scholarly journals Research of PVDF Energy Harvester Cantilever Parameters for Experimental Model Realization

Electronics ◽  
2020 ◽  
Vol 9 (12) ◽  
pp. 2030
Author(s):  
Mindaugas Cepenas ◽  
Bingzhong Peng ◽  
Darius Andriukaitis ◽  
Chandana Ravikumar ◽  
Vytautas Markevicius ◽  
...  
Keyword(s):  
Experimental Data ◽  
Loss Factor ◽  
Output Voltage ◽  
Energy Harvester ◽  
Electronic Devices ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
True Model ◽  
Potential Applications ◽  
Real Value

Piezoelectric energy harvesters have been extensively researched for use with wireless sensors or low power consumption electronic devices. Most of the piezoelectric energy harvesters cannot generate enough power for potential applications. In this study, we explore the parameters, including gap and proof mass, that can affect the damping of the cantilever to optimize the design of the energy harvester. A finite analysis is conducted using COMSOL Multiphysics software. Usually, this type of simulation is performed using the loss factor. However, it is known that results from the loss factor produce models that do not fit the experimental data well. In fact, the result of output voltage using the loss factor is 50% higher than the real value, which is due to ignoring the adverse effect of a superimposing mechanical damping of different constituent materials. In order to build a true model, Rayleigh damping coefficients are measured to use in a simulation. This resulted in a closer fit of modeling and experimental data, and a 5 times better output voltage from the optimized energy harvester compared with using the smallest gap and mass.

PZT Piezoelectric Energy Harvester Enhancement Using Slotted Aluminium Beam

2014 ◽  
Vol 1051 ◽  
pp. 932-936
Author(s):  
Mun Heng Lam ◽  
Hanim Salleh
Keyword(s):  
Energy Source ◽  
Renewable Energy Source ◽  
Lead Zirconate Titanate ◽  
Output Voltage ◽  
Energy Harvester ◽  
Lead Zirconate ◽  
External Beam ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Wide Range

This paper presents work on improving piezoelectric energy harvesters. Harvesting energy from vibrations has received massive attention due to it being a renewable energy source that has a wide range of applications. Over the years of development, there is always research to further improve and optimise piezoelectric energy harvesters. For this paper, the piezoelectric specimen is made of PZT (Lead Zirconate Titanate), brass reinforced and has 31.8mm length, 12.7mm width and 0.511mm thick. An external beam is implemented to provide deflection amplification which in turn increases the output of the energy harvester. Depending on the configuration of the external beam, it can amplify output voltage from 100% to 300%.

scholarly journals An E-shape broadband piezoelectric energy harvester induced by magnets

2018 ◽  
Vol 29 (11) ◽  
pp. 2477-2491 ◽  
Author(s):  
Qingqing Lu ◽  
Fabrizio Scarpa ◽  
Liwu Liu ◽  
Jinsong Leng ◽  
Yanju Liu
Keyword(s):  
Broad Spectrum ◽  
Output Voltage ◽  
Energy Harvester ◽  
Variation Principle ◽  
Frequency Bandwidth ◽  
Restoring Force ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Half Power ◽  
Tip Mass

We describe in this work a broadband magnetic E-shape piezoelectric energy harvester with wide frequency bandwidth. We develop first a nonlinear electromechanical model of the harvester based on the Hamilton variation principle that simulates the effect of the nonlinear magnetic restoring force at different spacing distances. The model is used to identify the distances existing between two different magnets that enable the system to perform with a specific nonlinearity. The performance of the E-shape piezoelectric energy harvester is also investigated through experiments, with E-shape energy harvesters at different spacing distances tested under several base acceleration excitations. We observe that the frequency domain output voltage of the system shows a general excellent controllable performance, with a widening of the frequency bandwidth. The half-power bandwidth of the linear energy harvester for a distance of 25 mm is 0.8 Hz only, which can be expanded to 2.67 Hz for the larger distance of 11 mm between magnets. The energy harvester presented in this work shows promising performances for broad-spectrum vibration excitations compared to conventional cantilever piezoelectric energy harvester systems with a tip mass.

scholarly journals Design and Experimental Study of an L Shape Piezoelectric Energy Harvester

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
In-Ho Kim ◽  
Seon-Jun Jang ◽  
Hyung-Jo Jung
Keyword(s):  
Output Voltage ◽  
Energy Harvester ◽  
Performance Enhancement ◽  
Mechanical Strain ◽  
Electrical Energy ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Cantilevered Beam ◽  
Beam Type ◽  
Low Efficiency

Piezoelectric energy harvesters of cantilevered beam type are studied in various fields due to simplicity. In general, these systems obtain electrical energy from mechanical strain by bending of cantilevered beam. However, conventional systems have disadvantages that they have low efficiency in frequency regions other than resonance frequency. To overcome the limitations, various energy harvesters to apply performance enhancement strategies are proposed and investigated. In this paper, a frequency-changeable L shape energy harvester which is form connected cantilever beam and rigid arm is proposed and investigated. The conventional piezoelectric energy harvester exhibits the principal frequency in the simple bending mode whereas the proposed system features the twisting mode resulting in a higher output voltage than the conventional system. The proposed energy harvester is simplified to a two-degree-of-freedom model and its dynamics are described. How the length of a rigid bar affects its natural frequencies is also studied. To evaluate the performance of the system, experiments by using a vertical shaker and numerical simulation are carried out. As a result, it is shown that the natural frequency for a twisting mode decreases as the arm length increased, and the higher output voltage is generated comparing with those of the conventional energy harvester.

Performance of Galloping Piezoelectric Energy Harvesters With Square Bluff Body

2013 ◽  
Author(s):  
Felix Ewere ◽  
Gang Wang
Keyword(s):  
Experimental Data ◽  
Wind Tunnel ◽  
Mechanical Model ◽  
Bluff Body ◽  
Energy Harvester ◽  
Approximate Solutions ◽  
Wind Tunnel Tests ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Physical Insight

In this paper, we investigate a galloping piezoelectric energy harvester (GPEH) with a square bluff body. Comprehensive wind tunnel tests are conducted and experimental data are used to validate our analytical approximate solutions, which are derived from a coupled aero-electro-mechanical model. In addition, the effects of impact disturbances using a bump are investigated. The goal is to improve the performance of baseline GPEH. We expect to collect physical insight to design an optimal nonlinear GPEH configuration by placing bumps accordingly. Lessons learnt from this study will be used to improve the performance of future nonlinear GPEHs and lead to a practical device.

Flexible, Piezoelectric Aluminium-doped Zinc Oxide Energy Harvesters with Printed Electrodes for Wearable Applications

2021 ◽  
Vol 11 ◽  
Author(s):  
Muhammad Irsyad Suhaimi ◽  
Anis Nurashikin Nordin ◽  
Aliza Aini Md Ralib ◽  
Lai Ming Lim ◽  
Zambri Samsudin
Keyword(s):  
Zinc Oxide ◽  
Output Voltage ◽  
Energy Harvester ◽  
Wearable Sensors ◽  
Low Frequency ◽  
Design Parameters ◽  
Axis Orientation ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Cantilever Structure

Aims: Recent advancements in sensing technology and wireless communications have accelerated the development of the Internet of Things (IoT) which promote the usage of wearable sensors. An emerging trend is to develop self-sustainable wearable devices, thus eliminating the necessity of the user to carry bulky batteries. In this work, the development of a flexible piezoelectric energy harvester that is capable of harvesting energy from low frequency vibrations is presented. The target application of this energy harvester is for usage in smart shoes. Objectives: The objectives of this research is to design, fabricate and test an energy harvester on PET substrate using Aluminum Zinc Oxide as its piezoelectric layer. Methods: The energy harvester was designed as a cantilever structure using PET/AZO/Ag layers in d33 mode which can generate large output voltages with small displacements. The electrodes were designed as an interdigitated structure in which two significant design parameters were chosen, namely the effect of gap between electrodes, g and number of interdigital electrodes (IDE) pairs, N to the output voltage and resonant frequency. Results: The sputtered AZO on PET showed c-axis orientation at 002 peak with 2 values of 34.45° which indicates piezoelectric behaviour. The silver IDE pairs were screen-printed on the AZO thin film. Functionality of the device as an energy harvester was demonstrated by testing it using a shaker. The energy harvester was capable of generating 0.867 Vrms output voltage when actuated at 49.6 Hz vibrations. Conclusion: This indicates that the AZO thin films with printed silver electrodes can be used as flexible, d33 energy harvesters.

scholarly journals A Novel Piezoelectric Energy Harvester Using a Multi-Stepped Beam with Rectangular Cavities

2018 ◽  
Vol 8 (11) ◽  
pp. 2091 ◽  
Author(s):  
Ramalingam Usharani ◽  
Gandhi Uma ◽  
Mangalanathan Umapathy ◽  
Seung-Bok Choi
Keyword(s):  
Cantilever Beam ◽  
Output Voltage ◽  
Energy Harvester ◽  
Resonant Frequencies ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Stepped Beam ◽  
Operating Frequency Range ◽  
Critical Issues ◽  
A New Technique

In vibration-based piezoelectric energy harvesters, one of the major critical issues is increasing the bandwidth and output voltage simultaneously. This manuscript explores a new technique for broadening the operating frequency range and enhancing the output voltage of the piezoelectric material-based energy harvester by appropriate structural tailoring. The wide bandwidth and the improvement in harvested output are accomplished by means of a multi-stepped cantilever beam shaped with rectangular cavities. The harvester is mathematically modeled and analyzed for modal characteristics. It was demonstrated from the outcome that the first two consecutive mode frequencies could be brought closer and the output power was large at both the resonant frequencies compared to the regular cantilever beam energy harvester. The results obtained from experimentation were in agreement with analytical results.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

Sign in / Sign up

Export Citation Format

Share Document