scholarly journals Silane-Coating Strategy for Titanium Functionalization Does Not Impair Osteogenesis In Vivo

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1814
Author(s):  
Plinio Mendes Senna ◽  
Carlos Fernando de Almeida Barros Mourão ◽  
Rafael Coutinho Mello-Machado ◽  
Kayvon Javid ◽  
Pietro Montemezzi ◽  
...  
Keyword(s):  
Bone Formation ◽  
Photoelectron Spectroscopy ◽  
Titanium Surface ◽  
Rabbit Model ◽  
Biologically Active ◽  
Force Microscopy ◽  
Atomic Force ◽  
Silane Coating ◽  
Titanium Screws

Silane-coating strategy has been used to bind biological compounds to the titanium surface, thereby making implant devices biologically active. However, it has not been determined if the presence of the silane coating itself is biocompatible to osseointegration. The aim of the present study was to evaluate if silane-coating affects bone formation on titanium using a rabbit model. For this, titanium screw implants (3.75 by 6 mm) were hydroxylated in a solution of H2SO4/30% H2O2 for 4 h before silane-coating with 3-aminopropyltriethoxysilane (APTES). A parallel set of titanium screws underwent only the hydroxylation process to present similar acid-etched topography as a control. The presence of the silane on the surface was checked by x-ray photoelectron spectroscopy (XPS), with scanning electron microscopy (SEM) and atomic force microscopy (AFM). A total of 40 titanium screws were implanted in the tibia of ten New Zealand rabbits in order to evaluate bone-to-implant contact (BIC) after 3 weeks and 6 weeks of healing. Silane-coated surface presented higher nitrogen content in the XPS analysis, while micro- and nano-topography of the surface remained unaffected. No difference between the groups was observed after 3 and 6 weeks of healing (p > 0.05, independent t-test), although an increase in BIC occurred over time. These results indicate that silanization of a titanium surface with APTES did not impair the bone formation, indicating that this can be a reliable tool to anchor osteogenic molecules on the surface of implant devices.

scholarly journals Self-assembled anchor layers/polysaccharide coatings on titanium surfaces: a study of functionalization and stability

2015 ◽  
Vol 6 ◽  
pp. 617-631 ◽  
Author(s):  
Ognen Pop-Georgievski ◽  
Dana Kubies ◽  
Josef Zemek ◽  
Neda Neykova ◽  
Roman Demianchuk ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Covalent Immobilization ◽  
Biologically Active ◽  
Force Microscopy ◽  
Atomic Force ◽  
Infrared Reflection ◽  
Alginate Immobilization ◽  
Titanium Surfaces ◽  
Self Assembled ◽  
The Stability

Composite materials based on a titanium support and a thin, alginate hydrogel could be used in bone tissue engineering as a scaffold material that provides biologically active molecules. The main objective of this contribution is to characterize the activation and the functionalization of titanium surfaces by the covalent immobilization of anchoring layers of self-assembled bisphosphonate neridronate monolayers and polymer films of 3-aminopropyltriethoxysilane and biomimetic poly(dopamine). These were further used to bind a bio-functional alginate coating. The success of the titanium surface activation, anchoring layer formation and alginate immobilization, as well as the stability upon immersion under physiological-like conditions, are demonstrated by different surface sensitive techniques such as spectroscopic ellipsometry, infrared reflection–absorption spectroscopy and X-ray photoelectron spectroscopy. The changes in morphology and the established continuity of the layers are examined by scanning electron microscopy, surface profilometry and atomic force microscopy. The changes in hydrophilicity after each modification step are further examined by contact angle goniometry.

scholarly journals Effect of Fluoride-Modified Titanium Surface on Early Adhesion of Irradiated Osteoblasts

2015 ◽  
Vol 2015 ◽  
pp. 1-9
Author(s):  
Jun Yuan Li ◽  
Li Wu Zheng ◽  
Li Ma ◽  
Dora Lai Wan Kwong ◽  
Lim Kwong Cheung ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Actin Filaments ◽  
Titanium Surface ◽  
Cytokine Production ◽  
Control Surface ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Modified Surface ◽  
Scanning Electron

Objective. The present study aimed to investigate the effect of fluoride-modified titanium surface on adhesion of irradiated osteoblasts.Materials and Methods. Fluoride-modified surface was obtained and the morphology, roughness, and chemical composition of the surface were evaluated by scanning electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy, respectively. The adhesion of irradiated osteoblast-like cells, in terms of number, area, and fluorescence intensity on the titanium surface, was evaluated using immunofluorescence staining.Results. Numerous nanosize pits were seen only in the F-TiO surface. The pits were more remarkable and uniform on F-TiO surface than on TiO surface; however, the amplitude of peaks and bottoms on F-TiO surface appeared to be smaller than on TiO surface. The Sa value and Sdr percentage of TiO surfaces were significantly higher than those of F-TiO surface. The concentrations of main elements such as titanium, oxygen, and carbon were similar on both surfaces. The number of irradiated osteoblasts adhered on the control surface was larger than on fluoride-modified surface. Meanwhile, the cells on the fluoride-modified surface formed more actin filaments.Conclusions. The fluoride-modified titanium surface alters the adhesion of irradiated osteoblasts. Further studies are needed to investigate the proliferation, differentiation, maturation, gene expression, and cytokine production of irradiated osteoblasts on fluoride-modified titanium surface.

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

Rapid, Refined, and Robust Method for Expression, Purification, and Characterization of Recombinant Human Amyloid-beta M1-42

2019 ◽  
Author(s):  
Priya Prakash ◽  
Travis Lantz ◽  
Krupal P. Jethava ◽  
Gaurav Chopra
Keyword(s):  
Amyloid Beta ◽  
Western Blots ◽  
Force Microscopy ◽  
E Coli ◽  
Atomic Force ◽  
Set Up ◽  
Short Time

Amyloid plaques found in the brains of Alzheimer’s disease (AD) patients primarily consists of amyloid beta 1-42 (Ab42). Commercially, Ab42 is synthetized using peptide synthesizers. We describe a robust methodology for expression of recombinant human Ab(M1-42) in Rosetta(DE3)pLysS and BL21(DE3)pLysS competent E. coli with refined and rapid analytical purification techniques. The peptide is isolated and purified from the transformed cells using an optimized set-up for reverse-phase HPLC protocol, using commonly available C18 columns, yielding high amounts of peptide (~15-20 mg per 1 L culture) in a short time. The recombinant Ab(M1-42) forms characteristic aggregates similar to synthetic Ab42 aggregates as verified by western blots and atomic force microscopy to warrant future biological use. Our rapid, refined, and robust technique to purify human Ab(M1-42) can be used to synthesize chemical probes for several downstream in vitro and in vivo assays to facilitate AD research.

scholarly journals Photocatalytic reduction of graphene oxide with cuprous oxide film under UV-vis irradiation

2020 ◽  
Vol 59 (1) ◽  
pp. 207-214 ◽  
Author(s):  
Yao Wang ◽  
Jianqing Feng ◽  
Lihua Jin ◽  
Chengshan Li
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Low Cost ◽  
Photocatalytic Reduction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Reduced Graphene ◽  
Reduction Efficiency ◽  
Metal Organic ◽  
Reduction Effect

AbstractWe have grown Cu2O films by different routes including self-oxidation and metal-organic deposition (MOD). The reduction efficiency of Cu2O films on graphene oxide (GO) synthesized by modified Hummer’s method has been studied. Surface morphology and chemical state of as-prepared Cu2O film and GO sheets reduced at different conditions have also been investigated using atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS). Results show that self-oxidation Cu2O film is more effective on phtocatalytic reduction of GO than MOD-Cu2O film. Moreover, reduction effect of self-oxidation Cu2O film to GO is comparable to that of environmental-friendly reducing agent of vitamin C. The present results offer a potentially eco-friendly and low-cost approach for the manufacture of reduced graphene oxide (RGO) by photocatalytic reduction.

scholarly journals Biomechanics of Neutrophil Tethers

Life ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 515
Author(s):  
Andrea Cugno ◽  
Alex Marki ◽  
Klaus Ley
Keyword(s):  
Cell Activation ◽  
Optical Trap ◽  
Biomechanical Properties ◽  
Force Microscopy ◽  
Advantages And Disadvantages ◽  
Atomic Force ◽  
Microfluidic Flow ◽  
Biomembrane Force Probe ◽  
Membrane Reservoir

Leukocytes, including neutrophils, which are propelled by blood flow, can roll on inflamed endothelium using transient bonds between selectins and their ligands, and integrins and their ligands. When such receptor–ligand bonds last long enough, the leukocyte microvilli become extended and eventually form thin, 20 m long tethers. Tether formation can be observed in blood vessels in vivo and in microfluidic flow chambers. Tethers can also be extracted using micropipette aspiration, biomembrane force probe, optical trap, or atomic force microscopy approaches. Here, we review the biomechanical properties of leukocyte tethers as gleaned from such measurements and discuss the advantages and disadvantages of each approach. We also review and discuss viscoelastic models that describe the dependence of tether formation on time, force, rate of loading, and cell activation. We close by emphasizing the need to combine experimental observations with quantitative models and computer simulations to understand how tether formation is affected by membrane tension, membrane reservoir, and interactions of the membrane with the cytoskeleton.

scholarly journals Interface Structures and Electronic States of Epitaxial Tetraazanaphthacene on Single-Crystal Pentacene

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1088
Author(s):  
Yuki Gunjo ◽  
Hajime Kamebuchi ◽  
Ryohei Tsuruta ◽  
Masaki Iwashita ◽  
Kana Takahashi ◽  
...  
Keyword(s):  
Single Crystal ◽  
Photoelectron Spectroscopy ◽  
Grazing Incidence ◽  
Force Microscopy ◽  
Interface Dipole ◽  
Atomic Force ◽  
Interfacial Structures ◽  
Donor And Acceptor ◽  
A Charge ◽  
Interface Structures

The structural and electronic properties of interfaces composed of donor and acceptor molecules play important roles in the development of organic opto-electronic devices. Epitaxial growth of organic semiconductor molecules offers a possibility to control the interfacial structures and to explore precise properties at the intermolecular contacts. 5,6,11,12-tetraazanaphthacene (TANC) is an acceptor molecule with a molecular structure similar to that of pentacene, a representative donor material, and thus, good compatibility with pentacene is expected. In this study, the physicochemical properties of the molecular interface between TANC and pentacene single crystal (PnSC) substrates were analyzed by atomic force microscopy, grazing-incidence X-ray diffraction (GIXD), and photoelectron spectroscopy. GIXD revealed that TANC molecules assemble into epitaxial overlayers of the (010) oriented crystallites by aligning an axis where the side edges of the molecules face each other along the [1¯10] direction of the PnSC. No apparent interface dipole was found, and the energy level offset between the highest occupied molecular orbitals of TANC and the PnSC was determined to be 1.75 eV, which led to a charge transfer gap width of 0.7 eV at the interface.

Preparation and Characterization of Chitosan-Casein Phosphopeptides Biocomposite Coatings on the Medical Titanium Alloy

2011 ◽  
Vol 480-481 ◽  
pp. 1065-1069
Author(s):  
Bin Liu ◽  
Lin Wang ◽  
Yin Zhong Bu ◽  
Sheng Rong Yang ◽  
Jin Qing Wang
Keyword(s):  
Photoelectron Spectroscopy ◽  
Attenuated Total Reflectance ◽  
Ti Alloy ◽  
Force Microscopy ◽  
Implant Materials ◽  
Atomic Force ◽  
Casein Phosphopeptides ◽  
Potential Applications ◽  
First Time

Titanium (Ti) and its alloys have been applied in orthopedics as one of the most popular biomedical metallic implant materials. In this work, to enhance the bioactivity, the surface of Ti alloy pre-modified by silane coupling agent and glutaraldehyde was covalently grafted with chitosan (CS) via biochemical multistep self-assembled method. Then, for the first time, the achieved surface was further immobilized with casein phosphopeptides (CPP), which are one group of bioactive peptides released from caseins in the digestive tract and can facilitate the calcium adsorption and usage, to form CS-CPP biocomposite coatings. The structure and composition of the fabricated coatings were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and atomic force microscopy (AFM). As the experimental results indicated, multi-step assembly was successfully performed, and the CS and CPP were assembled onto the Ti alloy surface orderly. It is anticipated that the Ti alloys modified by CS-CPP biocomposite coatings will find potential applications as implant materials in biomedical fields.

Curcumin delivery by modified biosourced carbon-based nanoparticles

Nanomedicine ◽  
2022 ◽  
Author(s):  
Hossein Danafar ◽  
Marziyeh Salehiabar ◽  
Murat Barsbay ◽  
Hossein Rahimi ◽  
Mohammadreza Ghaffarlou ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Free System ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Good Biocompatibility ◽  
Drug Free ◽  
Mcf 7 ◽  
Carbon Based

Aim: To prepare a novel hybrid system for the controlled release and delivery of curcumin (CUR). Methods: A method for the ultrasound-assisted fabrication of protein-modified nanosized graphene oxide-like carbon-based nanoparticles (CBNPs) was developed. After being modified with bovine serum albumin (BSA), CUR was loaded onto the synthesized hybrid (labeled CBNPs@BSA–CUR). The structure and properties of the synthesized nanoparticles were elucidated using transmission electron microscopy (TEM), atomic force microscopy (AFM), ultraviolet-visible spectroscopy (UV-Vis), Fourier-transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy (XPS) methods. Results: CBNPs@BSA–CUR showed pH sensitivity and were calculated as controlled CUR release behavior. The drug-free system exhibited good biocompatibility and was nontoxic. However, CBNPs@BSA–CUR showed acceptable antiproliferative ability against MCF-7 breast cancer cells. Conclusion: CBNPs@BSA–CUR could be considered a highly promising nontoxic nanocarrier for the delivery of CUR with good biosafety.

Sign in / Sign up

Export Citation Format

Share Document