scholarly journals Effects of Zirconium and Yttrium Oxide on Mechanical and Oxidation Properties of Mo–3Si–1B–1Zr–1Y2O3 (wt.%) Alloy

Coatings ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 833
Author(s):  
Zhenping Guo ◽  
Lei Wang ◽  
Cheng Wang ◽  
Qiuliang Li
Keyword(s):  
Fracture Toughness ◽  
Oxidation Resistance ◽  
Yttrium Oxide ◽  
Particle Dispersion ◽  
Second Phase ◽  
Fracture Toughness Test ◽  
Dispersion Strengthening ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Second Phase Particles

Mo–3Si–1B alloys with zirconium (1 wt.%) and yttrium oxide (1 wt.%) additives were fabricated by vibrating sintering techniques. The doped Mo–3Si–1B alloys consisted mainly of α-Mo, Mo3Si, and Mo5SiB2 (T2) phases. It was found that the grains were reduced, and the intermetallics particles were dispersed more homogeneously after the addition of Zr and Y2O3. The optimization in microstructure induced corresponding improvements in both fracture toughness and oxidation resistance. The predominant strengthening mechanisms were fine-grain strengthening and particle dispersion strengthening. In addition, fracture toughness test showed that the additions could improve the toughness of Mo–3Si–1B alloys, for which the toughening mechanism involved a crack trapping by α-Mo phases and extensive small second phase particles in the alloys. What should be paid attention to is the satisfactory oxidation resistance, both at medium-low temperature (800 °C) and high temperature (1200 °C) with doped additives.

scholarly journals Microstructures and Mechanical Properties of Hot-Pressed -Matrix Composites Reinforced with SiC and Particles

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Hongming Zhou ◽  
Jian Li ◽  
Danqing Yi
Keyword(s):  
Fracture Toughness ◽  
Grain Size ◽  
Bending Strength ◽  
Testing Machine ◽  
Materials Testing ◽  
Matrix Composites ◽  
Dispersion Strengthening ◽  
Hardness Tester ◽  
Fine Grain ◽  
Fine Grain Strengthening

-matrix composites reinforced with and SiC particles were fabricated by means of wet-mixing and heat-pressing process. Scanning electron microscope (SEM), X-ray diffractometry (XRD), polarizing microscopy, Vickers hardness tester, with a universal materials testing machine were used to investigate the morphology, grain size, hardness, fracture toughness, and bending strength of the synthesized composites. Notable effects on the bending strength and fracture toughness of caused by the addition of SiC and particles were found. The composite with 20 vol.% SiC and 20 vol.% Si3N4 particles has the highest strength and toughness, which is about 100% and 340%, respectively, higher than that of pure . The grain size of decreases gradually with the volume content of SiC and particles increasing from 0% to 40%, and -20 vol% SiC-20 vol% Si3N4 composite exhibits the minimum grain size of . The relationship between the grain size of and bending strength is not entirely fit with Hall-Petch equation. The strengthening mechanisms of the composite include fine-grain strengthening and dispersion strengthening. The toughening mechanisms of the composite include fine grain, microcracking, crack deflection, crack microbridging, and crack branching.

Microstructure and Mechanical Properties of Molybdenum Alloys Doped with ZrB2 Particles

2010 ◽  
Vol 160-162 ◽  
pp. 1828-1833 ◽  
Author(s):  
Guo Jun Zhang ◽  
Jun Zhuo ◽  
Shu Ai Ren
Keyword(s):  
Mechanical Properties ◽  
Mass Fraction ◽  
Zirconium Diboride ◽  
Particle Dispersion ◽  
Dispersion Strengthening ◽  
Pure Molybdenum ◽  
Grain Sizes ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Molybdenum Alloys

The molybdenum alloys doped with various mass fraction zirconium diboride (ZrB2) particles were successfully prepared by using the powder metallurgy technology. The microstructure, hardness and the tensile properties of the pure molybdenum and molybdenum alloys doped with ZrB2 particles were determined at room temperature. Results showed that the addition of zirconium diboride refined the molybdenum grains obviously, meanwhile, molybdenum grain sizes decrease with the increasing of zirconium diboride mass fraction. Measurements on mechanical properties showed that molybdenum alloys doped with ZrB2 particles had higher hardness and strength than pure molybdenum. The analysis and discussion results show that the strengthening mechanisms of ZrB2-doped molybdenum alloys may be attributed to the fine-grain strengthening, particle dispersion strengthening, interfacial-bond strengthening and oxygen reduction strengthening.

scholarly journals Effect of Nano-Y2O3 Addition on Microstructure and Tensile Properties of High-Nb TiAl Alloy Prepared by Spark Plasma Sintering

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1048
Author(s):  
Yingchao Guo ◽  
Yongfeng Liang ◽  
Junpin Lin ◽  
Fei Yang
Keyword(s):  
Tensile Strength ◽  
Spark Plasma Sintering ◽  
Tial Alloy ◽  
Second Phase ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Y2o3 Addition ◽  
Powder Metallurgy Route

Nano-Y2O3 reinforced Ti-47.7Al-7.1Nb-(V, Cr) alloy was fabricated by a powder metallurgy route using spark plasma sintering (SPS), and the influence of nano-Y2O3 contents on the microstructure and mechanical properties were investigated systematically. The results revealed that the ultimate tensile strength and elongation of the alloy were 570 ± 28 MPa and 1.7 ± 0.6% at 800 °C, 460 ± 23 MPa and 6.1 ± 0.4% at 900 °C with no nano-Y2O3, 662 ± 24 MPa and 5.5 ± 0.5% at 800 °C, and 466 ± 25 MPa and 16.5 ± 0.8% at 900 °C with 0.05 at% nano-Y2O3 addition, respectively. Due to the fine-grain strengthening and the second-phase strengthening, both tensile strength and elongation of the high-Nb TiAl alloy were enhanced with the addition of nano-Y2O3.

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

2014 ◽  
Vol 602-603 ◽  
pp. 438-442
Author(s):  
Lei Yu ◽  
Jian Yang ◽  
Tai Qiu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Bending Strength ◽  
Coefficient Of Thermal Expansion ◽  
Raw Materials ◽  
Linear Increase ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Uniform Microstructure

Fully dense (ZrB2+ZrC)/Zr3[Al (Si)]4C6 composites with ZrB2 content varying from 0 to 15 vol.% and fixed ZrC content of 10 vol.% were successfully prepared by in situ hot-pressing in Ar atmosphere using ZrH2, Al, Si, C and B4C as raw materials. With the increase of ZrB2 content, both the bending strength and fracture toughness of the composites increase and then decrease. The synergistic action of ZrB2 and ZrC as reinforcements shows significant strengthening and toughing effect to the Zr3[Al (Si)]4C6 matrix. The composite with 10 vol.% ZrB2 shows the optimal mechanical properties: 516 MPa for bending strength and 6.52 MPa·m1/2 for fracture toughness. With the increase of ZrB2 content, the Vickers hardness of the composites shows a near-linear increase from 15.3 GPa to 16.7 GPa. The strengthening and toughening effect can be ascribed to the unique mechanical properties of ZrB2 and ZrC reinforcements, the differences in coefficient of thermal expansion and modulus between them and Zr3[Al (Si)]4C6 matrix, fine grain strengthening and uniform microstructure derived by the in situ synthesis reaction.

Dependence of fracture toughness on multiscale second phase particles in high strength Al alloys

2003 ◽  
Vol 19 (7) ◽  
pp. 887-896 ◽  
Author(s):  
G. Liu ◽  
G.-J. Zhang ◽  
X.-D. Ding ◽  
J. Sun ◽  
K.-H. Chen
Keyword(s):  
Fracture Toughness ◽  
High Strength ◽  
Al Alloys ◽  
Second Phase ◽  
Second Phase Particles

Microstructure of Friction Stir Processed Mg-Y-Zn Alloy

2007 ◽  
Vol 558-559 ◽  
pp. 777-780 ◽  
Author(s):  
Taiki Morishige ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Sachio Oki ◽  
Kenji Higashi
Keyword(s):  
Equal Channel Angular Extrusion ◽  
Second Phase ◽  
Ingot Metallurgy ◽  
Friction Stir ◽  
Fine Grained ◽  
Probe Diameter ◽  
Fine Grain ◽  
Second Phase Particles ◽  
The Matrix ◽  
Zn Alloy

Friction stir processing (FSP) is the effective method of the grain refinement for light metals. The aim of this study is to acquire the fine grained bulk Mg-Y-Zn alloy by ingot metallurgy route much lower in cost. Such bulk alloy can be formed by the superplastic forging. The microstructure of as-cast Mg-Y-Zn alloy was dendrite. The dendrite arm spacing was 72.5 [(m], and there are the lamellar structures in it. FSP was conducted on allover the plate of Mg-Y-Zn alloy for both surfaces by the rotational tool with FSW machine. The stirring passes were shifted half of the probe diameter every execution. The dendrite structures disappeared after FSP, but the lamellar structure could be observed by TEM. The matrix became recrystallized fine grain, and interdendritic second phase particles were dispersed in the grain boundaries. By using FSP, cast Mg-Y-Zn alloy could have fine-grained. This result compared to this material produced by equal channel angular extrusion (ECAE) or rapid-solidified powder metallurgy (RS P/M). As the result, as-FSPed material has the higher hardness than materials produced by the other processes at the similar grain size.

Microstructures and Mechanical Properties of B4C-TiB2 Composite Prepared by Hot Pressure Sintering

2010 ◽  
Vol 434-435 ◽  
pp. 50-53 ◽  
Author(s):  
Xin Yan Yue ◽  
Shu Mao Zhao ◽  
Liang Yu ◽  
Hong Qiang Ru
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Microstructural Analysis ◽  
Crack Deflection ◽  
Second Phase ◽  
Fine Grain ◽  
Pull Out ◽  
Microstructures And Mechanical Properties

B4C-TiB2 composite was prepared using hot pressure sintering. The microstructures and mechanical properties of the B4C-TiB2 composite were investigated. The B4C-TiB2 composite with 43 mass % TiB2 showed the optimized properties. The relative density, hardness, flexural strength and fracture toughness of that were 98.2 %, 25.9 GPa, 458 MPa and 8.7 MPa•m1/2, respectively. A number of toughening mechanisms, including fine grain, crack deflection and grain pull-out, were observed during microstructural analysis of the composite. The fracture mode of the B4C-TiB2 composite was greatly affected by the existence of the second phase of TiB2.

The Room Temperature and Elevated Temperature Fracture Toughness Response of Alloy A-286

1978 ◽  
Vol 100 (2) ◽  
pp. 195-199 ◽  
Author(s):  
W. J. Mills
Keyword(s):  
Fracture Toughness ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Second Phase ◽  
Surface Micromorphology ◽  
Second Phase Particles ◽  
The Matrix ◽  
Temperature Fracture ◽  
Increasing Temperature ◽  
Base Superalloy

The elastic-plastic fracture toughness (JIc) response of precipitation strengthened Alloy A-286 has been evaluated by the multi-specimen R-curve technique at room temperature, 700 K (800°F) and 811 K (1000°F). The fracture toughness of this iron-base superalloy was found to decrease with increasing temperature. This phenomenon was attributed to a reduction in the materials’s strength and ductility at elevated temperatures. Electron fractographic examination revealed that the overall fracture surface micromorphology, a duplex dimple structure coupled with stringer troughs, was independent of test temperature. In addition, the fracture resistance of Alloy A-286 was found to be weakened by the presence of a nonuniform distribution of second phase particles throughout the matrix.

Optimization of Particle Size and Distribution by Hydrostatic Extrusion

2007 ◽  
Vol 561-565 ◽  
pp. 869-872 ◽  
Author(s):  
Małgorzata Lewandowska ◽  
Kinga Wawer
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Aluminium Alloys ◽  
Hydrostatic Extrusion ◽  
Nanometer Scale ◽  
Second Phase ◽  
Size Refinement ◽  
Second Phase Particles ◽  
Fatigue And Fracture

Hydrostatic extrusion (HE) as a method of metals forming is known for about 100 years. Recently, it has been utilized as an efficient way of grain size refinement down to nanometer scale. In the case of engineering metals, HE processing alters not only grain size but also second phase particles such as intermetallic inclusions and precipitates. During HE processing, these particles significantly change their size, shape and spatial distribution. These changes are accompanied by improvement in properties of processed metals such as fatigue and fracture toughness. In the present work, changes of second phase particles induced by HE are described in a quantitative way for aluminium alloys. Their impact on mechanical properties is also discussed.

The Effect of Particles on Microstructure and Mechanical Behaviour of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP

2013 ◽  
Vol 765 ◽  
pp. 444-448
Author(s):  
Yin Peng Zhou ◽  
De Jiang Li ◽  
Xiao Qin Zeng ◽  
Wen Jiang Ding
Keyword(s):  
Phase Particle ◽  
Equilibrium Phase ◽  
Second Phase ◽  
Initial State ◽  
Angular Pressing ◽  
Β Phase ◽  
Fine Grain ◽  
Second Phase Particles ◽  
Particle Strengthening ◽  
Evolution Of Microstructure

An Mg-10Gd-3Y-0.4Zr alloy (GW103K) was processed by equal-channel angular pressing (ECAP) for 1-6 passes at 663 K; and the evolution of microstructure during ECAP was studied by OM and XRD. After ECAP, the grain size was reduced from 65 μm (initial state) to 4.2 μm (6 passes), the β equilibrium phase precipitated gradually and the area fraction of β phase increased from 0.8% to 13.4%. The distribution of fine grain zones and second phase particles were coincident, which was consistent with PSN. During the ECAP process, the yield strength increased up to a peak and then decreased, and the elongation increased firstly, then decreased later and increased again. The optimal mechanical properties were obtained after 3 passes, which was attributed to the combined effect grain refinement and second phase particle strengthening.

Sign in / Sign up

Export Citation Format

Share Document