Ornamental Stone Cutting Processing and Sludge Production Evaluation with the Goal of Ending Waste

2021 ◽  
Vol 5 (1) ◽  
pp. 57
Author(s):  
Lorena Zichella ◽  
Rossana Bellopede ◽  
Paola Marini

In the quarry sector, the reduction of landfill material may be obtained not only by finding a suitable recovery of the material as a by-product, but also by identifying the best available cutting technique to be used on the basis of the physical, chemical, and mechanical characteristics of the stones. The choice of the best cutting technique could lead to high efficiency and performance, high quality of the cut surfaces, and a very low environmental impact by reducing energy consumption, decreasing the concentration of heavy metals in the sludge, and producing less waste. In this context, an analysis of the procedures for cutting different types of ornamental stones into slabs together with the evaluation of sludge production for the different cutting methods has been carried out. Two types of analysis were carried out in parallel: evaluation of the stones workability and calculation of the amount of sludge produced in the three different cutting technologies and from the cutting of blocks. A comparison was carried out on the quality of the sludge produced, on type and quantity of metals present, taking into account the different cutting technologies. The performed tests were: chemical analysis, magnetic separation test, and SEM analysis of the metal fraction. The study could provide stone producers with a technological, scientific instrument to identify the best cutting techniques for the processing of their stones, in order to obtain a high-efficiency process, optimize the recovery process, increase the economic advantages, and evaluate the possible reuse of the sludge through a proactive waste management strategy.

2020 ◽  
Author(s):  
Lorena Zichella ◽  
Rossana Bellopede ◽  
Paola Marini

<p>The End-of-waste concept was introduced by the ‘Thematic Strategy on the prevention and recycling of waste’ adopted by the European Commission, in which it proposed to specify the conditions for the cessation of waste status as part of the revision of the Waste Framework Directive (Directive 2008/98/EC). The Directive states that a waste shall lose its status if it is submitted to a recovery operation (including recycling) and comply with specific eligibility criteria. The strategic goal of the End-of-waste is to promote recycling, helping to ensure a high level of environmental protection through the reduction of the consumption of critical raw materials and the quantities of waste destined for disposal.</p><p>In the mining sector, the reduction of landfill material may be obtained not only by finding a suitable recovery of the material as a by-product, but also identifying the best available cutting technique to be used on the basis of the physical, chemical and mechanical characteristics of the stones. The choice of the best cutting technique could lead to high efficiency and performance, high quality of the cut surfaces and a very low environmental impact by reducing energy consumption, decreasing the concentration of heavy metals in the sludge and producing less waste.</p><p>In this context, an analysis of the procedures for cutting different types of ornamental stones into slabs together with the evaluation of sludge production for the different cutting methods has been carried out.</p><p>Three types of analysis were conducted in parallel. The first concerns the characterization of the stones and the choice of the type of cutting machine. The analyses carried out were: petrographic analysis, compression strength, flexural strength, apparent density and water absorption. Also ultrasonic pulse velocity (UPV) and Knoop analyses were performed in order to establish the workability class of the stones, and their classification in accordance with previous research works (EASE R3).</p><p>The second analysis involves calculating the amount of sludge produced in the three different cutting technologies, taking into account the same block characteristics. The third analysis was conducted on the sludge resulting from the processing of blocks cut into slabs. A comparison was carried out on the quality of the sludge produced, or type and quantity of metals present, taking into account the three different technologies. The tests carried out were: chemical analysis, magnetic separation test and SEM analysis of the metal fraction.</p><p>The study could provide stone producers with a technological, scientific instrument to identify the best cutting techniques for the processing of their stones, in order to obtain a good efficiency process, optimize the recovery process, increase the economic advantages, and evaluate the possible reuse of the sludge through a proactive waste management strategy.</p>


2019 ◽  
Vol 1 (1) ◽  
pp. 92
Author(s):  
Fazidah Hanim Husain

Lighting is one of the key elements in any space and building infrastructure. Good design for an area in the building requires sufficient light that contributes to the efficiency of the activities. The correct method allows natural light to transmit, reduce heat and glare in providing a conducive learning environment. Light plays a significant influence to the quality of space and contributes focus of the students in an architecture studio. Previous research has shown that the effect of light also controlled emotions, behavior, and mood of the students. The operations of artificial lighting that have been used most of the time in an architecture studio during day and night may create lavishness and inadequacy at the same time. Therefore, this paper focuses on the identifying the quality of light for the architecture studio in UiTM (Perak), to instill a creative learning environment. Several methodologies adopted in this study such as illuminance level measurement using lux meter (LM-8100), and a questionnaire survey in gauging the lighting comfort level from students’ perspective. The study revealed that the illuminance level in the architecture studio is insufficient and not in the acceptable range stated in the Malaysian: Standards 1525:2007 and  not evenly distributed.  The study also concluded that the current studio environment is not condusive and appears monotonous. 


2020 ◽  
Vol 16 (4) ◽  
pp. 730-744
Author(s):  
V.I. Loktionov

Subject. The article reviews the way strategic threats to energy security influence the quality of people's life. Objectives. The study unfolds the theory of analyzing strategic threats to energy security by covering the matter of quality of people's life. Methods. To analyze the way strategic threats to energy security spread across cross-sectoral commodity and production chains and influences quality of people's living, I applied the factor analysis and general scientific methods of analysis and synthesis. Results. I suggest interpreting strategic threats to energy security as risks of people's quality of life due to a reduction in the volume of energy supply. I identified mechanisms reflecting how the fuel and energy complex and its development influence the quality of people's life. The article sets out the method to assess such quality-of-life risks arising from strategic threats to energy security. Conclusions and Relevance. In the current geopolitical situation, strategic threats to energy security cause long-standing adverse consequences for the quality of people's life. If strategic threats to energy security are further construed as risk of quality of people's life, this will facilitate the preparation and performance of a more effective governmental policy on energy, which will subsequently raise the economic well-being of people.


2015 ◽  
Vol 6 (1) ◽  
pp. 50-57
Author(s):  
Rizqa Raaiqa Bintana ◽  
Putri Aisyiyah Rakhma Devi ◽  
Umi Laili Yuhana

The quality of the software can be measured by its return on investment. Factors which may affect the return on investment (ROI) is the tangible factors (such as the cost) dan intangible factors (such as the impact of software to the users or stakeholder). The factor of the software itself are assessed through reviewing, testing, process audit, and performance of software. This paper discusses the consideration of return on investment (ROI) assessment criteria derived from the software and its users. These criteria indicate that the approach may support a rational consideration of all relevant criteria when evaluating software, and shows examples of actual return on investment models. Conducted an analysis of the assessment criteria that affect the return on investment if these criteria have a disproportionate effort that resulted in a return on investment of a software decreased. Index Terms - Assessment criteria, Quality assurance, Return on Investment, Software product


Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1117
Author(s):  
Bin Li ◽  
Zhikang Jiang ◽  
Jie Chen

Computing the sparse fast Fourier transform (sFFT) has emerged as a critical topic for a long time because of its high efficiency and wide practicability. More than twenty different sFFT algorithms compute discrete Fourier transform (DFT) by their unique methods so far. In order to use them properly, the urgent topic of great concern is how to analyze and evaluate the performance of these algorithms in theory and practice. This paper mainly discusses the technology and performance of sFFT algorithms using the aliasing filter. In the first part, the paper introduces the three frameworks: the one-shot framework based on the compressed sensing (CS) solver, the peeling framework based on the bipartite graph and the iterative framework based on the binary tree search. Then, we obtain the conclusion of the performance of six corresponding algorithms: the sFFT-DT1.0, sFFT-DT2.0, sFFT-DT3.0, FFAST, R-FFAST, and DSFFT algorithms in theory. In the second part, we make two categories of experiments for computing the signals of different SNRs, different lengths, and different sparsities by a standard testing platform and record the run time, the percentage of the signal sampled, and the L0, L1, and L2 errors both in the exactly sparse case and the general sparse case. The results of these performance analyses are our guide to optimize these algorithms and use them selectively.


Author(s):  
Jie Gao ◽  
Chunde Tao ◽  
Dongchen Huo ◽  
Guojie Wang

Marine, industrial, turboprop and turboshaft gas turbine engines use nonaxisymmetric exhaust volutes for flow diffusion and pressure recovery. These processes result in a three-dimensional complex turbulent flow in the exhaust volute. The flows in the axial turbine and nonaxisymmetric exhaust volute are closely coupled and inherently unsteady, and they have a great influence on the turbine and exhaust aerodynamic characteristics. Therefore, it is very necessary to carry out research on coupled axial turbine and nonaxisymmetric exhaust volute aerodynamics, so as to provide reference for the high-efficiency turbine-volute designs. This paper summarizes and analyzes the recent advances in the field of coupled axial turbine and nonaxisymmetric exhaust volute aerodynamics for turbomachinery. This review covers the following topics that are important for turbine and volute coupled designs: (1) flow and loss characteristics of nonaxisymmetric exhaust volutes, (2) flow interactions between axial turbine and nonaxisymmetric exhaust volute, (3) improvement of turbine and volute performance within spatial limitations and (4) research methods of coupled turbine and exhaust volute aerodynamics. The emphasis is placed on the turbine-volute interactions and performance improvement. We also present our own insights regarding the current research trends and the prospects for future developments.


Author(s):  
Muhsin Aljuboury ◽  
Md Jahir Rizvi ◽  
Stephen Grove ◽  
Richard Cullen

The goal of this experimental study is to manufacture a bolted GFRP flange connection for composite pipes with high strength and performance. A mould was designed and manufactured, which ensures the quality of the composite materials and controls its surface grade. Based on the ASME Boiler and Pressure Vessel Code, Section X, this GFRP flange was fabricated using biaxial glass fibre braid and polyester resin in a vacuum infusion process. In addition, many experiments were carried out using another mould made of glass to solve process-related issues. Moreover, an investigation was conducted to compare the drilling of the GFRP flange using two types of tools; an Erbauer diamond tile drill bit and a Brad & Spur K10 drill. Six GFRP flanges were manufactured to reach the final product with acceptable quality and performance. The flange was adhesively bonded to a composite pipe after chamfering the end of the pipe. Another type of commercially-available composite flange was used to close the other end of the pipe. Finally, blind flanges were used to close both ends, making the pressure vessel that will be tested under the range of the bolt load and internal pressure.


Author(s):  
Roberto Barcala-Furelos ◽  
Cristian Abelairas-Gómez ◽  
Alejandra Alonso-Calvete ◽  
Francisco Cano-Noguera ◽  
Aida Carballo-Fazanes ◽  
...  

Abstract Introduction: On-boat resuscitation can be applied by lifeguards in an inflatable rescue boat (IRB). Due to Severe Acute Respiratory Syndrome Coronavirus-2 (SARS-COV-2) and recommendations for the use of personal protective equipment (PPE), prehospital care procedures need to be re-evaluated. The objective of this study was to determine how the use of PPE influences the amount of preparation time needed before beginning actual resuscitation and the quality of cardiopulmonary resuscitation (CPR; QCPR) on an IRB. Methods: Three CPR tests were performed by 14 lifeguards, in teams of two, wearing different PPE: (1) Basic PPE (B-PPE): gloves, a mask, and protective glasses; (2) Full PPE (F-PPE): B-PPE + a waterproof apron; and (3) Basic PPE + plastic blanket (B+PPE). On-boat resuscitation using a bag-valve-mask (BVM) and high efficiency particulate air (HEPA) filter was performed sailing at 20km/hour. Results: Using B-PPE takes less time and is significantly faster than F-PPE (B-PPE 17 [SD = 2] seconds versus F-PPE 69 [SD = 17] seconds; P = .001), and the use of B+PPE is slightly higher (B-PPE 17 [SD = 2] seconds versus B+PPE 34 [SD = 6] seconds; P = .002). The QCPR remained similar in all three scenarios (P >.05), reaching values over 79%. Conclusion: The use of PPE during on-board resuscitation is feasible and does not interfere with quality when performed by trained lifeguards. The use of a plastic blanket could be a quick and easy alternative to offer extra protection to lifeguards during CPR on an IRB.


2020 ◽  
Vol 79 (Suppl 1) ◽  
pp. 861-862
Author(s):  
Z. Izadi ◽  
T. Johansson ◽  
J. LI ◽  
G. Schmajuk ◽  
J. Yazdany

Background:The Rheumatology Informatics System for Effectiveness (RISE) Registry was developed by the ACR to help rheumatologists improve quality of care and meet federal reporting requirements. In the current quality program administered by the U.S. Centers for Medicare and Medicaid services, rheumatologists are scored on quality measures, and performance is tied to financial incentives or penalties. Rheumatoid arthritis (RA)-specific quality measures can only be submitted through RISE to federal programs.Objectives:This study used data from the RISE registry to investigate rheumatologists’ federal reporting patterns on five RA-specific quality measures in 2018 and investigated the effect of practice characteristics on federal reporting of these measures.Methods:We analyzed data on all rheumatologists who continuously participated in RISE between Jan 2017 to Dec 2018 and who had patients eligible for at least one RA-specific measure. Five measures were examined: tuberculosis screening before biologic use, disease activity assessment, functional status assessment, assessment and classification of disease prognosis, and glucocorticoid management. We assessed whether or not rheumatologists reported specific quality measures via RISE. We investigated the effect of practice characteristics (practice structure; number of providers; geographic region) on the likelihood of reporting using adjusted analyses that controlled for measure performance (performance in 2018; change in performance from 2017; and performance relative to national average performance). Analyses accounted for clustering by practice.Results:Data from 799 providers from 207 practices managing 213,757 RA patients was examined. The most common practice structure was a single-specialty group practice (53%), followed by solo (28%) and multi-specialty group practice (12%). Most providers (73%) had patients eligible for all five RA quality measures. Federal reporting of quality measures through RISE varied significantly by provider, ranging from no reporting (60%) to reporting all eligible RA measures (12.2%). Reporting through RISE also varied significantly by quality measure and was highest for functional status assessment (36%) and lowest for assessment and classification of disease prognosis (20%). Small practices (1-4 providers) were more likely to report all eligible RA quality measures compared to larger practices (21%, 6%; p<0.001). In adjusted analyses, solo practices were more likely than single-specialty group practices to report RA measures (42%, 31%; p<0.027) while multispecialty group practices were less likely (18%, 31%; p<0.001). Additionally, higher performance in 2018 and performance ≥ the national average performance was associated with federal reporting of the measures through RISE (p≤0.004).Conclusion:Forty percent of U.S. rheumatologists participating in RISE used the registry for federal quality reporting. Physicians using RISE for reporting were disproportionately in small and solo practices, suggesting that the registry is fulfilling an important role in helping these practices participate in national quality reporting programs. Supporting small practices is especially important given the workforce shortages in rheumatology. We observed that practices reporting through RISE had higher measure performance than other participating practices, which suggests that the registry is facilitating quality improvement. Studies are ongoing to further investigate the impact of federal quality reporting programs and RISE participation on the quality of rheumatologic care in the United States.Disclaimer: This data was supported by the ACR’s RISE Registry. However, the views expressed represent those of the authors, not necessarily those of the ACR.Disclosure of Interests:Zara Izadi: None declared, Tracy Johansson: None declared, Jing Li: None declared, Gabriela Schmajuk Grant/research support from: Pfizer, Jinoos Yazdany Grant/research support from: Pfizer


2020 ◽  
Vol 4 (6) ◽  
Author(s):  
Orna Intrator ◽  
Edward Alan Miller ◽  
Portia Y Cornell ◽  
Cari Levy ◽  
Christopher W Halladay ◽  
...  

Abstract Background and Objectives U.S. Department of Veterans Affairs Medical Centers (VAMCs) contract with nursing homes (NHs) in their community to serve Veterans. This study compares the characteristics and performance of Veterans Affairs (VA)-paid and non-VA-paid NHs both nationally and within local VAMC markets. Research Design and Methods VA-paid NHs were identified, characterized, and linked to VAMC markets using data drawn from VA administrative files. NHs in the United States in December 2015 were eligible for the analysis, including. 1,307 VA-paid NHs and 14,253 non-VA-paid NHs with NH Compare measures in 128 VAMC markets with any VA-paid NHs. Measurements were derived from the Centers for Medicare and Medicaid Services (CMS) five-star rating system, NH Compare. Results VA-paid NHs had more beds, residents per day, and were more likely to be for-profit relative to non-VA-paid NHs. Nationally, the average CMS NH Compare star rating was slightly lower among VA-paid NHs than non-VA-paid NHs (3.05 vs. 3.21, p = .04). This difference was seen in all 3 domains: inspection (3.11 vs. 3.23, p &lt; .001), quality (2.68 vs. 2.83, p &lt; .001), and total nurse staffing (3.36 vs. 3.42, p &lt; .10). There was wide variability across VAMC markets in the ratio of average star rating of VA-paid and non-VA-paid NHs (mean ratio = 0.93, interquartile range = 0.78–1.08). Discussion and Implications With increased community NH use expected following the implementation of the MISSION Act, comparison of the quality of purchased services to other available services becomes critical for ensuring quality, including for NH care. Methods presented in this article can be used to examine the quality of purchased care following the MISSION Act implementation. In particular, dashboards such as that for VA-paid NHs that compare to similar non-VA-paid NHs can provide useful information to quality improvement efforts.


Sign in / Sign up

Export Citation Format

Share Document