scholarly journals Experimental Methodology and Facility for the J69-Engine Performance and Emissions Evaluation Using Jet A1 and Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4530 ◽  
Author(s):  
Gabriel Talero ◽  
Camilo Bayona-Roa ◽  
Giovanny Muñoz ◽  
Miguel Galindo ◽  
Vladimir Silva ◽  
...  
Keyword(s):  
Fossil Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Experimental Tests ◽  
Experimental Methodology ◽  
Injection System ◽  
Small Scale ◽  
Gas Temperature ◽  
Maximum Increase

Aeronautic transport is a leading energy consumer that strongly contributes to greenhouse gas emissions due to a significant dependency on fossil fuels. Biodiesel, a substitution of conventional fuels, is considered as an alternative fuel for aircrafts and power generation turbine engines. Unfortunately, experimentation has been mostly limited to small scale turbines, and technical challenges remain open regarding operational safety. The current study presents the facility, the instrumentation, and the measured results of experimental tests in a 640 kW full-scale J69-T-25A turbojet engine, operating with blends of Jet A1 and oil palm biodiesel with volume contents from 0% to 10% at different load regimes. Findings are related to the fuel injection system, the engine thrust, and the emissions. The thrust force and the exhaust gas temperature do not expose a significant variation in all the operation regimes with the utilization of up to 10% volume content of biodiesel. A maximum increase of 36% in fuel consumption and 11% in injection pressure are observed at idle operation between B0 and B10. A reduction of the CO and HC emissions is also registered with a maximum variation at the cruise regime (80% Revolutions Per Minute—RPM).

scholarly journals Theoretical study to determine the proper injection system for upgrading fuel system of diesel engine om357 to common rail system

2018 ◽  
Vol 7 (4) ◽  
pp. 2594
Author(s):  
Razieh Pourdarbani ◽  
Ramin Aminfar
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail System ◽  
Common Rail Injection System ◽  
Multi Stage

In this research, we tried to investigate all the fuel injection systems of diesel engines in order to select the most suitable fuel injection system for the OM357 diesel engine to achieve the highest efficiency, maximize output torque and reduce emissions and even reduce fuel consumption. The prevailing strategy for this study was to investigate the effect of injection pressure changes, injection timing and multi-stage injection. By comparing the engines equipped with common rail injection system, the proposed injector for engine OM357 is solenoid, due to the cost of this type of injector, MAP and controller (ECU). It is clear that this will not be possible only with the optimization of the injection system, and so other systems that influence engine performance such as the engine's respiratory system and combustion chamber shape, etc. should also be optimized. 

Numerical Investigation on LNG Injection in a SI-ICE

2018 ◽  
Author(s):  
Gianluca Pasini ◽  
Stefano Frigo ◽  
Marco Antonelli ◽  
Maria Berardi
Keyword(s):  
Natural Gas ◽  
Fossil Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Peak Torque ◽  
Cryogenic Liquid ◽  
Volumetric Efficiency ◽  
Injection System ◽  
Intake Manifold ◽  
Si Engines

Since the beginning of this century, Liquefied Natural Gas (LNG) has been attracting more and more attention as a cleaner energy alternative to other fossil fuels, mainly due to the possibility to transport it over longer distances than natural gas in pipelines and lower environmental impact than other liquid fuels. It is expected that this trend in the use of LNG will lead to steady increases in demand over the next few decades. At present, in the automotive sector, natural gas is employed as fuel in spark-ignited (SI) engines in the gas phase (CNG) adopting port-fuel injection system (PFI) in the intake manifold, with the main result of reducing CO2 emissions by up to 20%, compared with gasoline operation. However, SI engines which are operated in this manner suffer loss of peak torque and power due to a reduction in volumetric efficiency. Direct-Injection (DI) inside the cylinder can overcome this drawback by injecting CNG after intake valve closure. Another strategy could be the injection of natural gas in the liquid phase, both in PFI or DI mode. The injected fuel evaporation cools down the intake air; increasing the charge density with a substantial improvement in the engine volumetric efficiency and delivered power. However, at present, injection systems dedicated to cryogenic injection of natural gas are still in the prototype state. In the present study, the volumetric efficiency and performance of a turbocharged, LNG fuelled SI-ICE were numerically analysed both in the cases of DI and PFI modes and compared with the results of a conventional CNG system. Various fuel injection timings and injector position were analysed. The engine performance was evaluated by means of a one-dimensional model developed with the simulation program GT-Power, while the verification of the LNG-air mixture characteristics was carried out with the commercial code Aspen HYSIS. The numerical activity has shown that gaseous DI, before inlet valves closing, gives the worst result since methane, once injected into the cylinder, expands hindering the entry of air. On the other side, liquid PFI represents the best configuration to maximize the volumetric efficiency and therefore the engine power. All the technological issues related to a cryogenic liquid methane injection system were not taken into consideration in this study.

Effect of process parameters on the diesel engine performance fuelled with Prosopis juliflora biodiesel response surface methodology approach

2021 ◽  
pp. 095440892110430
Author(s):  
Abhishek Sharma ◽  
Avdhesh Tyagi ◽  
Yashvir Singh ◽  
Nishant K Singh ◽  
Navneet K Pandey
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Prosopis Juliflora ◽  
Injection Timing ◽  
Gas Temperature ◽  
Input Parameters ◽  
Fuel Injection Pressure

The rapid consumption of crude oil and resulting pollution are very severe problems in modern energy sectors. To meet these global problems, biodiesels obtained from non-edible plants can play a very crucial role. Keeping this idea in mind the present study focuses on making some efforts for the best utilization of innovative blends of Prosopis juliflora biodiesel in the operation of diesel engines. Four engine input parameters viz. fuel injection pressure (16–24 MPa), P. Juliflora biodiesel blends (0–10%), shaft loads (20–100%) and injection timing (15–31°bTDC (before top dead centre)) are selected for optimization process. The experiments were executed in accordance with response surface methodology. The results of the experiments revealed that the optimum combination for engine input parameters were at fuel injection timing 30°bTDC, fuel injection pressure 22 MPa, 4% P. juliflora biodiesel blending at 59% of engine load to achieve best performance. The individual desirability of brake thermal efficiency, brake specific fuel consumption, exhaust gas temperature and peak cylinder pressure were found to be 0.888, 0.949, 0.624 and 0.749, respectively, and the composite desirability of engine responses was found to be 0.7923 which makes the results acceptable.

scholarly journals Optimization of Fuel Injection Parameters of Moringa oleifera Biodiesel-Diesel Blend for Engine-Out-Responses Improvements

Symmetry ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 982
Author(s):  
Yew Heng Teoh ◽  
Heoy Geok How ◽  
Farooq Sher ◽  
Thanh Danh Le ◽  
Hwai Chyuan Ong ◽  
...  
Keyword(s):  
Diesel Engines ◽  
Fossil Fuels ◽  
Moringa Oleifera ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Single Step ◽  
Rapid Decline ◽  
Fuel Blend ◽  
Combustion Dynamics ◽  
Rsm Optimization

Biodiesel has gained popularity in diesel engines as a result of the rapid decline of fossil fuels and population growth. The processing of biodiesel from non-edible Moringa Oleifera was investigated using a single-step transesterification technique. Both fuels had their key physicochemical properties measured and investigated. In a common-rail diesel engine, the effects of MB50 fuel blend on the symmetric characteristics of engine-out responses were evaluated under five load settings and at 1000 rpm. As compared to standard diesel, MB50 increased brake thermal efficiency (BTE), and nitrogen oxides (NOx) emissions while lowering brake specific fuel consumption (BSFC), and smoke emissions for all engine loads. A further study of injection pressure and start of injection (SOI) timing for MB50 fuel was optimized using response surface methodology (RSM). The RSM optimization resulted in improved combustion dynamics due to symmetry operating parameters, resulting in a simultaneous decrease in NOx and smoke emissions without sacrificing BTE. RSM is an efficient optimization method for achieving optimal fuel injection parameter settings, as can be deduced. As a result, a clearer understanding of the use of MB50 fuel in diesel engines can be given, allowing for the best possible engine efficiency.

scholarly journals Organization of Six-Cylinder Tractor Diesel Working Process

2021 ◽  
Vol 20 (5) ◽  
pp. 427-433
Author(s):  
G. M. Kuharonak ◽  
M. Klesso ◽  
A. Predko ◽  
D. Telyuk
Keyword(s):  
Combustion Chamber ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System ◽  
Rotary Valve ◽  
Original Design ◽  
Working Process ◽  
Common Rail System

The purpose of the work is to consider the organization of the working process of six-cylinder diesel engines with a power of 116 and 156 kW and exhaust gas recirculation. The following systems and components were used in the experimental configurations of the engine: Common Rail BOSСH accumulator fuel injection system with an injection pressure of 140 MPa, equipped with electro-hydraulic injectors with seven-hole nozzle and a 500 mm3 hydraulic flow; direct fuel injection system with MOTORPAL fuel pump with a maximum injection pressure of 100 MPa, equipped with MOTORPAL and AZPI five-hole nozzle injectors; two combustion chambers with volumes of 55 and 56 cm3 and bowl diameters of 55.0 and 67.5 mm, respectively; cylinder heads providing a 3.0–4.0 swirl ratio for Common Rail system, 3.5–4.5 for mechanical injection system. The recirculation rate was set by gas throttling before the turbine using a rotary valve of an original design. The tests have been conducted at characteristic points of the NRSC cycle: minimum idle speed 800 rpm, maximum torque speed 1600 rpm, rated power speed 2100 rpm. It has been established that it is possible to achieve the standards of emissions of harmful substances: on the 116 kW diesel engine using of direct-action fuel equipment and a semi-open combustion chamber; on the 156 kW diesel using Common Rail fuel supply system of the Low Cost type and an open combustion chamber.

Experimental investigation of dwell time characteristics in high-pressure double-solenoid-valve fuel injection system

2019 ◽  
Vol 233 (13) ◽  
pp. 3281-3292
Author(s):  
Dan Xu ◽  
Qing Yang ◽  
Xiaodong An ◽  
Baigang Sun ◽  
Dongwei Wu ◽  
...  
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Solenoid Valve ◽  
Injection System ◽  
Fuel Injection System ◽  
Pilot Injection ◽  
Main Injection ◽  
Injection Interval ◽  
The Difference ◽  
Variation Rule

The double-solenoid-valve fuel injection system consists of an electronic unit pump and an electronic injector. It can realize the separate control of fuel supply and injection and has the advantages of adjusting pressure by cycle and flexible controlling of the injection rate. The interval angle between the pilot and main injection directly affects the action degree and the characteristics of two adjacent injections, affecting engine performance. This work realizes multiple injection processes on the test platform of a high-pressure double-solenoid-valve fuel injection system, with maximum injection pressure reaching 200 MPa. In this study, the interval between driven current signal of pilot injection termination and that of main injection initiation is defined as the signal interval (DT1), whereas the interval between pilot injection termination and main injection initiation is defined as the injection interval (DT2). The differences between the signal and the injection intervals are calculated, and the variation rule of the difference with respect to the signal interval is analyzed. Results show that the variation rule of the difference with the signal interval first decreases, then increases, and finally decreases. The variation rule of the delay angle from the start of needle movement to the start of fuel injection is found to be the root cause of this rule. The influence of the injection pressure on needle deformation and fuel flow rate of the nozzle results in the variation rule. In addition, the influence of the cam speed, temperature, and pipe length on the difference between the signal and injection interval is determined. This research provides guidance for an optimal control strategy of the fuel injection process.

Automated Engine Calibration Optimization Using Online Extremum Seeking

2018 ◽  
Author(s):  
Ripudaman Singh ◽  
Andrew Mansfield ◽  
Margaret Wooldridge
Keyword(s):  
Control Parameter ◽  
Gasoline Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Extremum Seeking ◽  
Injection System ◽  
Test Time ◽  
Injection Timing ◽  
Promising Alternative ◽  
Non Linear System

Emissions compliance during engine start-up conditions is a major obstacle for current automotive manufacturers across global markets. The challenges to meeting emissions targets are both due to increasingly stringent regulations and the difficulty in developing control strategies for a high degree-of-freedom and highly non-linear system. Online extremum-seeking (ES) methods offer a promising alternative to traditional optimization based on design-of-experiment based automotive calibration. With extremum-seeking methods, results from all prior experiments are used to intelligently and efficiently generate the next iteration of the control parameter(s). In this work, the applicability of the online extremum-seeking method is explored to optimize five performance variables (injection timing for two injection events, the injection fuel mass divided between the first and second injection events, air-fuel equivalence ratio and exhaust cam timing) to minimize brake specific fuel consumption while imposing different constraints on NOx emissions. The experiments were conducted using a production turbocharged four-cylinder gasoline engine with an advanced fuel injection system. The results show the utility of the ES strategy to quickly identify optimal control parameter combinations and the emissions and engine performance improvements during the calibration process. The results also demonstrate the dramatic benefit of the ES calibration strategy in terms of test time required.

Effect of the Fuel Injection Strategy on Diesel Particulate Filter Regeneration in a Single-Cylinder Diesel Engine

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

Sign in / Sign up

Export Citation Format

Share Document