scholarly journals Estradiol Removal by Adsorptive Coating of a Microfiltration Membrane

Membranes ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 99
Author(s):  
Zahra Niavarani ◽  
Daniel Breite ◽  
Andrea Prager ◽  
Bernd Abel ◽  
Agnes Schulze
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Low Cost ◽  
High Water ◽  
Adsorption Properties ◽  
Experimental Conditions ◽  
Water Contact ◽  
Endocrine Disrupting Chemical ◽  
Pes Membrane

This work demonstrates the enhancement of the adsorption properties of polyethersulfone (PES) microfiltration membranes for 17β-estradiol (E2) from water. This compound represents a highly potent endocrine-disrupting chemical (EDC). The PES membranes were modified with a hydrophilic coating functionalized by amide groups. The modification was performed by the interfacial reaction between hexamethylenediamine (HMD) or piperazine (PIP) as the amine monomer and trimesoyl chloride (TMC) or adipoyl chloride (ADC) as the acid monomer on the surface of the membrane using electron beam irradiation. The modified membranes and the untreated PES membrane were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), water permeance measurements, water contact angle measurements, and adsorption experiments. Furthermore, the effects of simultaneous changes in four modification parameters: amine monomer types (HMD or PIP), acid monomer types (TMC or ADC), irradiation dosage (150 or 200 kGy), and the addition of toluene as a swelling agent, on the E2 adsorption capacity were investigated. The results showed that the adsorption capacities of modified PES membranes toward E2 are >60%, while the unmodified PES membrane had an adsorption capacity up to 30% for E2 under similar experimental conditions, i.e., an enhancement of a factor of 2. Next to the superior adsorption properties, the modified PES membranes maintain high water permeability and no pore blockage was observed. The highlighted results pave the way to develop efficient low-cost, stable, and high-performance adsorber membranes.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

scholarly journals Ultralow-temperature-driven water-based sorption refrigeration enabled by low-cost zeolite-like porous aluminophosphate

2022 ◽  
Vol 13 (1) ◽  
Author(s):  
Zhangli Liu ◽  
Jiaxing Xu ◽  
Min Xu ◽  
Caifeng Huang ◽  
Ruzhu Wang ◽  
...  
Keyword(s):  
Low Temperature ◽  
Water Sorption ◽  
High Performance ◽  
Global Climate ◽  
Low Cost ◽  
Cost Effective ◽  
High Water ◽  
Coefficient Of Performance ◽  
High Efficient ◽  
Water Based

AbstractThermally driven water-based sorption refrigeration is considered a promising strategy to realize near-zero-carbon cooling applications by addressing the urgent global climate challenge caused by conventional chlorofluorocarbon (CFC) refrigerants. However, developing cost-effective and high-performance water-sorption porous materials driven by low-temperature thermal energy is still a significant challenge. Here, we propose a zeolite-like aluminophosphate with SFO topology (EMM-8) for water-sorption-driven refrigeration. The EMM-8 is characterized by 12-membered ring channels with large accessible pore volume and exhibits high water uptake of 0.28 g·g−1 at P/P0 = 0.2, low-temperature regeneration of 65 °C, fast adsorption kinetics, remarkable hydrothermal stability, and scalable fabrication. Importantly, the water-sorption-based chiller with EMM-8 shows the potential of achieving a record coefficient of performance (COP) of 0.85 at an ultralow-driven temperature of 63 °C. The working performance makes EMM-8 a practical alternative to realize high-efficient ultra-low-temperature-driven refrigeration.

scholarly journals Nanosheets of CuCo2O4 As a High-Performance Electrocatalyst in Urea Oxidation

2019 ◽  
Vol 9 (4) ◽  
pp. 793 ◽  
Author(s):  
Camila Zequine ◽  
Fangzhou Wang ◽  
Xianglin Li ◽  
Deepa Guragain ◽  
S.R. Mishra ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Nickel Foam ◽  
Low Cost ◽  
Agricultural Waste ◽  
Bifunctional Catalyst ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electroactive Material

The urea oxidation reaction (UOR) is a possible solution to solve the world’s energy crisis. Fuel cells have been used in the UOR to generate hydrogen with a lower potential compared to water splitting, decreasing the costs of energy production. Urea is abundantly present in agricultural waste and in industrial and human wastewater. Besides generating hydrogen, this reaction provides a pathway to eliminate urea, which is a hazard in the environment and to people’s health. In this study, nanosheets of CuCo2O4 grown on nickel foam were synthesized as an electrocatalyst for urea oxidation to generate hydrogen as a green fuel. The synthesized electrocatalyst was characterized using X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy. The electroactivity of CuCo2O4 towards the oxidation of urea in alkaline solution was evaluated using electrochemical measurements. Nanosheets of CuCo2O4 grown on nickel foam required the potential of 1.36 V in 1 M KOH with 0.33 M urea to deliver a current density of 10 mA/cm2. The CuCo2O4 electrode was electrochemically stable for over 15 h of continuous measurements. The high catalytic activities for the hydrogen evolution reaction make the CuCo2O4 electrode a bifunctional catalyst and a promising electroactive material for hydrogen production. The two-electrode electrolyzer demanded a potential of 1.45 V, which was 260 mV less than that for the urea-free counterpart. Our study suggests that the CuCo2O4 electrode can be a promising material as an efficient UOR catalyst for fuel cells to generate hydrogen at a low cost.

Insights into the mechanism of methylene blue removed by novel and classic biochars

2019 ◽  
Vol 79 (8) ◽  
pp. 1561-1570
Author(s):  
Wei Chen ◽  
Fengting Chen ◽  
Bin Ji ◽  
Lin Zhu ◽  
Hongjiao Song
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Low Cost ◽  
Underlying Mechanism ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Average Pore ◽  
Adsorption Effect ◽  
Magnolia Grandiflora

Abstract The adsorption behavior and the underlying mechanism of methylene blue (MB) sorption on biochars prepared from different feedstocks at 500 °C were evaluated. The biochar feedstocks included Magnolia grandiflora Linn. leaves biochar (MBC), pomelo (Citrus grandis) peel biochar (PBC) and badam shell biochar (BBC). The results of characterizing and analyzing the samples showed that different biochars had different effects on the adsorption of MB. It could be found that MBC had the best adsorption effect on MB due to its largest average pore diameter of 5.55 nm determined by Brunauer-Emmett-Teller analysis. Under the optimal conditions, the maximum adsorption capacities of BBC, PBC and MBC were 29.7, 85.15 and 99.3 mg/g, respectively. The results showed that the amount of adsorption was affected by the pH value. The maximum adsorption capacity of MBC was 46.99 mg/g when it was at pH of 3, whereas for the same experimental conditions the maximum adsorption capacity of BBC and PBC was 25.29 mg/g at pH of 11 and 36.08 mg/g at pH of 7, respectively. Therefore, MBC was found to be a most efficient low-cost adsorbentl for dye wastewater treatment compared with BBC and PBC, and it had the best removal effect under acidic conditions.

scholarly journals Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

2021 ◽  
Author(s):  
You Wu ◽  
Zuannian Liu ◽  
Bakhtari Mohammad Fahim ◽  
Junnan Luo
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Adsorption Mechanism ◽  
Nitrogen Adsorption ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Mechanisms ◽  
Adsorption Desorption

Abstract In this study, MIL-101(Fe), MIL-101(Fe,Cu), and Graphene Oxide (GO) /MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOFs-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including reaction time, pH, temperature and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g− 1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m2/g is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe),which are 747.75 and 510.66m2/g respectively. The adsorption mechanism of phosphate is electrostatic attraction, form coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

scholarly journals Incorporating N Atoms into SnO2 Nanostructure as an Approach to Enhance Gas Sensing Property for Acetone

Nanomaterials ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 445 ◽  
Author(s):  
Xiangfeng Guan ◽  
Yongjing Wang ◽  
Peihui Luo ◽  
Yunlong Yu ◽  
Dagui Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Gas Sensor ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Gas Sensing ◽  
Diffuse Reflectance Spectroscopy ◽  
Limit Of Detection ◽  
Low Cost ◽  
X Ray ◽  
Sno2 Nanostructure

The development of high-performance acetone gas sensor is of great significance for environmental protection and personal safety. SnO2 has been intensively applied in chemical sensing areas, because of its low cost, high mobility of electrons, and good chemical stability. Herein, we incorporated nitrogen atoms into the SnO2 nanostructure by simple solvothermal and subsequent calcination to improve gas sensing property for acetone. The crystallization, morphology, element composition, and microstructure of as-prepared products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Electron paramagnetic resonance (EPR), Raman spectroscopy, UV–visible diffuse reflectance spectroscopy (UV–vis DRS), and the Brunauer–Emmett–Teller (BET) method. It has been found that N-incorporating resulted in decreased crystallite size, reduced band-gap width, increased surface oxygen vacancies, enlarged surface area, and narrowed pore size distribution. When evaluated as gas sensor, nitrogen-incorporated SnO2 nanostructure exhibited excellent sensitivity for acetone gas at the optimal operating temperature of 300 °C with high sensor response (Rair/Rgas − 1 = 357) and low limit of detection (7 ppb). The nitrogen-incorporated SnO2 gas sensor shows a good selectivity to acetone in the interfering gases of benzene, toluene, ethylbenzene, hydrogen, and methane. Furthermore, the possible gas-sensing mechanism of N-incorporated SnO2 toward acetone has been carefully discussed.

Fabrication of Superhydrophobic Surfaces on Copper Foil with Stearic Acid

2011 ◽  
Vol 295-297 ◽  
pp. 921-924 ◽  
Author(s):  
Li Bo Wang ◽  
Yang Lu ◽  
Xin Xin Cao
Keyword(s):  
Stearic Acid ◽  
Photoelectron Spectroscopy ◽  
Pure Copper ◽  
Copper Substrate ◽  
High Water ◽  
Random Pattern ◽  
Mixed Solution ◽  
Sem Images ◽  
Water Contact ◽  
Porous Architecture

Superhydrophobic surface was prepared by hydrothermal method on copper substrate via immersing the clean pure copper substrate into the mixed solution of H2O2and C2H5OH, and then the substrate was heated at 100°C for 1.5 h, followed by modifying with stearic acid. The product was characterized by scanning electron microscopy and X-ray photoelectron spectroscopy. The wettability of the products was also investigated. It was found that the as-prepared surface had a high water contact angle of about 153°. SEM images of the film showed that many irregular micro-nano sheets distributed on the surface in a random pattern. The special porous architecture, with the low surface energy leads to the surface superhydrophobicity.

East Asian Calligraphy Black Ink-Coated Paper as Flexible Conducting Electrode for Supercapacitor

2021 ◽  
Author(s):  
Ren-Jie Xie ◽  
I-Chun Cheng ◽  
Jian-Zhang Chen
Keyword(s):  
Flexible Electronics ◽  
Photoelectron Spectroscopy ◽  
Low Cost ◽  
East Asian ◽  
Electrical Conductance ◽  
Angle Measurement ◽  
Bending Test ◽  
Coated Paper ◽  
Water Contact ◽  
X Ray

Abstract East Asian calligraphy black ink (hereafter called simply “black ink”) is used to fabricate flexible conducting chromatography paper electrode by a simple and low-cost method. The black ink-coated paper was characterized by scanning electron microscopy, surface profiler, water contact angle measurement, electrical resistance measurement, X-ray photoelectron spectroscopy, and X-ray diffraction. The hydrophilicity slightly decreased after black ink coating but still provided good adhesion to the follow-up reduced graphene oxide/polyaniline/chitosan slurry coating for fabricating supercapacitor electrodes. A 1000-cycle repeated bending test with a bending radius of 5 mm revealed good conductance retention. Instrumental analyses indicated that the carbon black in the black ink was the main contributor to the electrical conductance. The supercapacitor with black-ink-coated paper electrodes exhibited an areal specific capacitance of up to 179.08 mF/cm² and coulomb efficiency of 80%. This confirmed that the black-ink-coated paper electrode could be feasibly applied to a supercapacitor. This black-ink-coated paper can be easily fabricated in resource-limited settings, and it provides new possibilities for the use of paper-based electrodes in flexible electronics.

scholarly journals Detoxification, Active Uptake, and Intracellular Accumulation of Chromium Species by a Methane-Oxidizing Bacterium

2020 ◽  
Vol 87 (2) ◽  
Author(s):  
Salaheldeen Enbaia ◽  
Abdurrahman Eswayah ◽  
Nicole Hondow ◽  
Philip H. E. Gardiner ◽  
Thomas J. Smith
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
High Performance ◽  
Low Cost ◽  
Cell Fractionation ◽  
Methylococcus Capsulatus ◽  
Chromium Species ◽  
Content Type ◽  
X Ray ◽  
Chromium Vi

ABSTRACT Despite the wide-ranging proscription of hexavalent chromium, chromium(VI) remains among the major polluting heavy metals worldwide. Aerobic methane-oxidizing bacteria are widespread environmental microorganisms that can perform diverse reactions using methane as the feedstock. The methanotroph Methylococcus capsulatus Bath, like many other microorganisms, detoxifies chromium(VI) by reduction to chromium(III). Here, the interaction of chromium species with M. capsulatus Bath was examined in detail by using a range of techniques. Cell fractionation and high-performance liquid chromatography–inductively coupled plasma mass spectrometry (HPLC–ICP-MS) indicated that externally provided chromium(VI) underwent reduction and was then taken up into the cytoplasmic and membranous fractions of the cells. This was confirmed by X-ray photoelectron spectroscopy (XPS) of intact cultures that indicated negligible chromium on the surfaces of or outside the cells. Distribution of chromium and other elements within intact and sectioned cells, as observed via transmission electron microscopy (TEM) combined with energy-dispersive X-ray spectroscopy (EDX) and electron energy loss spectroscopy (EELS), was consistent with the cytoplasm/membrane location of the chromium(III), possibly as chromium phosphate. The cells could also take up chromium(III) directly from the medium in a metabolism-dependent fashion and accumulate it. These results indicate a novel pattern of interaction with chromium species distinct from that observed previously with other microorganisms. They also suggest that M. capsulatus and similar methanotrophs may contribute directly to chromium(VI) reduction and accumulation in mixed communities of microorganisms that are able to perform methane-driven remediation of chromium(VI). IMPORTANCE M. capsulatus Bath is a well-characterized aerobic methane-oxidizing bacterium that has become a model system for biotechnological development of methanotrophs to perform useful reactions for environmental cleanup and for making valuable chemicals and biological products using methane gas. Interest in such technology has increased recently owing to increasing availability of low-cost methane from fossil and biological sources. Here, it is demonstrated that this versatile methanotroph can reduce the toxic contaminating heavy metal chromium(VI) to the less toxic form chromium(III) while accumulating the chromium(III) within the cells. This is expected to diminish the bioavailability of the chromium and make it less likely to be reoxidized to chromium(VI). Thus, M. capsulatus has the capacity to perform methane-driven remediation of chromium-contaminated water and other materials and to accumulate the chromium in the low-toxicity chromium(III) form within the cells.

scholarly journals Turning Tissue Waste into High-Performance Microfiber Filters for Oily Wastewater Treatment

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 378
Author(s):  
Gaoliang Wei ◽  
Jun Dong ◽  
Jing Bai ◽  
Yongsheng Zhao ◽  
Chuanyu Qin
Keyword(s):  
Contact Angle ◽  
Wastewater Treatment ◽  
High Performance ◽  
Low Cost ◽  
Oily Wastewater ◽  
Water Contact ◽  
Oil Mixtures ◽  
Oil Water ◽  
Oily Wastewater Treatment ◽  
Underwater Superoleophobicity

Developing low-cost, durable, and high-performance materials for the separation of water/oil mixtures (free oil/water mixtures and emulsions) is critical to wastewater treatment and resource recovery. However, this currently remains a challenge. In this work, we report a biopolymer microfiber assembly, fabricated from the recovery of tissue waste, as a low-cost and high-performance filter for oily wastewater treatment. The microfiber filters demonstrate superhydrophilicity (water contact angle of 28.8°) and underwater superoleophobicity (oil contact angle of 154.2°), and thus can achieve separation efficiencies of >96% for both free oil/water mixtures and surfactant-stabilized emulsions even in highly acidic (pH 2.2)/alkaline (pH 11.8) conditions. Additionally, the prepared microfiber filters possess a much higher resistance to oil fouling than conventional membranes when filtering emulsions, which is because the large-sized 3D interconnected channels of the filters can delay the formation of a low-porosity oil gel layer on their surface. The filters are expected to practically apply for the oily wastewater treatment and reduce the amount of tissue waste entering the environment.

Sign in / Sign up

Export Citation Format

Share Document