scholarly journals Influence of Fly Ash Additive on the Properties of Concrete with Slag Cement

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3265 ◽  
Author(s):  
Anna Szcześniak ◽  
Jacek Zychowicz ◽  
Adam Stolarski
Keyword(s):  
Fly Ash ◽  
Chloride Ion ◽  
High Strength ◽  
Experimental Tests ◽  
Chloride Ions ◽  
Strength Increase ◽  
Slag Cement ◽  
Initial Strength ◽  
Chloride Ion Penetration ◽  
The Impact

This paper presents research on the impact of fly ash addition on selected physical and mechanical parameters of concrete made with slag cement. Experimental tests were carried out to measure the migration of chloride ions in concrete, the tightness of concrete exposed to water under pressure, and the compressive strength and tensile strength of concrete during splitting. Six series of concrete mixes made with CEM IIIA 42.5 and 32.5 cement were tested. The base concrete mix was modified by adding fly ash as a partial cement substitute in the amounts of 25% and 33%. A comparative analysis of the obtained results indicates a significant improvement in tightness, especially in concrete based on CEM IIIA 32.5 cement and resistance to chloride ion penetration for the concretes containing fly ash additive. In the concretes containing fly ash additive, a slower rate of initial strength increase and high strength over a long period of maturation are shown. In accordance with the presented research results, it is suggested that changes to the European standardization system be considered, to allow the use of fly ash additive in concrete made with CEM IIIA 42.5 or 32.5 cement classes. Such a solution is not currently acceptable in standards in some European Countries.

scholarly journals Damage Mechanism of Mineral Admixture Concrete under Marine Corrosion and Freezing-Thawing Environment

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Yan Li ◽  
Lianying Zhang ◽  
Chao Ma ◽  
Bing Li ◽  
Jiong Zhu
Keyword(s):  
Fly Ash ◽  
Chloride Ion ◽  
Damage Mechanism ◽  
Chloride Ions ◽  
Mineral Admixture ◽  
Ion Concentration ◽  
Dominant Factor ◽  
Marine Corrosion ◽  
Chloride Ion Penetration ◽  
Mineral Powder

Understanding the performance of concrete in the marine environment is significant for preventing the corrosion of chloride ion for marine buildings. In this study, the uniaxial compressive strength (UCS), chloride ion concentration (CIC), microstructure, and pore structure of admixture concretes were tested to study the mechanical properties and microscopic characteristics under the single marine corrosion, the single freezing-thawing, and the coupled marine corrosion and freezing-thawing conditions. The results indicate that the concrete mixed with both fly ash and mineral powder has better UCS, chloride ion penetration resistance, and freezing-thawing resistance than the concrete with the single fly ash or mineral powder. Under the marine corrosion environment and coupled corrosion and freezing-thawing environment, the UCS of the concrete with both fly ash and mineral powder increases firstly and then decreases with the increase of the corrosion time. This is because the pore of the filling body is filled by large crystalline salts generated by the reaction of chloride ions and concrete; then, cementation of the cement is increased in the early corrosion; meanwhile, the increase of crystal salt in the subsequent corrosion process leads to the growth of microcracks and the formation of macrocracks in concrete specimens. In addition, a freezing-thawing-corrosion composite strength impact factor is introduced to describe the effect of coupled corrosion and freezing-thawing on the mechanical property of the concrete. The results show that the corrosion is the dominant factor after 0, 30, and 60 freezing-thawing cycles, while the freezing-thawing is the dominant factor after 90 freezing-thawing cycles.

Effects of Fly Ash and Ground Granulated Blast-Furnaces Slag on Properties of High-Strength Concrete

2009 ◽  
Vol 405-406 ◽  
pp. 219-225 ◽  
Author(s):  
Ji Liang Wang ◽  
Kai Min Niu ◽  
Zhi Feng Yang ◽  
Ming Kai Zhou ◽  
Li Qun Sun ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Chloride Ion ◽  
High Strength ◽  
Volume Stability ◽  
Strength Concrete ◽  
Granulated Blast Furnace Slag ◽  
Chloride Ion Penetration ◽  
Ameliorative Effect

Effects of fly ash and ground granulated blast-furnace slag (GGBFS) on workability, strength, volume stability and durability of HSC are investigated. Results show that fly ash and GGBFS can improve the workability, increase the later strength of high strength concrete (HSC) remarkably, and reduce the brittleness. In addition, the ameliorative effect of GGBFS on HSC brittleness is more remarkable. With the increase of fly ash and GGBFS, the early elastic modulus of HSC reduces. The elastic modulus is similar to the controlled sample when the load is applied after 60d curing. The fly ash and GGBFS can improve HSC’s resistance to chloride ion penetration significantly. However, the effects of fly ash and GGBFS on freezing-hawing resistance of HSC are not obvious. Besides, the fly ash will reduce freezing-hawing resistance of HSC only when the content of mineral powder is up to 36%.

scholarly journals Experimental Investigation on the Effect of Shot Peening and Deep Rolling on the Fatigue Response of High Strength Fasteners

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1093 ◽  
Author(s):  
Reggiani
Keyword(s):  
Fatigue Life ◽  
Shot Peening ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Tests ◽  
Published Data ◽  
Deep Rolling ◽  
Beneficial Impact ◽  
The Impact ◽  
Fatigue Life Enhancement

Shot-peening and deep rolling are mechanical surface treatments that are commonly applied to enhance the fatigue performances of components, owing to their capacity to generate compressive residual stresses and induce work hardening. However, literature is still poor of published data concerning the application of these treatments to high strength steels fasteners, although these represent a class of components among the most widespread. In the present work, the impact of deep rolling and shot-peening performed in the underhead radius of two set of fasteners made of 36NiCrMo and 42CrMoV for fatigue life enhancement has been investigated. The experimental tests consisted of six combinations of shot-peening and deep rolling, including the non-treated state. Two test campaigns have been sequentially carried out with different process parameters and treatment sequences. The results always showed a beneficial impact of the deep rolling on fatigue, especially for the 42CrMoV steel. Conversely, the effect of the shot-peening strongly depended on the selected set of parameters, alternatively leading to an improvement or a worsening of the fatigue life in relation to the level of induced surface roughness.

scholarly journals The Influence of Crystalline Admixtures on the Properties and Microstructure of Mortar Containing By-Products

Buildings ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 146
Author(s):  
Jakub Hodul ◽  
Nikol Žižková ◽  
Ruben Paul Borg
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Chloride Ion ◽  
Capillary Suction ◽  
Chloride Ion Penetration ◽  
Chloride Migration ◽  
Cement Mortars ◽  
Polymer Mortar ◽  
By Products ◽  
Ion Penetration

Crystalline admixtures and industrial by-products can be used in cement-based materials in order to improve their mechanical properties. The research examined long-term curing and the exposure to environmental actions of polymer–cement mortars with crystalline admixture (CA) and different by-products, including Bengħisa fly ash and Globigerina limestone waste filler. The by-products were introduced as a percentage replacement of the cement. A crystallization additive was also added to the mixtures in order to monitor the improvement in durability properties. The mechanical properties of the mortar were assessed, with 20% replacement of cement with fly ash resulting in the highest compressive strength after 540 days. The performance was analyzed with respect to various properties including permeable porosity, capillary suction, rapid chloride ion penetration and chloride migration coefficient. It was noted that the addition of fly ash and crystalline admixture significantly reduced the chloride ion penetration into the structure of the polymer cement mortar, resulting in improved durability. A microstructure investigation was conducted on the samples through Scanning Electron Microscopy-Energy Dispersive X-ray Spectroscopy (SEM-EDS). Crystals forming through the crystalline admixture in the porous structure of the material were clearly observed, contributing to the improved properties of the cement-based polymer mortar.

scholarly journals Effect of Fly Ash as Cement Replacement on Chloride Diffusion, Chloride Binding Capacity, and Micro-Properties of Concrete in a Water Soaking Environment

2020 ◽  
Vol 10 (18) ◽  
pp. 6271 ◽  
Author(s):  
Jun Liu ◽  
Jiaying Liu ◽  
Zhenyu Huang ◽  
Jihua Zhu ◽  
Wei Liu ◽  
...  
Keyword(s):  
Diffusion Coefficient ◽  
Fly Ash ◽  
Binding Capacity ◽  
Chloride Ion ◽  
Chloride Content ◽  
Chloride Ions ◽  
Chloride Diffusion ◽  
Chloride Binding ◽  
Test Results ◽  
New Equation

This paper experimentally studies the effects of fly ash on the diffusion, bonding, and micro-properties of chloride penetration in concrete in a water soaking environment based on the natural diffusion law. Different fly ash replacement ratio of cement in normal concrete was investigated. The effect of fly ash on chloride transportation, diffusion, coefficient, free chloride content, and binding chloride content were quantified, and the concrete porosity and microstructure were also reported through mercury intrusion perimetry and scanning electron microscopy, respectively. It was concluded from the test results that fly ash particles and hydration products (filling and pozzolanic effects) led to the densification of microstructures in concrete. The addition of fly ash greatly reduced the deposition of chloride ions. The chloride ion diffusion coefficient considerably decreased with increasing fly ash replacement, and fly ash benefits the binding of chloride in concrete. Additionally, a new equation is proposed to predict chloride binding capacity based on the test results.

scholarly journals Experimental Tests and Reliability Analysis of the Cracking Impact Resistance of UHPFRC

Fibers ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 74
Author(s):  
Hussain A. Jabir ◽  
Sallal R. Abid ◽  
Gunasekaran Murali ◽  
Sajjad H. Ali ◽  
Sergey Klyuev ◽  
...  
Keyword(s):  
High Performance ◽  
Steel Fiber ◽  
Impact Resistance ◽  
High Strength ◽  
Experimental Tests ◽  
Fiber Reinforced Concrete ◽  
Fiber Types ◽  
Impact Performance ◽  
High Performance Fiber ◽  
The Impact

Ultra-high performance (UHP) concrete is a special type of fibrous cementitious composite that is characterized by high strength and superior ductility, toughness, and durability. This research aimed to investigate the resistance of ultra-high performance fiber-reinforced concrete (UHPFRC) against repeated impacts. An adjusted repeated drop mass impact test was adopted to evaluate the impact performance of 72 UHPFRC disc specimens. The specimens were divided into six mixtures each of 12 discs. The only difference between the mixtures was the types of fibers used, while all other mixture components were the same. Three types of fibers were used: 6 mm micro-steel, 15 mm micro-steel, and polypropylene. All mixtures included 2.5% volumetric content of fibers, however with different combinations of the three fiber types. The test results showed that the mixtures with the 15 mm micro-steel fiber absorbed a higher number of impact blows until cracking compared to other mixtures. The mixture with pure 2.5% of 15 mm micro-steel fiber exhibited the highest impact resistance, with percentage increases over the other mixtures ranging from 25 to 140%. In addition, the Weibull distribution was used to investigate the cracking impact resistance of UHP at different levels of reliability.

Effect of Metakaolin-Based Modifier on the Permeability of Concrete Structure in the Marine Environment

2013 ◽  
Vol 438-439 ◽  
pp. 117-120
Author(s):  
Jun Tao Ma ◽  
Liang Yan ◽  
Yu Ping Tong ◽  
Hui Xian Wang
Keyword(s):  
Fly Ash ◽  
Marine Environment ◽  
Concrete Structure ◽  
Chloride Ion ◽  
Penetration Resistance ◽  
Chloride Ion Penetration ◽  
Working Performance ◽  
Electric Flux ◽  
Penetration Behavior ◽  
Strength And Durability

Corrosion of the steel reinforcement in the concrete structure caused by chloride ion penetration becomes more serious in the marine environment. Metakaolin has been widely used in the concrete structure to improve the strength and durability. The combination of metakaolin (MK) and fine fly ash (FA) was studied in the article and the penetration behavior of concrete with various contents of metakaolin-based modifier is investigated. The penetration resistance of concrete was tested in combination of electric flux test. The improving mechanism was studied with mercury intrusion porosimetry analysis (MIP). The experiment results indicate that metakaolin-based modifier improved the penetration resistance of concrete obviously. The combination of fine fly ash weakened the water sucking action of metakaolin and preserved the working performance of concrete. The pore size distribution of concrete containing metakaolin-based modifier has been optimized to improve the microstructure and enhance the penetration resistance of concrete.

Experimental Study on Sustainable Concrete with the Mixture of Low Calcium Fly Ash and Lime as a Partial Replacement of Cement

2011 ◽  
Vol 250-253 ◽  
pp. 307-312 ◽  
Author(s):  
Muthuramalingam Jayakumar ◽  
M. Salman Abdullahi
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Chloride Ion ◽  
Apparent Volume ◽  
Partial Replacement ◽  
Fly Ash Concrete ◽  
Low Calcium ◽  
Chloride Ion Penetration ◽  
Ion Penetration

Even though the use of fly ash in concrete is nowadays a common practice, its relatively slow pozzolanic reactivity hinders its greater utilization; hence efficient methods of activation are on demand. This study was carried out to evaluate the influence of lime as a chemical activator on the mechanical and durability properties of high strength fly ash concrete. Mixtures were made with 0, 30, 40, and 50% of cement replaced by low calcium fly ash. Corresponding mixtures were also made with the same amount of fly ash and addition of 10% of lime to each mixture. For each concrete mixture, slump, compressive strength, water absorption, sorptivity, apparent volume of permeable voids, and resistance to chloride-ion penetration were measured. The results obtained showed that addition of lime improved the compressive strength significantly at all ages. The strength of all the fly ash mixtures containing lime surpassed that of the corresponding Portland cement mix at 60 days. Addition of lime also improved the sorptivity and resistance to chloride-ion penetration of the fly ash concrete. It however increases the water absorption and the volume of permeable voids of the fly ash concrete.

Sign in / Sign up

Export Citation Format

Share Document