scholarly journals 1.0 V-0.18 µm CMOS Tunable Low Pass Filters with 73 dB DR for On-Chip Sensing Acquisition Systems

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 563
Author(s):  
Jorge Pérez-Bailón ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Dynamic Range ◽  
Low Voltage ◽  
Cutoff Frequency ◽  
Cmos Technology ◽  
Active Area ◽  
Current Steering ◽  
Low Pass ◽  
On Chip ◽  
Low Pass Filters

This paper presents a new approach based on the use of a Current Steering (CS) technique for the design of fully integrated Gm–C Low Pass Filters (LPF) with sub-Hz to kHz tunable cut-off frequencies and an enhanced power-area-dynamic range trade-off. The proposed approach has been experimentally validated by two different first-order single-ended LPFs designed in a 0.18 µm CMOS technology powered by a 1.0 V single supply: a folded-OTA based LPF and a mirrored-OTA based LPF. The first one exhibits a constant power consumption of 180 nW at 100 nA bias current with an active area of 0.00135 mm2 and a tunable cutoff frequency that spans over 4 orders of magnitude (~100 mHz–152 Hz @ CL = 50 pF) preserving dynamic figures greater than 78 dB. The second one exhibits a power consumption of 1.75 µW at 500 nA with an active area of 0.0137 mm2 and a tunable cutoff frequency that spans over 5 orders of magnitude (~80 mHz–~1.2 kHz @ CL = 50 pF) preserving a dynamic range greater than 73 dB. Compared with previously reported filters, this proposal is a competitive solution while satisfying the low-voltage low-power on-chip constraints, becoming a preferable choice for general-purpose reconfigurable front-end sensor interfaces.

LOW VOLTAGE, LOW POWER CHEBYSHEV FILTER IN 0.18 μm CMOS TECHNOLOGY

2013 ◽  
Vol 22 (07) ◽  
pp. 1350053 ◽  
Author(s):  
S. REKHA ◽  
T. LAXMINIDHI
Keyword(s):  
Low Power ◽  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Unity Gain ◽  
Design Centering ◽  
Low Supply Voltage

This paper presents an active-RC continuous time filter in 0.18 μm standard CMOS technology intended to operate on a very low supply voltage of 0.5 V. The filter designed, has a 5th order Chebyshev low pass response with a bandwidth of 477 kHz and 1-dB passband ripple. A low-power operational transconductance amplifier (OTA) is designed which makes the filter realizable. The OTA uses bulk-driven input transistors and feed-forward compensation in order to increase the Dynamic Range and Unity Gain Bandwidth, respectively. The paper also presents an equivalent circuit of the OTA and explains how the filter can be modeled using descriptor state-space equations which will be used for design centering the filter in the presence of parasitics. The designed filter offers a dynamic range of 51.3 dB while consuming a power of 237 μW.

Design of a 10-Bit High Performance Current-Steering DAC with a Novel Nested Decoder Based on Domino Logic

2015 ◽  
Vol 24 (06) ◽  
pp. 1550086 ◽  
Author(s):  
Masoud Nazari ◽  
Leila Sharifi ◽  
Meysam Akbari ◽  
Omid Hashemipour
Keyword(s):  
Power Consumption ◽  
High Performance ◽  
Dynamic Range ◽  
Logic Gates ◽  
Cmos Technology ◽  
Total Power ◽  
Current Steering ◽  
Domino Logic ◽  
Chip Area ◽  
Total Power Consumption

In this paper, a 10-bit 8-2 segmented current-steering digital-to-analog converter (DAC) is presented which uses a novel nested binary to thermometer (BT) decoder based on domino logic gates. High accuracy and high performances are achieved with this structure. The proposed decoder has a pipelining scheme and it is designed symmetrically in three stages with repeatable logic gates. Thus, power consumption, chip area and the number of control signals are reduced. The proposed DAC is simulated in 0.18-μm CMOS technology and the spurious-free dynamic range (SFDR) is 65.3 dB over a 500 MHz output bandwidth at 1 GS/s. Total power consumption of the designed DAC is only 23.4 mW while the digital and analog supply voltages are 1.2 and 1.8 V, respectively. The active area of the proposed DAC is equal to 0.3 mm2.

An 8-Bit Ultra-Low-Power, Low-Voltage Current Steering DAC Utilizing a New Segmented Structure

2019 ◽  
Vol 28 (10) ◽  
pp. 1950172
Author(s):  
Mehdi Bandali ◽  
Alireza Hassanzadeh ◽  
Masoume Ghashghaie ◽  
Omid Hashemipour
Keyword(s):  
Low Power ◽  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
The Body ◽  
Current Steering ◽  
Ultra Low Power ◽  
Current Cell ◽  
Sample Rate

In this paper, an 8-bit ultra-low-power, low-voltage current steering digital-to-analog converter (DAC) is presented. The proposed DAC employs a new segmented structure that results in low integral nonlinearity (INL) and high spurious-free dynamic range (SFDR). Moreover, this DAC utilizes a low-voltage current cell. The low-voltage characteristic of the current cell is achieved by connecting the body of MOSFET switches to their sources. Utilizing a low supply voltage along with a low bias current in the current cells results in about 623.81-[Formula: see text]W power consumption in 140-MS/s sample rate, which is very small compared to previous reports. The post-layout simulation results in 180-nm CMOS technology and [Formula: see text]-V supply voltage with the sample rate of 140[Formula: see text]MS/s show SFDR [Formula: see text] 64.37[Formula: see text]dB in the Nyquist range. The differential nonlinearity (DNL) and INL of the presented DAC are 0.1254 LSB and 0.1491 LSB, respectively.

A Fully Differential Variable Gain Amplifier for Portable Impedance Sensing Applications

2019 ◽  
Vol 7 ◽  
Author(s):  
Jorge Pérez Bailón ◽  
Jaime Ramírez-Angulo ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Active Area ◽  
Variable Gain Amplifier ◽  
Cmos Process ◽  
Current Steering ◽  
Impedance Sensing ◽  
Variable Gain ◽  
Fully Differential ◽  
Sensing Applications ◽  
Constant Bandwidth

This paper presents a Variable Gain Amplifier (VGA) designed in a 0.18 μm CMOS process to operate in an impedance sensing interface. Based on a transconductance-transimpedance (TC-TI) approach with intermediate analog-controlled current steering, it exhibits a gain ranging from 5 dB to 38 dB with a constant bandwidth around 318 kHz, a power consumption of 15.5 μW at a 1.8 V supply and an active area of 0.021 mm2.

A 12-BIT 400-MS/s CURRENT-STEERING DAC WITH DEGLITCHING TECHNIQUE

2014 ◽  
Vol 23 (01) ◽  
pp. 1450004 ◽  
Author(s):  
XIAOBO XUE ◽  
XIAOLEI ZHU ◽  
QIFENG SHI ◽  
LENIAN HE
Keyword(s):  
Dynamic Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Current Steering ◽  
Digital To Analog Converter ◽  
Measurement Results ◽  
Voltage Swing ◽  
Current Steering Dac ◽  
Low Supply Voltage

In this paper, a 12-bit current-steering digital-to-analog converter (DAC) employing a deglitching technique is proposed. The deglitching technique is realized by lowering the voltage swing of the control signal as well as by using a method of glitch counteraction (GC). A new switch–driver structure is designed to enable the effectiveness of the GC and provide sufficient driving capability under a low supply voltage. Moreover, the control signal's rise/fall asymmetry which increases the glitch error can be suppressed by using the proposed switch–driver structure. The 12-bit DAC is implemented in 180 nm CMOS technology. The measurement results show that the spurious free dynamic range (SFDR) at low signal frequency is 78.8 dB, and it is higher than 70 dB up to 60 MHz signal frequency at 400 MS/s. The measured INL and DNL are both less than ±0.6 LSB.

scholarly journals Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters

Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2931
Author(s):  
Waldemar Jendernalik ◽  
Jacek Jakusz ◽  
Grzegorz Blakiewicz
Keyword(s):  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Low Frequency ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Biomedical Sensors ◽  
Filter Synthesis ◽  
Cascade Method

Buffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more general method for buffer-based filter synthesis is developed and presented. The method uses RLC ladder prototypes to obtain filters of arbitrary orders. In addition, a set of novel circuit solutions with ultra-low voltage and power are proposed. The introduced circuits were synthesized and simulated using 180-nm CMOS technology of X-FAB. One of the designed circuits is a fourth-order, low-pass filter that features: 100-Hz passband, 0.4-V supply voltage, power consumption of less than 5 nW, and dynamic range above 60 dB. Moreover, the total capacitance of the proposed filter (31 pF) is 25% lower compared to the structure synthesized using a conventional cascade method (40 pF).

scholarly journals A CMOS Quadrature Signal Generator for Impedance Spectroscopy Measurement Systems

2018 ◽  
Vol 6 ◽  
Author(s):  
Alejandro Márquez Marzal ◽  
Nicolás Medrano Marqués ◽  
Belén Calvo López ◽  
Pedro A. Martínez Martínez
Keyword(s):  
Impedance Spectroscopy ◽  
Power Consumption ◽  
Signal Generator ◽  
Active Area ◽  
Fully Integrated ◽  
Resolution Power ◽  
Measurement Systems ◽  
Quadrature Signal ◽  
Spectroscopy Measurement ◽  
On Chip

A CMOS fully integrated quadrature signal generator for on-chip impedance spectroscopy (IS) applications is presented. Frequency can be digitally tuned from 5 to 350 kHz with 12-bit resolution. Power consumption is 0.77 mW and active area is 0.129 mm2. Its suitability for the target application is validated with a Randles test impedance cell modelling a protein.

scholarly journals Dynamic Range Analysis of the Phase Generated Carrier Demodulation Technique

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
M. J. Plotnikov ◽  
A. V. Kulikov ◽  
V. E. Strigalev ◽  
I. K. Meshkovsky
Keyword(s):  
Theoretical Analysis ◽  
Dynamic Range ◽  
Range Analysis ◽  
Upper Limit ◽  
Low Pass ◽  
Nonlinear Character ◽  
Simulation Results ◽  
Low Pass Filters ◽  
First Time ◽  
Phase Generated Carrier

The dependence of the dynamic range of the phase generated carrier (PGC) technique on low-pass filters passbands is investigated using a simulation model. A nonlinear character of this dependence, which could lead to dynamic range limitations or measurement uncertainty, is presented for the first time. A detailed theoretical analysis is provided to verify the simulation results and these results are consistent with performed calculations. The method for the calculation of low-pass filters passbands according to the required dynamic range upper limit is proposed.

scholarly journals A Novel Highly Linear Voltage-To-Time Converter (VTC) Circuit for Time-Based Analog-To-Digital Converters (ADC) Using Body Biasing

Electronics ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 2033
Author(s):  
Ahmed Elgreatly ◽  
Ahmed Dessouki ◽  
Hassan Mostafa ◽  
Rania Abdalla ◽  
El-sayed El-Rabaie
Keyword(s):  
Power Consumption ◽  
Software Defined Radio ◽  
Dynamic Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
The Body ◽  
Analog To Digital Converters ◽  
Clock Frequency ◽  
Analog To Digital ◽  
Operation Speed

Time-based analog-to-digital converter is considered a crucial part in the design of software-defined radio receivers for its higher performance than other analog-to-digital converters in terms of operation speed, input dynamic range and power consumption. In this paper, two novel voltage-to-time converters are proposed at which the input voltage signal is connected to the body terminal of the starving transistor rather than its gate terminal. These novel converters exhibit better linearity, which is analytically proven in this paper. The maximum linearity error is reduced to 0.4%. In addition, the input dynamic range of these converters is increased to 800 mV for a supply voltage of 1.2 V by using industrial hardware-calibrated TSMC 65 nm CMOS technology. These novel designs consist of only a single inverter stage, which results in reducing the layout area and the power consumption. The overall power consumption is 18 μW for the first proposed circuit and 15 μW for the second proposed circuit. The novel converter circuits have a resolution of 5 bits and operate at a maximum clock frequency of 500 MHz.

scholarly journals A CMOS Low Pass Filter for SoC Lock-in-Based Measurement Devices

Sensors ◽  
2019 ◽  
Vol 19 (23) ◽  
pp. 5173 ◽  
Author(s):  
Jorge Pérez-Bailón ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Dynamic Range ◽  
Current Trend ◽  
Cutoff Frequency ◽  
Oxide Semiconductor ◽  
Constant Current ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Compact Size ◽  
Low Pass ◽  
Lock In

This paper presents a fully integrated Gm–C low pass filter (LPF) based on a current steering Gm reduction-tuning technique, specifically designed to operate as the output stage of a SoC lock-in amplifier. To validate this proposal, a first-order and a second-order single-ended topology were integrated into a 1.8 V to 0.18 µm CMOS (Complementary Metal-Oxide-Semiconductor) process, showing experimentally a tuneable cutoff frequency that spanned five orders of magnitude, from tens of mHz to kHz, with a constant current consumption (below 3 µA/pole), compact size (<0.0140 mm2/pole), and a dynamic range better than 70 dB. Compared to state-of-the-art solutions, the proposed approach exhibited very competitive performances while simultaneously fully satisfying the demanding requirements of on-chip portable measurement systems in terms of highly efficient area and power. This is of special relevance, taking into account the current trend towards multichannel instruments to process sensor arrays, as the total area and power consumption will be proportional to the number of channels.

Sign in / Sign up

Export Citation Format

Share Document