scholarly journals Fly Ash as an Ingredient in the Contaminated Soil Stabilization Process

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 565
Author(s):  
Kamil Banaszkiewicz ◽  
Tadeusz Marcinkowski ◽  
Iwona Pasiecznik
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Contaminated Soil ◽  
Coal Combustion ◽  
Soil Stabilization ◽  
Soil Mass ◽  
Flame Ionization ◽  
Benzene Concentration ◽  
Average Compressive Strength

Fly ash is the main by-product of coal combustion characterized by a large specific surface area. In addition to oxides, it also contains unburned coal and trace elements. This study aimed to investigate the possibility of using fly ash from pit-coal combustion (CFA) for the treatment of benzene-contaminated soil (S). The CFA was used as a mixture with Portland cement (PC) (70% PC + 30% CFA). The soil was treated with a PC-CFA mixture in amounts of 40, 60, and 80% of soil mass. During the process, the concentration of benzene was monitored with the flame-ionization detector. Produced monoliths (S+(PC-CFA)x) were tested for compressive strength and capillary water absorption. The experiment confirmed that the PC-CFA mixture limited benzene emission. The highest reduction in benzene concentration (34–39%) was observed for samples treated with the PC-CFA mixture in an amount of 80% (S+(PC-CFA)80). The average compressive strength of monoliths S+(PC-CFA)40, S+(PC-CFA)60, and S+(PC-CFA)80 was 0.57, 4.53, and 6.79 MPa, respectively. The water absorption values were in the range of 15–22% dm.

Assessment to the Solid to Liquid Ratios on the Soil Strength and Water Absorption of the Kedah’s Soil

2016 ◽  
Vol 841 ◽  
pp. 59-64 ◽  
Author(s):  
Hazamaah Nur Hamzah ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Cheng Yong Heah ◽  
Mohd Remy Rozainy Arif Zainol ◽  
Kamarudin Hussin
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Alkaline Solution ◽  
Room Temperature ◽  
Soil Stabilization ◽  
Soft Soil ◽  
Constant Ratio ◽  
Liquid Ratio ◽  
Naoh Solution

The purpose of this paper is to assess the solid to liquid ratios on the compressive strength and water absorption of Kedah’s soil by using geopolymerization method. Fly ash and soft soil were mixed with alkaline activators namely sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) for preparing stabilize the soil sample. The geopolymerization process for soil stabilization was synthesized by the activation of fly ash and soil with alkaline solution at four different solid to liquid ratios which were 1.5, 2.0, 2.5, and 3.0 at a specific constant ratio of Na2SiO3/NaOH solution of 0.5. The compressive strength up to 4.77 MPa was obtained at 3.0 of solid to liquid ratio and the water absorption has become increasingly lower to 2.28% as the ratio of solid to liquid increases in 7 days curing at room temperature.

The Latest Research in Mongolia on the Utilization of Coal Combustion By-Products

2021 ◽  
Vol 323 ◽  
pp. 8-13
Author(s):  
Jadambaa Temuujin ◽  
Damdinsuren Munkhtuvshin ◽  
Claus H. Ruescher
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Thermal Power ◽  
Thermal Power Plants ◽  
Power Stations ◽  
Thermal Power Stations ◽  
Coal Ashes ◽  
By Products

With a geological reserve of over 170 billion tons, coal is the most abundant energy source in Mongolia with six operating thermal power stations. Moreover, in Ulaanbaatar city over 210000 families live in the Ger district and use over 800000 tons of coal as a fuel. The three thermal power plants in Ulaanbaatar burn about 5 million tons of coal, resulting in more than 500000 tons of coal combustion by-products per year. Globally, the ashes produced by thermal power plants, boilers, and single ovens pose serious environmental problems. The utilization of various types of waste is one of the factors determining the sustainability of cities. Therefore, the processing of wastes for re-use or disposal is a critical topic in waste management and materials research. According to research, the Mongolian capital city's air and soil quality has reached a disastrous level. The main reasons for air pollution in Ulaanbaatar are reported as being coal-fired stoves of the Ger residential district, thermal power stations, small and medium-sized low-pressure furnaces, and motor vehicles. Previously, coal ashes have been used to prepare advanced materials such as glass-ceramics with the hardness of 6.35 GPa, geopolymer concrete with compressive strength of over 30 MPa and zeolite A with a Cr (III) removal capacity of 35.8 mg/g. Here we discuss our latest results on the utilization of fly ash for preparation of a cement stabilized base layer for paved roads, mechanically activated fly ash for use in concrete production, and coal ash from the Ger district for preparation of an adsorbent. An addition of 20% fly ash to 5-8% cement made from a mixture of road base gave a compressive strength of ~ 4MPa, which exceeds the standard. Using coal ashes from Ger district prepared a new type of adsorbent material capable of removing various organic pollutants from tannery water was developed. This ash also showed weak leaching characteristics in water and acidic environment, which opens up an excellent opportunity to utilize.

PEMANFAATAN LIMBAH KOTORAN SAPI SEBAGAI PENGGANTI SEBAGIAN SEMEN DALAM PEMBUATAN BATAKO

2020 ◽  
Vol 15 (2) ◽  
pp. 53-57
Author(s):  
Kiki Kurniawan ◽  
Prihantono Prihantono ◽  
Rosmawita Saleh
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Mean Value ◽  
Cow Dung ◽  
A Value ◽  
Average Water ◽  
Hollow Brick ◽  
Average Compressive Strength

The results showed the use of cow dung waste can increase the compressive strength of hollow brick from any composition of waste. Hollow brick with cow dung substitution of 0% has an average compressive strength value 44.75 Kg/Cm2 has an average water absorption of 14.31%, hollow brick with cow dung substitution of 5% has a value of compressive strength average 47.47 Kg/Cm2 has an average water absorption of 15.67%, Batako perforation with cow dung substitution of 7.5% has an average compressive strength value of 51.83 Kg/Cm2 has the absorption water averaging 13.71%, batako perforated with substitution of cow dung waste of 10% has an average compressive strength value 53.81 Kg/Cm2 has an average water absorption of 10.04%, hollow brick with substitution cow dung waste of 12.5% has an average compressive strength value of 50.66 Kg/Cm2 has an average water absorption of 23.6%, hollow brick with cow dung substitution of 15% average 48.84 Kg/Cm2 has an average water absorption of 19.72%. The optimum compressive strength value was obtained from percentage substitution of cow dung waste at 10% with mean value of compressive strength 53,81 Kg/Cm2 with average water absorption 10,04%.

scholarly journals BATAKO LUMPUR LAPINDO SEBAGAI ALTERNATIF MATERIAL PASANGAN DINDING

2013 ◽  
Vol 10 (1) ◽  
Author(s):  
Rofikatul Karimah
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Building Material ◽  
Class I ◽  
Test Result ◽  
Made In

Block made of mud is a building material used in making wall for building that is made fromsand, cement, and fly ash using certain percentage mud in sand. This research aimed to know theeffect of the use of lapindo mud towards the compressive strength, the absorption of block waterwith the mud dosage in sand are: 0%, 10%, 20%, 30%, and 40%. This research was an experimentalresearch; each design was made in size 10x20x40 cm using 5% of fly ash and without fly ash.The result of this research showed that the highest compressive strength was raised in 10%mud in sand with 5% fly ash that was 195 kg/cm2 or increased about 3.44 kg/cm2 within increasingpercentage about 10.651% towards the compressive of block without lapindo mud with 5% of flyash, and was included in class I quality of block. While for the 30% and 40% mud percentage islower compared with normal compressive strength of block. The test result of water absorption oflapindo mud block showed the higher value than 20% for lapindo mud block with 5% fly ash, inframing the mud blocks as the wall, those blocks need to be soaked first because the absorptionvalue of block is higher than 20%. Lapindo mud block without 5% fly ash has bricks water absorptionless than 20%, while in framing those bricks, they don’t need to be soaked because the absorptionof brick if lower than 20%. By using fly ash in mud block, we can get the higher compressivestrength and the lower water absorption.Keyword: Porong Mud, Block, Fly Ash, Compressive Strength, Absorption

scholarly journals Biofuel Combustion Fly Ash Influence on the Properties of Concrete

2016 ◽  
Vol 7 (5) ◽  
pp. 546-550
Author(s):  
Aurelijus Daugėla ◽  
Džigita Nagrockienė ◽  
Laurynas Zarauskas
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Water Absorption ◽  
Frost Resistance ◽  
Ash Content ◽  
Mineral Admixtures ◽  
Binding Agent ◽  
Materials Used ◽  
Plasticizing Admixture

Cement as the binding agent in the production of concrete can be replaced with active mineral admixtures. Biofuel combustion fly ash is one of such admixtures. Materials used for the study: Portland cement CEM I 42.5 R, sand of 0/4 fraction, gravel of 4/16 fraction, biofuel fly ash, superplasticizer, water. Six compositions of concrete were designed by replacing 0%, 5%, 10%, 15% 20%, and 25% of cement with biofuel fly ash. The article analyses the effect of biofuel fly ash content on the properties of concrete. The tests revealed that the increase of biofuel fly ash content up to 20% increases concrete density and compressive strength after 7 and 28 days of curing and decreases water absorption, with corrected water content by using plasticizing admixture. It was found that concrete where 20% of cement is replaced by biofuel ash has higher frost resistance.

Fresh, Durability and Mechanical Behavior of Self Consolidating Concrete Incorporating Fly Ash and Admixture under Hot Weather

2021 ◽  
Vol 904 ◽  
pp. 453-457
Author(s):  
Samer Al Martini ◽  
Reem Sabouni ◽  
Abdel Rahman Magdy El-Sheikh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Weather Conditions ◽  
Chloride Penetration ◽  
The Self ◽  
Fresh Properties ◽  
Self Consolidating Concrete ◽  
Slump Flow ◽  
Hot Weather

The self-consolidating concrete (SCC) become the material of choice by concrete industry due to its superior properties. However, these properties need to be verified under hot weather conditions. The paper investigates the behavior of SCC under hot weather. Six SCC mixtures were prepared under high temperatures. The SCC mixtures incorporated polycarboxylate admixture at different dosages and prolonged mixed for up to 2 hours at 30 °C and 40 °C. The cement paste was replaced with 20% of fly ash (FA). The fresh properties were investigated using slump flow, T50, and VSI tests. The compressive strength was measured at 3, 7, and 28 days. The durability of SCC mixtures was evaluated by conducting rapid chloride penetration and water absorption tests.

Fly ash from Coal-Combustion Waste as an Additive for Quality Improvement and Compressive Strength of Cement

2021 ◽  
Vol 27 (1) ◽  
pp. 127-134
Author(s):  
Roni Adi Wijaya ◽  
Yayuk Astuti ◽  
Septi Wijayanti
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Combustion ◽  
National Standard ◽  
Insoluble Residue ◽  
Chemical Components ◽  
Free Lime ◽  
Mineral Additive ◽  
Additional Mineral

A series of tests were carried out to determine the effect of the addition of coal combustion fly ash as an additional mineral (additive) on improving the quality and compressive strength of cement according to the Indonesian National Standard (SNI 15-2049-2004). Research methods include sample preparation, manufacture of cement with 0%, 5%, 8%, 12%, and 15% fly ash variations, chemical and physical properties of cement. The parameters measured were the level of chemical composition (%) using X-Ray Fluorescence Spectroscopy (XRF) ARL 9800 OASIS, free lime content (%) by volumetry, insoluble residue level (%) by gravimetry, compressive strength (kg/cm2), and smoothness cement (cm2/g). The results showed that the addition of fly ash increased the SiO2 content of cement, thereby increasing C3S and C2S compounds which are compressive strength components of a cement. Besides, the addition of fly ash is directly proportional to IR levels, compressive strength, smoothness, and inversely proportional to free lime levels. So the addition of fly ash can improve the quality of cement by increasing chemical components, increasing compressive strength, and reducing cracking or expansion of cement.

scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

The Effect of Curing Time on the Properties of Fly Ash-Based Geopolymer Bricks

2012 ◽  
Vol 626 ◽  
pp. 937-941 ◽  
Author(s):  
W.I. Wan Mastura ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Mohammed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Experimental Work ◽  
Base Material ◽  
Curing Time ◽  
Curing Conditions ◽  
Alkaline Activator

This paper reports the results of an experimental work conducted to investigate the effect of curing conditions on the properties of fly ash-based geopolymer bricks prepared by using fly ash as base material and combination of sodium hydroxide and sodium silicate as alkaline activator. The experiments were conducted by varying the curing time in the range of 1-24 hours respectively. The specimens cured for a period of 24 hours have presented the highest compressive strength for all ratio of fly ash to sand. For increasing curing time improve compressive strength and decreasing water absorption.

Experimental Study on Sustainable Concrete with the Mixture of Low Calcium Fly Ash and Lime as a Partial Replacement of Cement

2011 ◽  
Vol 250-253 ◽  
pp. 307-312 ◽  
Author(s):  
Muthuramalingam Jayakumar ◽  
M. Salman Abdullahi
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Chloride Ion ◽  
Apparent Volume ◽  
Partial Replacement ◽  
Fly Ash Concrete ◽  
Low Calcium ◽  
Chloride Ion Penetration ◽  
Ion Penetration

Even though the use of fly ash in concrete is nowadays a common practice, its relatively slow pozzolanic reactivity hinders its greater utilization; hence efficient methods of activation are on demand. This study was carried out to evaluate the influence of lime as a chemical activator on the mechanical and durability properties of high strength fly ash concrete. Mixtures were made with 0, 30, 40, and 50% of cement replaced by low calcium fly ash. Corresponding mixtures were also made with the same amount of fly ash and addition of 10% of lime to each mixture. For each concrete mixture, slump, compressive strength, water absorption, sorptivity, apparent volume of permeable voids, and resistance to chloride-ion penetration were measured. The results obtained showed that addition of lime improved the compressive strength significantly at all ages. The strength of all the fly ash mixtures containing lime surpassed that of the corresponding Portland cement mix at 60 days. Addition of lime also improved the sorptivity and resistance to chloride-ion penetration of the fly ash concrete. It however increases the water absorption and the volume of permeable voids of the fly ash concrete.

Sign in / Sign up

Export Citation Format

Share Document