitellarium, and they are also a little wider apart in the former species than they are in the latter. Moreover, E. costatum is provided with prominent transverse costæ, which are strongest upon the sides of the shell where they swell out into heavy folds. These costæ are directed obliquely backwards, and cross the septa at an acute angle, passing across the periphery and forming a shallow sinus in the middle. None of the specimens in the British Museum have the test preserved, so that the ribbing has only been observed upon casts. The costæ are equally well developed upon the body-chamber and upon the septate part of the shell in the adult, but they were either very feeble or altogether absent in the young.” A re-examination of the specimens in the Museum collection shows that the separation of the two forms is quite justifiable.


1976 ◽  
Vol 39 (2) ◽  
pp. 401-419 ◽  
Author(s):  
B. E. Stein ◽  
B. Magalhaes-Castro ◽  
L. Kruger

A stratified organization of visual, somatic and acoustic representations was observed in the cat SC. Cells of the superficial laminae were exclusively visual. Visual, somatic, and acoustic cells were observed in the intermediate laminae while the deeper laminae were predominantly nonvisual. A detailed examination of the tactile representation revealed a somatotopic plan which was in register with the overlying visuotopy. The magnified representation of central visual fields overlapped the magnified tactile representation of the face and, as visual RFS moved temporally, the underlying tactile RFS were displaced caudal and distal. This topographical overlap can be recognized if the visual field is depicted as a flexible sheet which is stretched over the body with the area centralis superimposed on the nose and the limbs radiating out at an acute angle. The overlapping topographies and similarities in stimulus specificity of somatic and visual cells, as well as the similar behavioral deficits previously described following SC lesions, suggests a functional parallel between modalities in the SC. The possibility that visual, somatic, and acoustic cells converge on a common delivery or distribution system, which is located in the intermediate-deeper SC strata and organizes orienting and following responses on the basis of multimodality cues, is discussed.


1960 ◽  
Vol 38 (5) ◽  
pp. 913-916
Author(s):  
Liang-Yu Wu
Keyword(s):  
The Body ◽  

Criconema celetum, n, sp., is described from African violets collected at St. Laurent, Quebec. The body has 40–43 annules, each having a row of spines except at the caudal end; those near the middle of the body each having a row of about 70 spines. The head consists of two annules with spines, the first 22–28 μ in diameter and the second 19–23.5 μ. The annules at the caudal end have spatulate projections each with several spines. The spear is 84.3–95 μ (with one exception, 100 μ) long. The body is coated with soil particles under and around the spines.


2021 ◽  
Vol 3 (144) ◽  
pp. 122-129
Author(s):  
Aleksandr M. Mikhal’chenkov ◽  
◽  
Natal’ya V. Sinyaya ◽  
Aleksandr M. Sluchevskiy ◽  
Nelli Yu. Kozhukhova

The intensification of crop production has led to the creation of equipment for high-speed tillage. The high speed of plowing causes an increased intensity of wear of the working bodies of plows. The limit capacity of the vertical knife when processing loamy soils is about 30 hectares, after which the body must be subjected to repair (maintenance) operations. (Research purpose) The research purpose is in studying the wear of the right knives of the PSKU plow (geometry and location on the working surface), assessing the technical condition and develop measures to improve their durability. (Materials and methods) The right knife (plowshare) performs the function of a pruning element, its design corresponds to the design of the plowshare in the classic version, but with reduced dimensions. We carried out wear control in width and thickness on 14 parts. (Results and discussion) The knives after working 30 hectares are suitable for further use in width. The width of the solid layer deposited on the back side is about 7-8 millimeters, so additional surfacing of the abrasive-resistant alloy is necessary. The wear on the thickness of the knife cannot be the reason for its decommissioning, since the strength and rigidity are preserved, and the agrotechnical requirements for soil cultivation are not violated. (Conclusions) The residual width and thickness of the studied knives when plowing loam retain the normalized limits, which indicates the possibility of their further operation, but it is necessary to weld the cutting-blade part from the back with an abrasive- resistant alloy. The xiphoid wear is fused with an electrode that provides a roller hardness of about 50 HRC. A low level of wear rate of the part is achieved due to the hardness of the blade area 60 HRC.


1998 ◽  
Vol 353 (1372) ◽  
pp. 1101-1114 ◽  
Author(s):  
R. Leon Hughes ◽  
Leslie S. Hall

Information on the pre–hatching development of the platypus, Ornithorhynchus anatinus , is reliant on a small number of specimens, whose precise age is unknown. Material collected for J. P. Hill and now housed in the Hubrecht International Embryological Laboratory, Utrecht, contributes a major source of specimens. This paper presents new observations on developmental stages from the Hill collection, which allow for a more complete description of pre–hatching development. A feature of the pre–embryonic development of the platypus is the incomplete meroblastic cleavage. A column of fine yolk spheres extends from beneath the embryonic blastodisc towards the centre of a yolky vitellus, as seen in birds. The major expansion of extra–embryonic membranes occurs after the formation of the primitive streak. The primitive streak develops within an embryonal area as part of the superficial wall of the yolk–sac, a feature also shared with marsupials, birds and reptiles. The full–term, subspheroidal, intrauterine egg of the platypus has a major axis of about 17 mm and contains a flat, 19 to 20 somite, neurula–stage embryo which has prominent trigeminal ganglion primordia. The embryo at this stage is in a period of rapid modelling of the major early organ primordia of the nervous system, cardiovascular system, excretory system, and somite–derived components of the body wall. Soon after laying, five primary brain vesicles are present, the trigeminal ganglia CN5 as well as CN7, CN8, CN9, CN10, CN11 and CN12 are well developed. The alimentary system has an expanded stomach, pancreatic primordia and a gall bladder. Mesonephric tubules are associated with patent mesonephric ducts, which empty laterally into the cloaca. Extra–embryonic membranes at this stage show an extensive chorioamniotic connection that extends through the greater part of the caudal half of fused amniotic folds. The vascularized yolk–sac consists of a superficial yolk–sac omphalopleura and a deep yolk–sac splanchnopleure. The non–vascularized yolk–sac comprises one–quarter of the aboembryonal pole. Some distinctive monotreme features have developed by the mid–incubation period. The head is bent at an acute angle to the main body axis. The blunt upturned snout marks the site of the future oscaruncle and on the maxilla there is a median primordial papilla representing the egg tooth. The eye is open with a partly pigmented retinal ring. The forelimbs have partly separated digits, and the hindfeet are paddles. Just before hatching the upturned snout contains an oscaruncle and a sharp recurved median egg tooth. Forelimbs are pronated with separate digits possessing claw primordia. Portions of the highly vascularized extra–embryonic membranes are attached to the umbilical region and the flattened vesicular allantois has a distal region fused with the chorion. Prominent features of the hatchling are the presence of a bluntly conical oscaruncle and a translucent, horn–like egg tooth. These structures are thought to enable the hatchling to extricate itself from the egg shell. At hatching, the forelimbs exhibit clawed digits and are capable of digitopalmar prehension. Hindlimbs are still paddles with digital rays. A prominent yolk–sac navel is present. The newly hatched platypus has an external form similar to that of a new–born marsupial. The early development of the platypus has many major differences to the developmental sequence for humans, which has been categorized by the use of Carnegie Stages. The rate of somitogenesis of the platypus is faster in relation to the central nervous system morphogenesis than seen in humans, and the size of the early platypus embryonal area is massive in relation to that of humans. The unique morphology and function of extra–embryonic membranes in the platypus defies comparative staging with human development. Structures adapted for altricial survival of the platypus hatchling require the acquisition of functional competence at an earlier stage of organogenesis than seen in eutherians, although they are reminiscent of those found in new–born marsupials.


2019 ◽  
Author(s):  
T. Yaginuma ◽  
K. Kushiro ◽  
M. Takai

AbstractIn recent years, many types of micro-engineered platform have been fabricated to investigate the influences of surrounding microenvironments on cell migration. Previous researches demonstrate that microgroove-based topographies can influence cell motilities of normal and cancerous cells differently. In this paper, the microgroove wall angle is altered from obtuse to acute angles and the resulting differences in the responses of normal and cancer cells are investigated to explore the geometrical characteristics that can efficiently distinguish normal and cancer cells. Interestingly, trends in cell motilities of normal and cancer cells as the wall angles are varied between 60-120° were different, and in particular, invasive cancer cells exhibit a unique, oscillatory migratory behavior. Results from the immunostaining of cell mechanotransduction components suggest that this difference stems from directional extension and adhesion behaviors of each cell type. In addition, the specific behaviors of invasive cancer cells are found to be dependent on the myosin II activity, and modulating the activity can revert cancerous behaviors to normal ones. These novel findings on the interactions of acute angle walls and cancer cell migration provide a new perspective on cancer metastasis and additional strategies via microstructure geometries for the manipulations of cell behaviors in microscale biodevices.Statement of SignificanceCancer metastasis is the leading cause of cancer patient deaths, and yet how the microstructures within the body affect this cell migration phenomenon is not well understood. In this paper, microdevices containing microgroove structures of varying geometries, in particular obtuse and acute angles, were utilized to monitor cell motilities of various cancer cells to understand the influences of the geometrical features of microstructures on cancer metastasis. Surprisingly, it was found that the acute angle geometries lowered the persistence of migration for cancer cells, which was a totally different response from non-cancerous cells. These new findings would enable the next-generation biodevices to analyze, separate and capture cancer cells, as well as shed light onto the underlying mechanisms of cancer metastasis.


2020 ◽  
Vol 180 ◽  
pp. 03019
Author(s):  
Gabriel Gheorghe ◽  
Daniel Lates ◽  
Catalin Persu ◽  
Marinela Mateescu

The article will present a static analysis of the equipment in order to calculate the vector field distribution of the relative resulting displacement in the structure, the Cauchy stress tensor and tensor fields distribution of the specific deformation in the same structure. This is done in order to improve the structure and highlight the most vulnerable points within an equipment depending on the way of working. After performing the static analysis, tensometric marks were mounted in the most vulnerable points to calculate the displacement of the material and to calculate the major forces that appeared in the structure during the field experiments. At the same time, the idea of the equipment prototype was to improve the equipment with vibrating elements on the working bodies of the body type in order to increase the degree of crushing and to reduce the advancing forces, respectively to reduce the fuel consumption. Therefore, a modal analysis was performed to calculate the vibrations that appeared in the structure in order not to resonate with the frequency of the motor mounted on the working member.


2018 ◽  
Vol 13 (4) ◽  
pp. 109-113
Author(s):  
Рим Камалетдинов ◽  
Rim Kamaletdinov ◽  
Зиннур Рахимов ◽  
Zinnur Rakhimov ◽  
Ринат Абдрахманов ◽  
...  

The article describes the process of destruction of soil lumps on sifting separators of potato harvesters, based on the theory of low-cycle fatigue strength, based on the position that the destruction occurs as a result of the presence of initial defects and consists in the nucleation and development of cracks present in the body. A probabilistic model of reducing to “pass-through” sizes of large soil particles is considered, considering not only their destructive, but also hardening effect of cyclic loads of sifting separators, as well as the effect of areas of load application to the lump on the intensity of the destruction process and the purity of the heap. The conclusion was obtained that it is possible to increase the efficiency of the process of destruction of soil particles when using vibration effects. A design is proposed and the optimal parameters of a vibration separator with a reflector are determined.


Sign in / Sign up

Export Citation Format

Share Document