scholarly journals Influence of Hydrophobic Fin Configuration in Thermal System in Relation to Electronic Device Cooling Applications

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1631
Author(s):  
Shahzada Zaman Shuja ◽  
Bekir Sami Yilbas ◽  
Hussain Al-Qahtani
Keyword(s):  
Nusselt Number ◽  
Pressure Drop ◽  
Electronic Device ◽  
Cooling System ◽  
Flow Analysis ◽  
Flow Distribution ◽  
Reynolds Numbers ◽  
Solution Domain ◽  
Uniform Flow Distribution ◽  
Temperature Parameter

In this study, heat and flow analysis of the cooling system incorporating fins with hydrophilic and hydrophobic wetting surfaces has been considered in relation to electronic cooling applications. Temperature and velocity fields in the solution domain are simulated for various fin numbers and sizes. A temperature parameter is introduced to assess the thermal performance of the system. Fin count is introduced to formulate the number of fins in the solution domain. The Nusselt number and pressure drop between the inlet and exit ports due to different fin configurations of the cooling system for various fin counts are presented. It is found that the temperature parameter attains high values for large sizes and small fin counts, which is more pronounced for low Reynolds numbers. Increasing number of fins results in almost uniform flow distribution among the fin, which is more pronounced for the hydrophobic fin configuration. The Nusselt number attains larger values for the hydrophilic fin configuration than that corresponding to the hydrophobic fin, and it attains a peak value for certain arrangement of fin count, which differs with the Reynolds number. The pressure drop between the inlet and exit ports reduces for hydrophobic fin; hence the slip velocity introduced for hydrophobic fin improves the pressure drop by 6% to 16% depending on the fin counts in the cooling system.

Manifold Design for Micro-Channel Cooling With Uniform Flow Distribution

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Stephen A. Solovitz ◽  
Jeffrey Mainka
Keyword(s):  
Power Law ◽  
Cooling System ◽  
Heat Removal ◽  
Flow Distribution ◽  
Reynolds Numbers ◽  
Electronic Systems ◽  
Pressure Drops ◽  
Developing Flow ◽  
Micro Channels ◽  
Uniform Flow Distribution

High-power electronic systems often require temperature uniformity for optimal performance. While many advanced cooling systems, such as micro-channels, result in significant heat removal, they are also susceptible to flow mal-distribution that can impact the local temperature variation on a device. By examining the pressure drops through each flow path in a multi-channel cooling system, an analytical model is predicted for the optimal manifold shape to produce uniform velocities. This is a simple power law, whose exponent depends on the flow regime in the manifold passages. The model is validated for laminar fully developed conditions using a series of computational simulations. With the power law design, the speeds in a parallel channel design are uniformly distributed at low Reynolds numbers, with a standard deviation of less than 3% of the overall mean channel speed. At higher Reynolds numbers, some mal-distribution is observed due to developing flow conditions, but it is not as significant as with typical untapered designs.

Enhancement of Heat Transfer to an Air Jet Impinging on a Flat Plate

Volume 1 ◽  
2004 ◽  
Author(s):  
D. P. Mishra ◽  
D. Mishra
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Flat Plate ◽  
Average Nusselt Number ◽  
Cooling System ◽  
Reynolds Numbers ◽  
Heated Plate ◽  
Maximum Heat ◽  
Air Jet ◽  
Maximum Heat Transfer

An experimental investigation of the impinging jet cooling from a heated flat plate has been carried out for several Reynolds numbers (Re) and nozzle to plate distances. The present results indicate that the maximum heat transfer occurs from the heated plate at stagnation point and decreases with radial distances for all cases. The maximum value of the stagnation as well as average Nusselt number is found to occur at separation distance, H/D = 6.0 for Re = 55000. An attempt is also made to study effects of nozzle exit configuration on the heat transfer using a sharp edged orifice for same set of Reynolds numbers and nozzle to plate distance. The stagnation Nusselt numbers of sharp orifice jets are found to be enhanced by around 16–21.4% in comparison to that of square edged orifice. However, the enhancement in the average Nusselt number of sharp orifice is found to be in the range of 7–18.9% as compared to the square edged orifice. The maximum enhancement of 18.9% in average Nu is achieved for Re = 55 000 at H/D = 6. Two separate correlations in terms of Nuo, Re, H/D for both square and sharp edged orifice are obtained which will be useful for designing impinging cooling system.

Analysis of Flow Mal-Distribution in a Cross-Flow Heat Exchanger

2014 ◽  
Vol 592-594 ◽  
pp. 1428-1432 ◽  
Author(s):  
Krishna P. Mohan ◽  
Shekar M. Santosh ◽  
M. Ramakanth ◽  
M.R. Thansekhar ◽  
M. Venkatesan
Keyword(s):  
Heat Exchanger ◽  
Pressure Drop ◽  
Cross Flow ◽  
Flow Distribution ◽  
Ansys Fluent ◽  
Commercial Code ◽  
Uniform Flow Distribution ◽  
Flow Heat ◽  
Channel Assembly ◽  
Uniform Fluid

Flow mal-distribution is defined as the non-uniform fluid flow distribution among the parallel channels having a common header. Flow mal-distribution is present in every header channel assembly. This mal-distribution has a significant effect on the performance of the heat exchanger by increasing the pressure drop and affecting the heat transfer characteristics. However, in designing a heat exchanger, a uniform flow distribution in each channel is assumed. The present work attempts to reduce the flow mal-distribution in a cross flow heat exchanger. A numerical analysis is done using a commercial code ANSYS FLUENT 3D and the results are validated experimentally. A parametric study is done by changing the size of the channels within the heat exchanger so as to reduce the flow mal-distribution. The effect of varying channel size on flow mal-distribution and pressure drop across the heat exchanger is studied and a geometry with reduced flow mal-distribution is found.

Hydrodynamic and Thermal Performance of Microchannels With Different Staggered Arrangements of Cylindrical Micro Pin Fins

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Ali Mohammadi ◽  
Ali Koşar
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Reynolds Numbers ◽  
Design Parameters ◽  
Interaction Patterns ◽  
Wake Region ◽  
Pin Fins ◽  
Micro Pin Fins

This study focuses on microheat sinks with different staggered arrangements of micro pin fins (MPFs). A rectangular microchannel with the dimensions of 5000 × 1500 × 100 μm3 (l′ × w′ × h′) was considered for all the configurations while different MPF diameters, height over diameter ratio (H/D), and longitudinal and transversal pitch ratios (SL/D and ST/D) were considered in different arrangements. Using the ansys fluent 14.5 commercial software, the simulations were done for different Reynolds numbers between 20 and 160. A constant heat flux of 30 W/cm2 was applied through the bottom heating section. The performances of the microheat sinks were evaluated using design parameters, namely pressure drop, friction factor, Nusselt number, and thermal-hydraulic performance index (TPI). The effect of each geometrical parameter as well as wake-pin fin interaction patterns were carefully studied using the streamline patterns and temperature profiles of each configuration. The results reveal a great dependency of trends in pressure drops and Nusselt numbers on the wake region lengths as well as the local velocity and pressure gradients. Moreover, the wake region lengths mostly contribute to the increase in obtained pressure drop and Nusselt number with Reynolds number. Although an increase in the H/D and SL/D ratios results in an increase and a decrease in pressure drop, respectively, the effect on the Nusselt number depends on other geometrical parameters and Reynolds number. A larger ST/D ratio generally results in a decrease in the pressure drop and Nusselt number. Finally, while the friction factor decreases with Reynolds number, two different trends are seen for the TPI values of configurations with the H/D ratio of 1 and 2 (D = 100 and 50 μm). While the trend in the TPIs is increasing for Reynolds numbers between 20 and 40, it reverses for higher Reynolds numbers with a steeper slope in the configurations with the ST/D ratio of 1.5.

NUMERICAL STUDY OF THE EFFECT OF AREA OF MANIFOLD AND INLET/OUTLET FLOW ARRANGEMENT 0N FLOW DISTRIBUTION IN PARALLEL RECTANGULAR MICROCHANNEL COOLING SYSTEM

2017 ◽  
Vol 79 (7-3) ◽  
Author(s):  
Amirah M. Sahar ◽  
A. I. M. Shaiful
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Cooling System ◽  
Numerical Study ◽  
Flow Distribution ◽  
Fluid Temperature ◽  
Rectangular Microchannel ◽  
Temperature Distributions ◽  
Micro Channels ◽  
Parallel Microchannels

Parallel microchannels have been widely used in cooling of compact electronic equipment due to large contact area with liquid and availability of large mass of fluid to carry away heat. However, understanding of flow distribution for microchannel parallel system is still unclear and there still lack of studies give a clear pictures to understand the complex flow features which cause the flow maldistribution. Generally, the geometrical structure of the manifold and micro channels play an important role in flow distribution between micro channels, which might affects the heat and mass transfer efficiency, even the performance of micro exchangers. A practical design of exchanger basically involves the selection of an optimized solution, keeping an optimal balance between gain in heat transfer and pressure drop penalty. A parallel microchannels configurations consisting inlet and outlet rectangular manifold were simulated to study flow distribution among the channels were investigated numerically by using Ansys Fluent 14.5. The numerical results was validated using existing experimental data and showed a similar trend with values 1% higher than experimental data. The influence of inlet/outlet manifold area and inlet/outlet arrangement on flow distribution in channels were carried out in this study. Based on the predicted flow non-uniformity value, 𝜙, Z- type flow arrangement exhibits higher value of 𝜙, which is 8%, followed by U-type, 2.6% and the I-type, 2.49%. Thus, a better uniformity of velocity and temperature distributions can be achieved in I-shape flow arrangement. The behavior of the flow distributions inside channels is due to the vortices that occurred at manifold. Besides comparing the pressure drop for case 1(D1) and case 2(D2), it is worth to mention that, as the area of inlet and outlet manifold decrease by 50%, the pressure drop is increasing about 5%. However, the inlet/outlet area of manifold on velocity and fluid temperature distributions was insignificant.

Heat Transfer and Flow Structure in a Latticework Duct With Different Sidewalls

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Wei Du ◽  
Lei Luo ◽  
Songtao Wang ◽  
Jian Liu ◽  
Bengt Sunden
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Flow Structure ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Pressure Side ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Abstract Heat transfer characteristics in a latticework duct with various sidewalls are numerically investigated. The crossing angle is 90 deg and the number of subchannels is eleven on both the pressure side and suction side for each latticework duct. The thickness of the ribs is 8 mm and the distance between adjacent ribs is 24 mm. The investigation is conducted for various Reynolds numbers (11,000 to 55,000) and six different sidewalls. Flow structure, pressure drop, and heat transfer characteristics are analyzed. Results revealed that the sidewall has significant effects on heat transfer and flow structure. The triangle-shaped sidewall provides the highest Nusselt number accompanied by the highest friction factor. The sidewall with a slot shows the lowest friction factor and Nusselt number. An increased slot width decreased the Nusselt number and friction factor simultaneously.

Flow Distribution and Pressure Drop in Steady Airflow Through a Selective Laser Sintered Human Tracheobronchial Airway Model

2003 ◽  
Author(s):  
Kah-Hoe Tan ◽  
Ramkumar N. Parthasarathy ◽  
M. Cengiz Altan ◽  
David L. Johnson ◽  
R. E. Clinkenbeard
Keyword(s):  
Pressure Drop ◽  
Static Pressure ◽  
Flow Distribution ◽  
Reynolds Numbers ◽  
Flow Rates ◽  
Physiological Flow ◽  
Static Pressure Difference ◽  
The Mean ◽  
The Relationship ◽  
Airway Model

The flow distribution and pressure drop of steady airflow in the human central airways were studied experimentally using an anatomically correct, selective laser sintered (SLS) human tracheobronchial airway model. Measurements were made for tracheal flow rates ranging from 0.1 to 2.67 liters per second, which correspond to normal physiological flow ranges. The mean air velocities at the exit orifices of the airway model were detected by means of a pitot static tube connected to a pressure transducer. The flow rates, the average velocities, and the Reynolds numbers in each branch of the airway model were then computed. In addition, the static pressure difference between the trachea and the airway exits was measured. The experimental measurements were used to determine the relationship between pressure drop and flow rate. The ratio of inlet to total exit area of the model was identified as a significant factor that influenced the pressure drop. The results obtained in the present study will be particularly useful for validating computational studies.

Heat Transfer and Fluid Flow Analysis of Interrupted-Wall Channels, With Application to Heat Exchangers

1977 ◽  
Vol 99 (1) ◽  
pp. 4-11 ◽  
Author(s):  
E. M. Sparrow ◽  
B. R. Baliga ◽  
S. V. Patankar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
High Performance ◽  
Numerical Solutions ◽  
Flow Analysis ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Operating Conditions ◽  
Wide Range

An analysis has been made of laminar flow and heat transfer in channels whose walls are interrupted periodically along the streamwise direction. Such channels are frequently employed in high-performance compact heat exchangers. Numerical solutions of the mass, momentum, and energy conservation equations yielded local heat transfer and pressure drop results. These results were obtained for a range of Reynolds numbers and for several values of a dimensionless geometrical parameter characterizing the streamwise length L of the individual plate segments which make up the interrupted walls. The Prandtl number was fixed at 0.7 for all the calculations. The basic heat transfer and pressure drop results were employed to investigate whether an interrupted-wall channel experiences an augmented heat transfer rate compared with that for a parallel plate channel. For conditions of equal heat transfer surface area and equal pumping power, appreciably higher heat transfer rates prevailed in the interrupted-wall channel for a wide range of operating conditions. The augmentation was especially marked for relatively short channels and high Reynolds numbers. The results also demonstrated the existence of a new type of fully developed regime, one that is periodic. At sufficiently large downstream distances, the velocity and temperature profiles repeat their values at successive axial stations separated by a distance 2L and, in addition, the average heat transfer coefficient for a plate segment takes on a constant value.

Thermal Transport in a Microchannel Exhibiting Ultrahydrophobic Microribs Maintained at Constant Temperature

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
D. Maynes ◽  
B. W. Webb ◽  
J. Davies
Keyword(s):  
Nusselt Number ◽  
Pressure Drop ◽  
Laminar Flow ◽  
Constant Temperature ◽  
Thermal Transport ◽  
Flow Direction ◽  
Relative Size ◽  
Reynolds Numbers ◽  
Frictional Pressure Drop ◽  
Smooth Channel

This paper presents numerical results exploring the periodically repeating laminar flow thermal transport in a parallel-plate microchannel with ultrahydrophobic walls maintained at constant temperature. The walls considered here exhibit alternating microribs and cavities positioned perpendicular to the flow direction. Results describing the thermally periodically repeating dynamics far from the inlet of the channel have been obtained over a range of laminar flow Reynolds numbers and relative microrib/cavity module lengths and depths in the laminar flow regime. Previously, it has been shown that significant reductions in the overall frictional pressure drop can be achieved relative to the classical smooth channel laminar flow. The present predictions reveal that the overall thermal transport is also reduced as the relative size of the cavity region is increased. The overall Nusselt number behavior is presented and discussed in conjunction with the frictional pressure drop behavior for the parameter range explored. The following conclusions can be made regarding thermal transport for a constant temperature channel exhibiting ultrahydrophobic surfaces: (1) Increases in the relative cavity length yield decreases in the Nusselt number, (2) increasing the relative rib/cavity module length yields a decrease in the Nusselt number, and (3) decreases in the Reynolds number result in smaller values of the Nusselt number.

scholarly journals Experimental Pressure Drop and Heat Transfer in a Rectangular Channel With a Sinusoidal Porous Screen

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Gazi I. Mahmood ◽  
Carey J. Simonson ◽  
Robert W. Besant
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Air Temperature ◽  
Rectangular Cross Section ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Heated Wall ◽  
Mean Flow

Experiments are conducted to investigate turbulence enhancing effects of a porous mesh-screen with a sinusoidal shape normal to the flow direction inside a rectangular cross section air channel at low Reynolds numbers (i.e., Re = 1360–3800). The baseline measurements are obtained at the same channel and Reynolds numbers without the screen present. The surface of the screen pores are oriented parallel to the mean flow. Data are presented for the total and wall-static pressure drop along the channel, Nusselt number distributions on the heated wall at several constant heat rates, and air temperature distributions at the channel exit with and without (baseline cases) the screen. The heat transfer measurements are obtained with one wall heated as well as two parallel walls heated to simulate different applications for air channels in the flat plate heat exchangers. The results indicate that the ratio of screen channel to baseline Nusselt number (Nu/Nu0) and the ratio of screen channel to baseline friction factor (f/f0) increase with the Reynolds number (Re). The fully developed Nu/Nu0 is 2.0–2.5 as the fully developed f/f0 is 4.4 at 3100 < Re ≤ 3800. However, the screen channel heat convection performance index, (Nu/Nu0)/(f/f0)1/3 is only greater than 1.0 when Re > 2500 which is the design objective of reducing the pumping power and heat transfer area in the channel. Nonetheless, the screen insert is only beneficial to augment the convective heat transfer in the channel over the range of transition Reynolds number tested. The average total pressure drop across the channel and average exit air temperature suggest that the screen insert promotes good mixing of fluid across the channel for the Reynolds numbers tested.

Sign in / Sign up

Export Citation Format

Share Document