scholarly journals PENGARUH PENAMBAHAN FLY ASH (ABU TERBANG) DAN ABU SEKAM PADI TERHADAP KUAT TEKAN BATA MERAH PEJAL KONVENSIONAL

2019 ◽  
Vol 10 (1) ◽  
pp. 39-44
Author(s):  
Bimo Prakoso ◽  
Elhusna Elhusna ◽  
Ade Sri Wahyuni
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Moisture Content ◽  
Rice Husk ◽  
Test Specimen ◽  
Rice Husk Ash ◽  
Water Quantity ◽  
Clay Brick ◽  
Building Element

Red brick is a building element used in the construction of buildings and made of clay plus water with or without material mixture of other materials. Fly ash and rice husk ash contain silica. Silica is a material that has the nature of pozzolan which can increase the compressive strength of the brick when mixed with the soil. This study aims to determine the effect of the addition of fly ash and rice husk ash (ASP) to the value of compressive strength of clay brick. The process of making the test specimen follows the procedure in the brick factory.Variations of specimens made were normal bricks and bricks with the addition of fly ashand rice husk ash (ASP) used were 5%, 10%, 15%, 20%, 25% and 30% to the weight of clay.The number of test specimens of each percentage of fly ash and rice husk ash (ASP) as much as 12 specimens. The method of testing of red brick strength is referred to SNI 15-20942000. The result of the research shows that the compressive strength of the clay brick has decreased from normal clay brick by 38,97 kg/cm². The biggest decrease in compressive strength value obtaines at clay brick with 30% ashes (48,04%) and the smallest decreased obtaines at clay brick compressive strength in clay brick with 5% ash (5,98%). The decrease of the compressive strength is influenced by the amount of ash addition, water quantity and moisture content.

Physical Properties of Cement Mortar Containing Waste Ash

2015 ◽  
Vol 804 ◽  
pp. 129-132
Author(s):  
Sumrerng Rukzon ◽  
Prinya Chindaprasirt
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Cement Mortar ◽  
Ash Content ◽  
Water Requirement ◽  
Test Results ◽  
Pozzolanic Material ◽  
Materials Used

This research studies the potential for using waste ash from industrial and agricultural by-products as a pozzolanic material. Classified fly ash (FA) and ground rice husk ash (RA) were the materials used. Water requirement, compressive strength and porosity of cement mortar were investigated. Test results indicated that FA and RA (waste ash) have a high potential to be used as a good pozzolanic material. The water requirement of mortar mix decreases with the increases in fly ash content. For ground rice husk ash (RA), the water requirement of mortar mix increases with the increases in rice husk ash content. In addition, the reduction in porosity was associated with the increase in compressive strength.

scholarly journals Development of a Zero-Cement Binder Using Slag, Fly Ash, and Rice Husk Ash with Chemical Activator

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
M. R. Karim ◽  
M. F. M. Zain ◽  
M. Jamil ◽  
F. C. Lai
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Setting Time ◽  
Time Flow ◽  
Alumina Gel ◽  
Cement Binder ◽  
Increasing Demand ◽  
Chemical Activator

The increasing demand and consumption of cement have necessitated the use of slag, fly ash, rice husk ash (RHA), and so forth as a supplement of cement in concrete construction. The aim of the study is to develop a zero-cement binder (Z-Cem) using slag, fly ash, and RHA combined with chemical activator. NaOH, Ca(OH)2, and KOH were used in varying weights and molar concentrations. Z-Cem was tested for its consistency, setting time, flow, compressive strength, XRD, SEM, and FTIR. The consistency and setting time of the Z-Cem paste increase with increasing RHA content. The Z-Cem mortar requires more superplasticizer to maintain a constant flow of110±5% compared with OPC. The compressive strength of the Z-Cem mortar is significantly influenced by the amounts, types, and molar concentration of the activators. The Z-Cem mortar achieves a compressive strength of 42–44 MPa at 28 days with 5% NaOH or at 2.5 molar concentrations. The FTIR results reveal that molecules in the Z-Cem mortar have a silica-hydrate (Si-H) bond with sodium or other inorganic metals (i.e., sodium/calcium-silica-hydrate-alumina gel). Therefore, Z-Cem could be developed using the aforementioned materials with the chemical activator.

Use of Water Glass from Rice Husk and Bagasse Ashes in the Preparation of Fly Ash Based Geopolymer

2019 ◽  
Vol 798 ◽  
pp. 364-369 ◽  
Author(s):  
Khemmakorn Gomonsirisuk ◽  
Parjaree Thavorniti
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Ball Mill ◽  
Water Glass ◽  
Rice Husk Ash ◽  
Raw Materials ◽  
Agricultural Waste ◽  
Preparation Process

The aim of this work is to study the feasibility of preparation of fly ash based geopolymer using sodium water glass from agricultural waste as alternative activators. Rice husk ash and bagasse ash were used as raw materials for producing sodium water glass solution. The sodium water glass were produced by mixing rice husk ash and bagasse ash with NaOH in ball mill and boiling. The prepared sodium water glass were analyzed and used in geopolymer preparation process. The geopolymer paste were prepared by adding the obtained water glass and NaOH with fly ash. After cured at ambient temperature for 7 days, mechanical properties were investigated. Bonding and phases of the geopolymer were also characterized. The geopolymer from rice husk ash presented highest compressive strength about 23 MPa while the greatest for bagasse ash was about 16 MPa.

Development of Geopolymer Mortar from Metakaolin Blended with Agricultural and Industrial Wastes

2018 ◽  
Vol 766 ◽  
pp. 305-310 ◽  
Author(s):  
Chayanee Tippayasam ◽  
Sarochapat Sutikulsombat ◽  
Jamjuree Paramee ◽  
Cristina Leonelli ◽  
Duangrudee Chaysuwan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Chemical Properties ◽  
Cement Industry ◽  
Industrial Wastes ◽  
Engineering Properties ◽  
Alkali Solutions ◽  
Physical And Chemical

Geopolymer is a greener alternative cement produced from the reaction of pozzolans and strong alkali solutions. Generally, the cement industry is one of largest producers of CO2that caused global warming. For geopolymer mortar usage, Portland cement is not utilized at all. In this research, geopolymer mortars were prepared by mixing metakaolin, various wastes (fly ash, bagasse ash and rice husk ash) varied as 80:20, 50:50 and 20:80, 15M NaOH, Na2SiO3and sand. The influence of various parameters such as metakaolin to ashes ratios and pozzolans to alkali ratios on engineering properties of metakaolin blended wastes geopolymer mortar were studied. Compressive strength tests were carried out on 25 x 25 x 25 mm3cube geopolymer mortar specimens at 7, 14, 21, 28 and 91 air curing days. Physical and chemical properties were also investigated at the same times. The test results revealed that the highest compressive strength was 20% metakaolin - 80% fly ash geopolymer mortar. When the curing times increases, the compressive strength of geopolymer mortar also increases. The mixing of metakaolin and bagasse ash/rice husk ash presented lower compressive strength but higher water absorption and porosity. For FTIR results, Si-O, Al-O and Si-O-Na+were found. Moreover, the geopolymer mortar could easily plastered on the wall.

Effect of Soil Type in Compressed Earth Brick (CEB) with Uncontrolled Burnt Rice Husk Ash (RHA)

2012 ◽  
Vol 626 ◽  
pp. 971-975
Author(s):  
Fetra Venny Riza ◽  
Ismail Abdul Rahman ◽  
Ahmad Zaidi Ahmad Mujahid ◽  
Lee Yee Loo
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Soil Type ◽  
Building Material ◽  
Rice Husk Ash ◽  
Soil Types ◽  
Clay Brick ◽  
Commercial Value ◽  
Better Than

Compressed Earth Brick (CEB) as building material has many advantages compared to conventional fired clay brick in the view of sustainability, moreover if incorporated uncontrolled burnt RHA waste that usually dumped off since it has no commercial value. This paper tried to assess the effect of soil types of clay and laterite in CEB properties which abundantly available in Malaysia. The result showed that the compressive strength of CEB with 20% RHA using clay at 5.5 MPa is better than that of laterite 4.9 MPa, and both exceed that of commercial unfired clay brick from UK.

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

scholarly journals Study of Fly Ash, Rice Husk Ash and Marble Powder as Partial Replacement to Cement in Concrete

2020 ◽  
Vol 13 (3) ◽  
pp. 315-321
Author(s):  
Dhiraj Ahiwale ◽  
Rushikesh Khartode
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Scale Production ◽  
Environmental Threat ◽  
Marble Powder

Now days, the waste rice husk from rice mill, marble powder from tile industry and fly ash from steam power plant are necessary to utilize as partial replacement of cement for concrete production. Large scale production of cement required consumption of raw materials and energy as well as emissions to air which posse’s environmental threat in various areas of country. Apart from the environmental threat, there still exists the problem of shortage in many areas. Therefore, substitute material for concrete needs to be considered. The paper aims to analyze the compressive strength of concrete cubes and flexural strength of concrete beams made from partially replaced cement, sand, and coarse aggregate. This research study adopted in laboratory on 48 total specimens of grade M25 concrete cubes of size 150x150x150mm and concrte beams of size 100x100x500mm were casted. Out of the 48 concrete specimens cast, 6 each were made out 10%, 20%, and 30 % replacement of fly ash, rice husk ash and marble powder to cement in concrete. It was found that the compressive strength and flexural strength of concrete made from the mixture of 20 % partially replaced cement, sand and coarse aggregate was similar than the concrete made from without replaced cement , sand and coarse aggregate.

Improved Acid Rain Resistance of High Calcium Fly Ash-sodium Hydroxide Geopolymer Mortar Cured at Ambient Temperature by Incorporating Rice Husk Ash

2021 ◽  
Vol 47 (2) ◽  
pp. 324-331
Author(s):  
Prinya Chindaprasirt ◽  
Kiatsuda Somna
Keyword(s):  
Compressive Strength ◽  
Sulfuric Acid ◽  
Fly Ash ◽  
Nitric Acid ◽  
Acid Rain ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Acid Resistance ◽  
Portland Cement Concrete ◽  
High Calcium

Geopolymer is an aluminosilicate material, synthesized from source materials rich in silica and alumina and alkali solution. This product provides similar strength to Portland cement concrete. Geopolymer exhibits a wide variety of properties and characteristics, including high compressive strength, low shrinkage, acid resistance, fire resistance and low thermal conductivity. In term of acid resistance, acid rain is an important consideration due to global warming. Structures deteriorate as a result of persistence contact with acid rain with of pH less than 5. Thus, this research aims to improve acid resistance of fly ash-NaOH geopolymer mortars by incorporating rice husk ash (RHA). Artificial acid rain solution was prepared by mixing nitric acid and sulfuric acid at the ratio of 70:30 v/v. The geopolymer mortars were immersed in 5% nitric acid, 5% sulfuric acid, and 5% synthetic acid rain solutions for 36 weeks. The evaluations of its resistance to acid solution was investigated with surface corrosion, compressive strength, and microstructure. The results showed that the incorporation of RHA improved the acid rain resistance of geopolymer mortar through pore refinement and increase in strength. The mortar with fly ash to RHA ratio of 90:10 provided the highest compressive strength and good resistance to acid rain.

The Properties of Nanocarbontubes Cement Mortar Incorporating Mineral Additives

2014 ◽  
Vol 875-877 ◽  
pp. 383-387 ◽  
Author(s):  
Teuku Ferdiansyah ◽  
Hashim Abdul Razak
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Rice Husk ◽  
Electrical Resistance ◽  
Rice Husk Ash ◽  
Cement Mortar ◽  
Cement Content ◽  
Cement Ratio ◽  
Mineral Additives

The purpose of this paper is to discuss the influence of mineral additives i.e. metakaolin, silica fume, rice ash and fly ash incorporating with nanocarbontubes mortar composites. The effects on compressive strength at 28 days were also discussed and presented. Cement content of 500 kg/m3, water/cement ratio of 0.6 and aggregate/cement ratio of 2.75 were adopted for the mix propotion. 1%, 3% and 5% of nanocarbontubes in mortar were combined with 15% of mineral additives. The results show that mixtures of nanocarbontubes with 15% of metakaolin produce better strength compared to normal mortar. Meanwhile with addition of fly ash and rice husk ash the strength were decreased. The electrical resistance for all mixes at 28 days were also discussed and presented. The higher percentages of nanocarbon with addition of all mineral additives resulted in lower electrical resistance properties

Sign in / Sign up

Export Citation Format

Share Document