scholarly journals Effect of Strain Rate on the Transverse Tension and Compression Behavior of a Unidirectional Non-Crimp Fabric Carbon Fiber/Snap-Cure Epoxy Composite

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7314
Author(s):  
Khizar Rouf ◽  
Aaditya Suratkar ◽  
Jose Imbert-Boyd ◽  
Jeffrey Wood ◽  
Michael Worswick ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fracture Surface ◽  
Strain Rate ◽  
Epoxy Composite ◽  
Strain Rates ◽  
Transverse Compression ◽  
Compression Tests ◽  
Rate Dependent ◽  
Transverse Tension ◽  
Tension And Compression

The strain rate-dependent behavior of a unidirectional non-crimp fabric (UD-NCF) carbon fiber/snap-cure epoxy composite loaded along the transverse direction under quasi-static and dynamic conditions was characterized. Transverse tension and compression tests at quasi-static and intermediate strain rates were performed using hydraulic testing machines, while a split Hopkinson pressure bar (SHPB) apparatus was used for transverse compression tests at high strain rates. A pulse shaper was used on the SHPB apparatus to ensure dynamic equilibrium was achieved and that the test specimens deformed homogenously with a nearly constant strain rate. The transverse tensile strength at a strain rate of 16 s−1 increased by 16% when compared to that at quasi-static strain rates, while distinct localized fracture surface morphology was observed for specimens tested at different strain rates. The transverse compressive yield stress and strength at a strain rate of 325 s−1 increased by 94% and 96%, respectively, when compared to those at quasi-static strain rates. The initial fracture plane orientation for the transverse compression tests was captured with high-speed cameras and found to increase with increasing strain rate. The study provides an important data set for the strain rate-dependent response of a UD-NCF composite material, while the qualitative fracture surface observations provide a deeper understanding of the failure characteristics.

Strain Rate Effect on Dynamic Compressive Failures in Off-Axis Glass-Epoxy Composites

2000 ◽  
Author(s):  
Jialin Tsai ◽  
C. T. Sun
Keyword(s):  
Shear Modulus ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Rate Dependent ◽  
Bifurcation Buckling ◽  
Split Hopkinson ◽  
Pressure Bar

Abstract Dynamic compressive strength of off-axis S2/8552 glass-epoxy composite in the form of fiber microbuckling was studied. Based on the bifurcation buckling analysis, the microbuckling stress is approximately equal to the composite tangent shear modulus. Using a viscoplastic constitutive model to describe the composite tangent shear modulus, microbuckling stresses at various strain rates were predicted. Small angle off-axis composite specimens were tested to failure at various strain rates. For strain rates below 1/sec, the compression tests were conducted on an MTS machine, while higher strain rate tests were carried out using a Split Hopkinson Pressure Bar (SHPB). Fiber microbuckling was found to be the dominant failure mode for 5°, 10° and 15° specimens within the range of tested strain rates. Comparison of model prediction with experimental data shows that the rate-dependent microbuckling model can be used for predicting compressive strengths at strain rates up to 1100/s.

High Strain Rate Tensile and Compressive Testing of Braided Composite Materials

2004 ◽  
Vol 1-2 ◽  
pp. 217-224 ◽  
Author(s):  
Nick Warrior ◽  
R. Fernie
Keyword(s):  
Composite Materials ◽  
Strain Rate ◽  
Vinyl Ester ◽  
Compressive Loading ◽  
Strain Rates ◽  
Compression Tests ◽  
Rate Dependency ◽  
Unit Cell Size ◽  
Tension And Compression ◽  
Falling Weight

Data from tension and compression tests at quasi-static and impact strain rates of up to 50s −1 (corresponding to impact speeds of up to 7ms −1) are presented to characterise the effect of strain rate on mechanical properties of triaxially braided carbon/vinyl ester. Three braid architectures were studied; 0°/±30°, 0°/±45° and 0°/±60° where the 0° was an 80k tow and the ±30° to ±60° braid tow was 12k. The methodologies and apparatus used were developed for testing composite materials with a large unit cell size at a range of strain rates and are based on novel tensile and compressive loading rigs in conjunction with a modified instrumented falling weight machine (drop tower). In the paper, the effects of increase in strain rate on fibre and matrix dominated material properties are presented. The ultimate tensile and compressive strengths were found to vary with rate. The axial properties of the braided carbon/vinyl ester, dominated by the 80K carbon fibre tow, were relatively insensitive to rate, but strong rate dependency was seen in the transverse directions where the effects of the polymer resin were more significant.

A Newly Developed Clamping Device for the Tension/Compression Test at Various Strain Rates

2014 ◽  
Vol 626 ◽  
pp. 353-358
Author(s):  
Geun Su Joo ◽  
Min Kuk Choi ◽  
Hoon Huh
Keyword(s):  
Strain Rate ◽  
Sheet Metal ◽  
Metal Forming ◽  
Loading Condition ◽  
Strain Rates ◽  
Compression Tests ◽  
Compression Behavior ◽  
Compression Loading ◽  
Hardening Behavior ◽  
Clamping Device

The tension/compression hardening behavior is important in sheet metal forming processes because of complicated loading paths. Experimental methods to measure the tension/ compression behavior have not considered the effect of the strain rate although the strain rate is related to the hardening behavior of sheet metal. The tension/compression tests need to be conducted considering the strain rate to acquire accurate hardening behavior.This paper deals with an experimental technique to measure the tension/compression behavior of sheet metal at various strain rates. A new clamping device was developed to prevent a sheet specimen from buckling under compression loading condition. Compared to previous clamping devices, the clamping device was devised to uniformly impose a clamping force and easily measure the strain from side of a specimen. Tension/compression tests have been conducted at various strain rates for SPCC and DP590 with displacement of 10%. Hardening curves under the tension or compression loading condition were obtained and analyzed with respect to the strain rate.

scholarly journals Hot Deformation Behavior of a Ni-Based Superalloy with Suppressed Precipitation

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 605
Author(s):  
Franco Lizzi ◽  
Kashyap Pradeep ◽  
Aleksandar Stanojevic ◽  
Silvana Sommadossi ◽  
Maria Cecilia Poletti
Keyword(s):  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Hot Deformation ◽  
Strain Rates ◽  
Compression Tests ◽  
Deformation Bands ◽  
Stress Softening ◽  
Relative Stress ◽  
The Matrix ◽  
Thermomechanical Processes

Inconel®718 is a well-known nickel-based super-alloy used for high-temperature applications after thermomechanical processes followed by heat treatments. This work describes the evolution of the microstructure and the stresses during hot deformation of a prototype alloy named IN718WP produced by powder metallurgy with similar chemical composition to the matrix of Inconel®718. Compression tests were performed by the thermomechanical simulator Gleeble®3800 in a temperature range from 900 to 1025 °C, and strain rates scaled from 0.001 to 10 s−1. Flow curves of IN718WP showed similar features to those of Inconel®718. The relative stress softening of the IN718WP was comparable to standard alloy Inconel®718 for the highest strain rates. Large stress softening at low strain rates may be related to two phenomena: the fast recrystallization rate, and the coarsening of micropores driven by diffusion. Dynamic recrystallization grade and grain size were quantified using metallography. The recrystallization grade increased as the strain rate decreased, although showed less dependency on the temperature. Dynamic recrystallization occurred after the formation of deformation bands at strain rates above 0.1 s−1 and after the formation of subgrains when deforming at low strain rates. Recrystallized grains had a large number of sigma 3 boundaries, and their percentage increased with strain rate and temperature. The calculated apparent activation energy and strain rate exponent value were similar to those found for Inconel®718 when deforming above the solvus temperature.

Influence of strain rate, temperature and fatigue on the radial compression behaviour of Norway spruce

Holzforschung ◽  
2017 ◽  
Vol 71 (6) ◽  
pp. 505-514 ◽  
Author(s):  
Carolina Moilanen ◽  
Tomas Björkqvist ◽  
Markus Ovaska ◽  
Juha Koivisto ◽  
Amandine Miksic ◽  
...  
Keyword(s):  
Strain Rate ◽  
Linear Model ◽  
Norway Spruce ◽  
Material Model ◽  
Radial Compression ◽  
Compression Tests ◽  
Static Compression ◽  
Rate Dependent ◽  
Compression Model ◽  
Wood Compression

Abstract A dynamic elastoplastic compression model of Norway spruce for virtual computer optimization of mechanical pulping processes was developed. The empirical wood behaviour was fitted to a Voigt-Kelvin material model, which is based on quasi static compression and high strain rate compression tests (QSCT and HSRT, respectively) of wood at room temperature and at high temperature (80–100°C). The effect of wood fatigue was also included in the model. Wood compression stress-strain curves have an initial linear elastic region, a plateau region and a densification region. The latter was not reached in the HSRT. Earlywood (EW) and latewood (LW) contributions were considered separately. In the radial direction, the wood structure is layered and can well be modelled by serially loaded layers. The EW model was a two part linear model and the LW was modelled by a linear model, both with a strain rate dependent term. The model corresponds well to the measured values and this is the first compression model for EW and LW that is based on experiments under conditions close to those used in mechanical pulping.

scholarly journals A Strain Rate-Dependent Damage Evolution Model for Concrete Based on Experimental Results

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Bin Xu ◽  
Xiaoyan Lei ◽  
P. Wang ◽  
Hui Song
Keyword(s):  
Strain Rate ◽  
Uniaxial Compression ◽  
Damage Evolution ◽  
Damage Model ◽  
Evolution Model ◽  
Experimental Results ◽  
Strain Rates ◽  
Compression Tests ◽  
Stress Strain ◽  
Actual Damage

There are various definitions of damage variables from the existing damage models. The calculated damage value by the current methods still could not well correspond to the actual damage value. Therefore, it is necessary to establish a damage evolution model corresponding to the actual damage evolution. In this paper, a strain rate-sensitive isotropic damage model for plain concrete is proposed to describe its nonlinear behavior. Cyclic uniaxial compression tests were conducted on concrete samples at three strain rates of 10−3s−1, 10−4s−1, and 10−5s−1, respectively, and ultrasonic wave measurements were made at specified strain values during the loading progress. A damage variable was defined using the secant and initial moduli, and concrete damage evolution was then studied using the experimental results of the cyclic uniaxial compression tests conducted at the different strain rates. A viscoelastic stress-strain relationship, which considered the proposed damage evolution model, was presented according to the principles of irreversible thermodynamics. The model results agreed well with the experiment and indicated that the proposed damage evolution model can accurately characterize the development of macroscopic mechanical weakening of concrete. A damage-coupled viscoelastic constitutive relationship of concrete was recommended. It was concluded that the model could not only characterize the stress-strain response of materials under one-dimensional compressive load but also truly reflect the degradation law of the macromechanical properties of materials. The proposed damage model will advance the understanding of the failure process of concrete materials.

scholarly journals Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect

2020 ◽  
Author(s):  
Chuang Liu ◽  
Dongzhi Sun ◽  
Xianfeng Zhang ◽  
Florence Andrieux ◽  
Tobias Gerster
Keyword(s):  
Cast Iron ◽  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Damage Model ◽  
Iron Alloys ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Damage Models ◽  
Rate Dependent

Abstract Cast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic tensile tests at strain rates of 10− 4, 1, 10, 100, and 250 s− 1 were carried out. In order to investigate the effects of stress state, specimens with various geometries were used in the experiments. Stress–strain curves and fracture strains of the GJS-450 alloy in the strain-rate range of 10− 4 to 250 s− 1 were obtained. A strain rate-dependent plastic flow law based on the Voce model is proposed to describe the mechanical behavior in the corresponding strain-rate range. The deformation behavior at various strain rates is observed and analyzed through simulations with the proposed strain rate-dependent constitutive model. The available damage model from Bai and Wierzbicki is extended to take the strain rate into account and calibrated based on the analysis of local fracture strains. The validity of the proposed constitutive model including the damage model was verified by the corresponding experimental results. The results show that the strain rate has obviously nonlinear effects on the yield stress and fracture strain of GJS-450 alloys. The predictions with the proposed constitutive model and damage models at various strain rates agree well with the experimental results, which illustrates that the rate-dependent flow rule and damage models can be used to describe the mechanical behavior of cast iron alloys at elevated strain rates.

Hot working of SP-700 titanium alloy with lamellar α + β starting structure using a processing map

2020 ◽  
Vol 111 (4) ◽  
pp. 297-306
Author(s):  
Amir Hosein Sheikhali ◽  
Maryam Morakkabati
Keyword(s):  
Titanium Alloy ◽  
Strain Rate ◽  
Hot Deformation ◽  
Processing Map ◽  
Microstructural Analysis ◽  
Shear Bands ◽  
Alpha Phase ◽  
Strain Rates ◽  
Compression Tests ◽  
Temperature Range

Abstract In this study, hot deformation behavior of SP-700 titanium alloy was investigated by hot compression tests in the temperature range of 700-9508C and at strain rates of 0.001, 0.1, and 1 s-1. Final mechanical properties of the alloy (hot compressed at different strain rates and temperatures) were investigated using a shear punch testing method at room temperature. The flow curves of the alloy indicated that the yield point phenomenon occurs in the temperature range of 800- 9508C and strain rates of 0.1 and 1 s-1. The microstructural analysis showed that dynamic globularization of the lamellar α phase starts at 7008C and completes at 8008C. The alpha phase was completely eliminated from b matrix due to deformation- induced transformation at 8508C. The microstructure of specimens compressed at 8508C and strain rates of 0.001 and 0.1 s-1showed the serration of beta grain boundaries, whereas partial dynamic recrystallization caused a necklace structure by increasing strain rate up to 1 s-1. The specimen deformed at 7008C and strain rate of 1 s-1was located in the instability region and localized shear bands formed due to the low thermal conductivity of the alloy. The processing map of the alloy exhibited a peak efficiency domain of 54% in the temperature range of 780-8108C and strain rates of 0.001- 0.008 s-1. The hot deformation activation energy of the alloy in the α/β region (305.5 kJ mol-1) was higher than that in the single-phase β region (165.2 kJ mol-1) due to the dynamic globularization of the lamellar a phase.

STRAIN RATE-DEPENDENT CHARACTERIZATION OF THE IN-PLANE SHEAR RESPONSE OF A UNIDIRECTIONAL NON-CRIMP FABRIC CARBON FIBER/SNAP-CURE EPOXY COMPOSITE

2021 ◽  
Author(s):  
KHIZAR ROUF ◽  
MICHAEL J. WORSWICK ◽  
JOHN MONTESANO
Keyword(s):  
Carbon Fiber ◽  
Strain Rate ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Equilibrium ◽  
Epoxy Composite ◽  
Axial Strain ◽  
Image Correlation ◽  
High Rate ◽  
Plane Shear

The dynamic in-plane shear stress-strain response of a unidirectional non- crimp fabric carbon fiber/snap-cure epoxy composite was studied by subjecting 30° and 45° off-axis specimens to compression loading at high strain rates. Tests were performed using a compression split-Hopkinson pressure bar apparatus where an approximate axial strain rate of 305 s-1 was achieved. Images of the deformed specimen surfaces were captured with high-speed cameras and digital image correlation used to obtain a strain map. Pulse shaping was performed using a copper pulse shaper to achieve dynamic equilibrium during the high-rate tests. The results demonstrated that the in-plane shear yield stress and strength increased by 53% and 68%, respectively, when the strain rate increased from quasi-static to 305 s-1.

scholarly journals Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 344 ◽  
Author(s):  
Simon Sevsek ◽  
Christian Haase ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Manganese Steel ◽  
Strain Rates ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Multi Phase

The strain-rate-dependent deformation behavior of an intercritically annealed X6MnAl12-3 medium-manganese steel was analyzed with respect to the mechanical properties, activation of deformation-induced martensitic phase transformation, and strain localization behavior. Intercritical annealing at 675 °C for 2 h led to an ultrafine-grained multi-phase microstructure with 45% of mostly equiaxed, recrystallized austenite and 55% ferrite or recovered, lamellar martensite. In-situ digital image correlation methods during tensile tests revealed strain localization behavior during the discontinuous elastic-plastic transition, which was due to the localization of strain in the softer austenite in the early stages of plastic deformation. The dependence of the macroscopic mechanical properties on the strain rate is due to the strain-rate sensitivity of the microscopic deformation behavior. On the one hand, the deformation-induced phase transformation of austenite to martensite showed a clear strain-rate dependency and was partially suppressed at very low and very high strain rates. On the other hand, the strain-rate-dependent relative strength of ferrite and martensite compared to austenite influenced the strain partitioning during plastic deformation, and subsequently, the work-hardening rate. As a result, the tested X6MnAl12-3 medium-manganese steel showed a negative strain-rate sensitivity at very low to medium strain rates and a positive strain-rate sensitivity at medium to high strain rates.

Sign in / Sign up

Export Citation Format

Share Document