scholarly journals Electrochemical Behavior of Ti6Al4V Alloy Used in Dental Implants Immersed in Streptococcus gordonii and Fusobacterium nucleatum Solutions

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4185
Author(s):  
Myriam A. De la Garza-Ramos ◽  
Francisco H. Estupiñan-Lopez ◽  
Citlalli Gaona-Tiburcio ◽  
Lucía G. Beltrán-Novelo ◽  
Patricia Zambrano-Robledo ◽  
...  
Keyword(s):  
Dental Implants ◽  
Electrochemical Behavior ◽  
Fusobacterium Nucleatum ◽  
Open Circuit ◽  
Ti6al4v Alloy ◽  
Uniform Corrosion ◽  
Streptococcus Gordonii ◽  
Three Solutions ◽  
Ringer’S Lactate ◽  
Titanium Alloy Ti6al4v

The titanium alloy, Ti6Al4V, is used in dentistry for dental implants because of its excellent resistance to corrosion and its high biocompatibility. However, periimplantitis is considered the main reason for treatment failure. The Ti6Al4V alloy was used to study the corrosion behavior for dental implant applications, using an experimental arrangement of three electrodes with the bacteria Streptococcus gordonii and Fusobacterium nucleatum, in addition to Ringer’s lactate as electrolytes, at 37 °C and a pH of 5.6. Their electrochemical behavior was studied by open circuit potential (OCP) and cyclic potentiodynamic polarization (CPP) according to ASTM G3-14 and ASTM G61-11, respectively. Scanning electron microscopy (SEM) was employed to determine the morphology of the alloy studied. An experimental model, in situ, was established with the bacteria present in an oral environment to understand the electrochemical behavior of the alloy used in dental implants. The greatest corrosion in Ti6Al4V alloy was produced by the medium that contained the bacterium Streptococcus gordonii, which is considered a primary colonizer. In addition, the Ti6Al4V alloy presented uniform corrosion in the three solutions at the different exposure times showing a negative hysteresis in CPP.

Laser textured novel patterns on Ti6Al4V alloy for dental implants surface improvement

2021 ◽  
Vol 33 (4) ◽  
pp. 042031
Author(s):  
Gholam Reza Dabbagh ◽  
S. K. Sadrnezhaad ◽  
Reza Shoja Razavi ◽  
Amir Abbas Nourbakhsh ◽  
Nahid Hassanzadeh Nemati
Keyword(s):  
Dental Implants ◽  
Ti6al4v Alloy ◽  
Surface Improvement

scholarly journals Corrosion investigations of Al-Si casting alloys in 0.6 M NaCl solution

2021 ◽  
Vol 41 (3) ◽  
Author(s):  
Sunčana Smokvina Hanza ◽  
Ladislav Vrsalović ◽  
Lovro Štic ◽  
Lovro Liverić
Keyword(s):  
Potentiodynamic Polarization ◽  
Electrochemical Behavior ◽  
Die Casting ◽  
Electrochemical Corrosion ◽  
Microstructural Characterization ◽  
Casting Process ◽  
Corrosion Current ◽  
Optical Microscope ◽  
Open Circuit ◽  
Polarization Measurements

This paper presents results of the corrosion investigations of specimens made from finished parts for the automotive industry, produced by high-pressure die casting and gravity die casting process of six Al-Si alloys (40000 series). Open circuit potential and potentiodynamic polarization measurements have been performed using a potentiostat with three-electrode set-up in 0.6 M NaCl naturally aerated solution. Microstructural characterization before and after electrochemical investigations has been carried out with optical microscope to establish the connection between microstructure and corrosion parameters of investigated alloys and to analyze and record surface changes of each sample due to electrochemical corrosion. All alloys show good corrosion resistance, which manifests with low values of corrosion rates, calculated from the corrosion current densities obtained from potentiodynamic polarization measurements. Differences in electrochemical behavior appear due to the distinctions in their chemical composition and microstructure. The type of casting process does not affect electrochemical behavior of Al-Si alloys.

scholarly journals Electrochemical behavior of AgCu50 in alkaline media in the presence of chlorides and 2-mercaptobenzothiazole

2017 ◽  
Vol 53 (3) ◽  
pp. 349-356 ◽  
Author(s):  
V. Grekulovic ◽  
M. Rajcic-Vujasinovic ◽  
A. Mitovski
Keyword(s):  
Electrochemical Behavior ◽  
Electrode Surface ◽  
Anodic Polarization ◽  
Pure Copper ◽  
Inhibitory Effect ◽  
Open Circuit ◽  
Alkaline Media ◽  
Nacl Solution ◽  
Pure Silver ◽  
Current Densities

Electrochemical behavior of an alloy AgCu50, pure copper, and pure silver, respectively, was investigated by measuring the open circuit potentials using anodic potentiodynamic polarization and potentiostatic method in 0.1 moldm-3 NaOH + 0.02 moldm-3 NaCl solution, without and with adding 2-mercaptobenzothiazole in various concentrations (0.00001 - 0.001 moldm-3). Anodic polarization curves for AgCu50 alloy, showed four current peaks. Potentiostatic curves showed that values of the stationary current densities drop down with the increase of 2-mercaptobenzothiazole concentration in the electrolyte. The electrode surface was analyzed by optical microscopy after the potentiostatic oxidation. Micrographs confirmed that 2-mercaptobenzothiazole has got the inhibitory effect by forming the film of CuMBT and AgMBT which protect the electrode surface from corrosion.

scholarly journals Effect of pH on the Electrochemical Behavior of Hydrogen Peroxide in the Presence of Pseudomonas aeruginosa

2021 ◽  
Vol 9 ◽  
Author(s):  
Javier Espinoza-Vergara ◽  
Paulo Molina ◽  
Mariana Walter ◽  
Miguel Gulppi ◽  
Nelson Vejar ◽  
...  
Keyword(s):  
Hydrogen Peroxide ◽  
Pseudomonas Aeruginosa ◽  
Enzymatic Activity ◽  
Electrochemical Behavior ◽  
Electrochemical Techniques ◽  
Stable State ◽  
Reduction Reaction ◽  
Maximum Activity ◽  
Open Circuit ◽  
Mueller Hinton

The influence of pH on the electrochemical behavior of hydrogen peroxide in the presence of Pseudomonas aeruginosa was investigated using electrochemical techniques. Cyclic and square wave voltammetry were used to monitor the enzymatic activity. A modified cobalt phthalocyanine (CoPc) carbon electrode (OPG), a known catalyst for reducing O2 to H2O2, was used to detect species resulting from the enzyme activity. The electrolyte was a sterilized aqueous medium containing Mueller-Hinton (MH) broth. The open-circuit potential (OCP) of the Pseudomonas aeruginosa culture in MH decreased rapidly with time, reaching a stable state after 4 h. Peculiarities in the E / I response were observed in voltammograms conducted in less than 4 h of exposure to the culture medium. Such particular E/I responses are due to the catalase’s enzymatic action related to the conversion of hydrogen peroxide to oxygen, confirming the authors’ previous findings related to the behavior of other catalase-positive microorganisms. The enzymatic activity exhibits maximum activity at pH 7.5, assessed by the potential at which oxygen is reduced to hydrogen peroxide. At higher or lower pHs, the oxygen reduction reaction (ORR) occurs at higher overpotentials, i.e., at more negative potentials. In addition, and to assess the influence of bacterial adhesion on the electrochemical behavior, measurements of the bacterial-substrate metal interaction were performed at different pH using atomic force microscopy.

Dynamic Action of Mouthwashes Affects the Electrochemical Behavior of Ti6Al4V Alloy

2021 ◽  
Vol 7 (4) ◽  
Author(s):  
Cecília A. Sousa ◽  
Jairo M. Cordeiro ◽  
Allan O. Silva ◽  
Valentim A. R. Barão ◽  
Leonardo P. Faverani ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Ti6al4v Alloy ◽  
Dynamic Action

scholarly journals Constitutive Model and Cutting Simulation of Titanium Alloy Ti6Al4V after Heat Treatment

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4145
Author(s):  
Xiaohua Qian ◽  
Xiongying Duan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
Orthogonal Cutting ◽  
Treatment Method ◽  
Dynamic Mechanical Properties ◽  
Ti6al4v Alloy ◽  
Stress Strain ◽  
Cutting Simulation ◽  
Titanium Alloy Ti6al4v

As a typical high specific strength and corrosion-resistant alloy, titanium alloy Ti6Al4V is widely used in the aviation, ocean, biomedical, sport, and other fields. The heat treatment method is often used to improve the material mechanical properties. To investigate the dynamic mechanical properties of titanium alloy Ti6Al4V after heat treatment, dynamic compressive experiments under high temperature and high strain rate were carried out using split Hopkinson press bar (SHPB) equipment. The stress–strain curves of Ti6Al4V alloy under different temperatures and strain rates were obtained through SHPB compressive tests. The Johnson–Cook (J–C) constitutive equation was used for expressing the stress–strain relationship of titanium alloy under large deformation. In addition, the material constants of the J–C model were fitted based on the experimental data. An orthogonal cutting simulation was performed to investigate the cutting of Ti6Al4V alloy under two different numerical calculation methods based on the established J–C model using the finite element method (FEM). The simulation results confirm that the adiabatic mode is more suitable to analyze the cutting of Ti6Al4V alloy.

scholarly journals Effect of Sterilization on the Properties of a Bioactive Hybrid Coating Containing Hydroxyapatite

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
E. K. K. Baldin ◽  
C. F. Malfatti ◽  
V. Rodói ◽  
R. N. Brandalise
Keyword(s):  
Electrochemical Behavior ◽  
Morphological Changes ◽  
Xrd Analysis ◽  
Dip Coating ◽  
Open Circuit ◽  
Hybrid Coating ◽  
Mechanical Resistance ◽  
X Ray Diffraction ◽  
Wear Performance ◽  
Different Temperatures

The objective of this study was to evaluate the influence of sterilization on a hybrid coating obtained from a sol composed of alkoxysilane tetraethoxysilane (TEOS) and organoalkoxysilane methyltriethoxysilane (MTES) containing 10% (mass) of hydroxyapatite particles. The coating was obtained by dip coating, by applying two layers (protective/bioactive), which were cured at different temperatures (450°C and 60°C). The effects of sterilization on the superficial, electrochemical, bioactive, and mechanical properties of the coating were evaluated by performing different sterilization processes, namely, steam autoclave, hydrogen peroxide plasma, and ethylene oxide. Subsequently, the coating was characterized by using scanning electron microscopy (SEM/FEG), and FTIR measurements were performed to characterize the chemical structure. The bioactivity and degradability of the coating were analyzed by mass variation after immersion in SBF and X-ray diffraction (XRD) analysis. The electrochemical behavior was assessed by open circuit potential (OCP) and potentiodynamic polarization curves and the mechanical behavior by wear resistance. Results showed that all sterilization processes caused significant morphological changes in the hybrid coating. The autoclaved sample presented the highest structural chemical changes, and, consequently, the highest degradability, even though it had a superior bioactive behavior in relation to the other samples. In addition, the sterilization processes influenced the electrochemical behavior of the hybrid coating and altered the mechanical resistance to abrasion, thus presenting lower wear performance in relation to the nonsterilized sample.

scholarly journals In-Situ Monitoring and Analysis of the Pitting Corrosion of Carbon Steel by Acoustic Emission

2019 ◽  
Vol 9 (4) ◽  
pp. 706 ◽  
Author(s):  
Junlei Tang ◽  
Junyang Li ◽  
Hu Wang ◽  
Yingying Wang ◽  
Geng Chen
Keyword(s):  
Acoustic Emission ◽  
Carbon Steel ◽  
Pitting Corrosion ◽  
Optical Microscope ◽  
Open Circuit ◽  
In Situ Monitoring ◽  
Localized Corrosion ◽  
Uniform Corrosion ◽  
Corrosion Morphology

The acoustic emission (AE) technique was applied to monitor the pitting corrosion of carbon steel in NaHCO3 + NaCl solutions. The open circuit potential (OCP) measurement and corrosion morphology in-situ capturing using an optical microscope were conducted during AE monitoring. The corrosion micromorphology was characterized with a scanning electron microscope (SEM). The propagation behavior and AE features of natural pitting on carbon steel were investigated. After completion of the signal processing, including pre-treatment, shape preserving interpolation, and denoising, for raw AE waveforms, three types of AE signals were classified in the correlation diagrams of the new waveform parameters. Finally, a 2D pattern recognition method was established to calculate the similarity of different continuous AE graphics, which is quite effective to distinguish the localized corrosion from uniform corrosion.

Prediction and Measurement of Corrosion Rates of Stainless Steel in Concentrated Sulfuric Acid

CORROSION ◽  
10.5006/0709 ◽  
2013 ◽  
Vol 69 (6) ◽  
pp. 543-550 ◽  
Author(s):  
S. Jones ◽  
K. Coley ◽  
J. Kish
Keyword(s):  
Stainless Steel ◽  
Sulfuric Acid ◽  
Corrosion Behavior ◽  
Electrochemical Behavior ◽  
Open Circuit Potential ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Corrosion Rates ◽  
Transient Nature ◽  
Concentrated Sulfuric Acid

When exposed to concentrated sulfuric acid, stainless steel exhibits unique electrochemical behavior. This behavior can be observed as an oscillation in open-circuit potential between the active and passive states. The transient nature of the corrosion behavior under these conditions results in a distinct challenge for measuring and predicting corrosion rates. Using a series of commercial alloys with various nickel contents, this paper outlines the utilization of electrochemical experimentation to refine the prediction of corrosion rates. The paper also discusses some of the difficulties associated with many traditional electrochemical techniques such as potentiodynamic scans when used for characterizing systems that undergo oscillations in open-circuit potential.

Sign in / Sign up

Export Citation Format

Share Document