scholarly journals A 0.3 V, Rail-to-Rail, Ultralow-Power, Non-Tailed, Body-Driven, Sub-Threshold Amplifier

2021 ◽  
Vol 11 (6) ◽  
pp. 2528 ◽  
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Supply Voltage ◽  
Cmos Technology ◽  
Gain Bandwidth ◽  
Common Mode ◽  
Input Stage ◽  
Fully Differential ◽  
Common Mode Voltage ◽  
Rail To Rail ◽  
The Common ◽  
Ultralow Power

A novel, inverter-based, fully differential, body-driven, rail-to-rail, input stage topology is proposed in this paper. The input stage exploits a replica bias control loop to set the common mode current and a common mode feed-forward strategy to set its output common mode voltage. This novel cell is used to build an ultralow voltage (ULV), ultralow-power (ULP), two-stage, unbuffered operational amplifier. A dual path compensation strategy is exploited to improve the frequency response of the circuit. The amplifier has been designed in a commercial 130 nm CMOS technology from STMicroelectronics and is able to operate with a nominal supply voltage of 0.3 V and a power consumption as low as 11.4 nW, while showing about 65 dB gain, a gain bandwidth product around 3.6 kHz with a 50 pF load capacitance and a common mode rejection ratio (CMRR) in excess of 60 dB. Transistor-level simulations show that the proposed circuit outperforms most of the state of the art amplifiers in terms of the main figures of merit. The results of extensive parametric and Monte Carlo simulations have demonstrated the robustness of the proposed circuit to PVT and mismatch variations.

scholarly journals A 2.5 Gbps, 10-Lane, Low-Power, LVDS Transceiver in 28 nm CMOS Technology

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 350 ◽  
Author(s):  
Xu Bai ◽  
Jianzhong Zhao ◽  
Shi Zuo ◽  
Yumei Zhou
Keyword(s):  
Low Power ◽  
High Speed ◽  
Low Voltage ◽  
Cmos Technology ◽  
Common Mode ◽  
Serial Interface ◽  
Common Mode Voltage ◽  
Rail To Rail ◽  
The Common ◽  
28 Nm

This paper presents a 2.5 Gbps 10-lane low-power low voltage differential signaling (LVDS) transceiver for a high-speed serial interface. In the transmitter, a complementary MOS H-bridge output driver with a common mode feedback (CMFB) circuit was used to achieve a stipulated common mode voltage over process, voltage and temperature (PVT) variations. The receiver was composed of a pre-stage common mode voltage shifter and a rail-to-rail comparator. The common mode voltage shifter with an error amplifier shifted the common mode voltage of the input signal to the required range, thereby the following rail-to-rail comparator obtained the maximum transconductance to recover the signal. The chip was fabricated using SMIC 28 nm CMOS technology, and had an area of 1.46 mm2. The measured results showed that the output swing of the transmitter was around 350 mV, with a root-mean-square (RMS) jitter of 3.65 [email protected] Gbps, and the power consumption of each lane was 16.51 mW under a 1.8 V power supply.

Fully Differential Class-AB OTA with Improved CMRR

2017 ◽  
Vol 26 (11) ◽  
pp. 1750169 ◽  
Author(s):  
Francesco Centurelli ◽  
Pietro Monsurrò ◽  
Gaetano Parisi ◽  
Pasquale Tommasino ◽  
Alessandro Trifiletti
Keyword(s):  
Cmos Technology ◽  
Current Mirror ◽  
Differential Mode ◽  
Common Mode ◽  
Common Mode Rejection Ratio ◽  
Class Ab ◽  
Fully Differential ◽  
Rejection Ratio ◽  
Mode Behavior ◽  
The Common

This paper presents a fully differential class-AB current mirror OTA that improves the common-mode behavior of a topology that presents very good differential-mode performance but poor common-mode rejection ratio (CMRR). The proposed solution requires a low-current auxiliary circuit driven by the input signal, to compensate the effect of the common-mode input component. Simulations in 40-nm CMOS technology show a net reduction of common-mode gain of more than 90[Formula: see text]dB without affecting the differential-mode behavior; a sample-and-hold amplifier exploiting the proposed amplifier has also been simulated.

Area-Efficient Capacitor-Splitting Switching Scheme with a Nearly Constant Common-Mode Voltage for SAR ADCs

2019 ◽  
Vol 29 (10) ◽  
pp. 2020005
Author(s):  
Hao Wang ◽  
Wenming Xie ◽  
Zhixin Chen
Keyword(s):  
Dynamic Range ◽  
Supply Voltage ◽  
Sampling Rate ◽  
Cmos Technology ◽  
Switching Scheme ◽  
Common Mode ◽  
Analog To Digital ◽  
Common Mode Voltage ◽  
Switching Method ◽  
Area Efficient

A novel area-efficient switching scheme is proposed for the successive approximation register (SAR) analog-to-digital converters (ADCs). The capacitor-splitting structure, charge-average switching technique, and [Formula: see text] (equal to [Formula: see text]/4) are combined together and optimized to realize the proposed switching scheme. [Formula: see text] is only used in the last two bit cycles, which affects the ADC accuracy little and reduces capacitor area by half. It achieves a 98% less switching energy and an 87.5% less capacitor area compared with the conventional switching method. In addition, the DAC output common-mode voltage is approximately constant. Thus, the proposed switching method is a good tradeoff among power consumption, capacitor area, DAC output common-mode voltage, and ADC accuracy. The proposed SAR ADC is simulated in 0.18[Formula: see text][Formula: see text]m CMOS technology with a supply voltage of 0.6[Formula: see text]V and at a sampling rate of 20[Formula: see text]kS/s. The signal-to-noise-distortion ratio (SNDR) and spurious free dynamic range (SFDR) are 58.2 and 73.7[Formula: see text]dB, respectively. The effective number of bits (ENOB) is 9.4. It consumes 42[Formula: see text]nW, resulting in a figure-of-merit (FoM) of 3.11 fJ/conversion-step.

Feedforward Bulk-Driven Class AB Fully-Differential Second-Generation Current Conveyor (FDCCII)

2014 ◽  
Vol 979 ◽  
pp. 62-65
Author(s):  
Thawatchai Thongleam ◽  
Varakorn Kasemsuwan
Keyword(s):  
Second Generation ◽  
Transfer Characteristic ◽  
Cmos Technology ◽  
Circuit Performance ◽  
Input Stage ◽  
Class Ab ◽  
Fully Differential ◽  
Rail To Rail ◽  
Differential Pair ◽  
Dc Current

In this paper, a feedforward bulk-driven class AB fully-differential second-generation current conveyer (FDCCII) is presented. Bulk-driven differential pair is employed for the input stage allowing the FDCCII to operate with rail-to-rail operation. Feedfoward technique is also incorporated into input stage to increase the DC gain and minimize the common mode gain. The circuit performance is verified using HSPICE in 0.18 μm CMOS technology. The simulation results show rail-to-rail input and output swings. The DC voltage transfer characteristic between ports Y and X and DC current transfer characteristic between ports X and Z shows good linearity. The bandwidths show 25.7 MHz (VX/VY), 30 MHz (IZ/IX), respectively. The power dissipation is 267.5 μW.

LOW VOLTAGE LOW POWER FULLY DIFFERENTIAL BUFFER

2009 ◽  
Vol 18 (03) ◽  
pp. 497-502 ◽  
Author(s):  
VINCENZO STORNELLI
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Common Mode ◽  
Figures Of Merit ◽  
Fully Differential ◽  
General Performance ◽  
Rail To Rail ◽  
The Common

In this paper a useful CMOS fully-differential buffer topology is presented. The proposed solution, performing the common mode feedback operation, shows a rail-to-rail characteristic, so it is particularly suitable for low-voltage (± 0.75 V) low-power (< 400 μW) applications. The simulated results have shown excellent general performance, evaluated in terms of suitable figures of merit.

scholarly journals Design of current sources for load common mode optimization

2018 ◽  
Vol 9 (1) ◽  
pp. 59-71
Author(s):  
Vinicius G Sirtoli ◽  
Kaue F Morcelles ◽  
Volney C Vincence
Keyword(s):  
Voltage Drop ◽  
Current Source ◽  
Output Impedance ◽  
Output Current ◽  
Common Mode ◽  
Measurement Systems ◽  
Fully Differential ◽  
Common Mode Voltage ◽  
The Common ◽  
Bioimpedance Measurement

Abstract Bioimpedance measurement systems often use the Howland current sources to excite the biological material under study. Usually, difference or instrumentation amplifiers are used to measure the resulting voltage drop on this material. In these circuits, common mode voltage appears as artifacts in the measurement. Most researches on current sources are focused on improving the output impedance, letting other characteristics aside. In this paper, it is made a brief review on the load common mode voltage and output swing of various topologies of Howland current sources. Three circuits are proposed to reduce load common mode voltage and enhance load capability by using a fully differential amplifier as active component. These circuits are equated, simulated and implemented. The three proposed circuits were able to deliver an output current with cut-off frequency (-3dB) higher than 1 MHz for loads as big as 4.7 kΩ. The worst measured load common mode voltage was smaller than 24 mV for one of the circuits and smaller than 8 mV for the other two. Consequently, it could be obtained increases in the Common Mode Rejection Ratio (CMRR) up to 60 dB when compared to the Enhanced Howland Current Source (EHCS).

Design of a Gain-Boosted Cascode Amplifier with High Unity-Bandwidth

2014 ◽  
Vol 614 ◽  
pp. 237-240
Author(s):  
Lin Feng Wang ◽  
Qiao Meng ◽  
Hao Zhi
Keyword(s):  
Direct Current ◽  
Cmos Technology ◽  
Gain Bandwidth ◽  
Fully Differential ◽  
Common Mode Voltage ◽  
Dc Gain ◽  
Unity Gain ◽  
Folded Cascode ◽  
The Stability ◽  
Cascode Amplifier

This paper presents a high unity gain bandwidth fully differential folded-cascode operational amplifier using gain-boosted technique. The amplifier is designed in TSMC 0.18μm 1P6M CMOS technology. The unity-gain bandwidth (GBW) and poles of the gain-boosting amplifiers were carefully designed to improve the stability. The implemented design provides a direct current (DC) gain of around 93 dB with a unity gain frequency of 1.8GHz. It exhibits a DC gain larger than 88dB when the output common-mode voltage between 0.6 V and 1.2V. the overall layout size is 96μm×120μm.

scholarly journals A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 466
Author(s):  
Pawel Szczepankowski ◽  
Natalia Strzelecka ◽  
Enrique Romero-Cadaval
Keyword(s):  
Pulse Width Modulation ◽  
Harmonic Distortion ◽  
Simulation Software ◽  
Common Mode ◽  
New Approach ◽  
Matrix Converters ◽  
Load Voltage ◽  
Common Mode Voltage ◽  
The Common ◽  
Open End Winding

This article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load’s terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion (THD) of the generated load voltage. The third variant of modulation concerns maximizing the voltage transfer ratio, minimizing the number of switching, and the common-mode voltage cancellation. The discussed modulations are based on the concept of sinusoidal voltage quadrature signals, which can be an effective alternative to the classic space-vector approach. In the proposed approach, the geometrical arrangement of basic vectors needed to synthesize output voltages is built from the less number of vectors, which is equal to the number of the matrix converter’s terminals. The PWM duty cycle computation is performed using only a second-order determinant of the voltages coordinate matrix without using trigonometric functions. A new approach to the PWM duty cycles computing and the load voltage synthesis by 5 × 5 and 12 × 12 topologies has been verified using the PSIM simulation software.

Sign in / Sign up

Export Citation Format

Share Document