scholarly journals A Phenomenological Mechanical Material Model for Precipitation Hardening Aluminium Alloys

Metals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 1165 ◽  
Author(s):  
Hannes Fröck ◽  
Lukas Vincent Kappis ◽  
Michael Reich ◽  
Olaf Kessler
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Finite Element ◽  
Phase Transformation ◽  
Aluminium Alloys ◽  
Material Model ◽  
Heat Treatments ◽  
Maximum Temperature ◽  
Finite Element Software ◽  
Welding Processes

Age hardening aluminium alloys obtain their strength by forming precipitates. This precipitation-hardened state is often the initial condition for short-term heat treatments, like welding processes or local laser heat treatment to produce tailored heat-treated profiles (THTP). During these heat treatments, the strength-increasing precipitates are dissolved depending on the maximum temperature and the material is softened in these areas. Depending on the temperature path, the mechanical properties differ between heating and cooling at the same temperature. To model this behavior, a phenomenological material model was developed based on the dissolution characteristics and experimental flow curves were developed depending on the current temperature and the maximum temperature. The dissolution characteristics were analyzed by calorimetry. The mechanical properties at different temperatures and peak temperatures were recorded by thermomechanical analysis. The usual phase transformation equations in the Finite Element Method (FEM) code, which were developed for phase transformation in steels, were used to develop a phenomenological model for the mechanical properties as a function of the relevant heat treatment parameters. This material model was implemented for aluminium alloy 6060 T4 in the finite element software LS-DYNA (Livermore Software Technology Corporation).

Precipitation Behaviour and Mechanical Properties during Short-Term Heat Treatment for Tailor Heat Treated Profiles (THTP) of Aluminium Alloy 6060 T4

2016 ◽  
Vol 877 ◽  
pp. 400-406 ◽  
Author(s):  
Hannes Fröck ◽  
Matthias Graser ◽  
Benjamin Milkereit ◽  
Michael Reich ◽  
Michael Lechner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminium Alloy ◽  
Heat Treatments ◽  
Maximum Temperature ◽  
Short Term ◽  
Scanning Calorimetry ◽  
Heat Treated ◽  
Precipitation Behaviour ◽  
Dissolution And Precipitation

Precipitation hardening aluminium alloys are widely used for automotive applications. To enhance the application of aluminium profiles, improved formability is needed. Tailor Heat Treated Profiles (THTP) with locally different material properties attempt to increase formability e.g. in bending processes. Tailoring of local properties is obtained by a local short-term heat treatment, dissolving the initial precipitate state (retrogression) and still allowing subsequent ageing. In the present study, the dissolution and precipitation behaviour of the aluminium alloy EN AW-6060 T4 was investigated during heating with differential scanning calorimetry (DSC). Heating curves from 20 to 600 °C with heating rates of 0.01 up to 5 K/s were recorded. Interrupted heat treatments with different maximum temperatures were performed in a deformation dilatometer. Immediately afterwards, tensile tests were carried out at room temperature. The course of the recorded mechanical properties as a function of the maximum temperature is discussed with regard to the dissolution and precipitation behaviour during heating. Finally, the aging behaviour of the investigated alloy was recorded after different typical short-term heat treatments and is discussed with reference to the DSC‐curves. The correlation of the microstructure and the mechanical properties enables the derivation of optimal parameters for the development of THTP through a local softening.

scholarly journals Characterization of Mechanical Heterogeneity in Dissimilar Metal Welded Joints

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4145
Author(s):  
He Xue ◽  
Zheng Wang ◽  
Shuai Wang ◽  
Jinxuan He ◽  
Hongliang Yang
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Welded Joints ◽  
Structural Integrity ◽  
Material Interfaces ◽  
Mechanical Heterogeneity ◽  
Finite Element Software ◽  
Dissimilar Metal ◽  
Stress Changes

Dissimilar metal welded joints (DMWJs) possess significant localized mechanical heterogeneity. Using finite element software ABAQUS with the User-defined Material (UMAT) subroutine, this study proposed a constitutive equation that may be used to express the heterogeneous mechanical properties of the heat-affected and fusion zones at the interfaces in DMWJs. By eliminating sudden stress changes at the material interfaces, the proposed approach provides a more realistic and accurate characterization of the mechanical heterogeneity in the local regions of DMWJs than existing methods. As such, the proposed approach enables the structural integrity of DMWJs to be analyzed in greater detail.

Calculating Mechanics Characteristics of Single-Walled Carbon Nanotube Materials by Finite Element Method

2017 ◽  
Vol 730 ◽  
pp. 548-553
Author(s):  
Jing Ge ◽  
Hao Jiang ◽  
Zhen Yu Sun ◽  
Guo Jun Yu ◽  
Bo Su ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Radial Direction ◽  
Element Model ◽  
Beam Element ◽  
Beam Position ◽  
Single Walled Carbon ◽  
Finite Element Software ◽  
Calculation Results ◽  
The Moment

In this paper, we establish the mechanical property analysis of Single-walled Carbon Nanotubes (SWCNTs) modified beam element model based on the molecular structural mechanics method. Then we study the mechanical properties of their radial direction characteristics using the finite element software Abaqus. The model simulated the different bending stiffness with rectangular section beam elements C-C chemical force field. When the graphene curled into arbitrary chirality of SWCNTs spatial structure, the adjacent beam position will change the moment of inertia of the section of the beam. Compared with the original beam element model and the calculation results, we found that the established model largely reduced the overestimate of the original model of mechanical properties on the radial direction of the SWCNTs. At the same time, compared with other methods available in the literature results and the experimental data, the results can be in good agreement.

Influence of Heat Treatment on Microstructure and Mechanical Properties of Selective Laser Melted TiAl6V4 Alloy

2018 ◽  
Vol 284 ◽  
pp. 615-620 ◽  
Author(s):  
R.M. Baitimerov ◽  
P.A. Lykov ◽  
L.V. Radionova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Selective Laser Melting ◽  
Room Temperature ◽  
Base Alloy ◽  
Tensile Tests ◽  
Heat Treatments ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Treatment Procedures

TiAl6V4 titanium base alloy is widely used in aerospace and medical industries. Specimens for tensile tests from TiAl6V4 with porosity less than 0.5% was fabricated by selective laser melting (SLM). Specimens were treated using two heat treatment procedures, third batch of specimens was tested in as-fabricated statement after machining. Tensile tests were carried out at room temperature. Microstructure and mechanical properties of SLM fabricated TiAl6V4 after different heat treatments were investigated.

scholarly journals Numerical simulation of blanking process

2018 ◽  
Vol 157 ◽  
pp. 02038
Author(s):  
Peter Pecháč ◽  
Milan Sága
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Steel Sheet ◽  
Plastic Material ◽  
Material Model ◽  
Rolled Steel ◽  
Finite Element Software ◽  
History Of ◽  
Cold Rolled ◽  
Blanking Process

This paper presents numerical simulation of blanking process for cold-rolled steel sheet metal. The problem was modeled using axial symmetry in commercial finite element software ADINA. Data obtained by experimental measurement were used to create multi-linear plastic material model for simulation. History of blanking force vs. tool displacement was obtained.

scholarly journals Electron Beam Melting of Ti-6Al-4V Lattice Structures; Correlation between Post Heat Treatment and Mechanical Properties

2021 ◽  
Author(s):  
Giuseppe Del Guercio ◽  
Manuela Galati ◽  
Abdollah Saboori
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Computer Aided Design ◽  
Mechanical Performance ◽  
Industrial Applications ◽  
Heat Treatments ◽  
Layer By Layer ◽  
Lattice Structures ◽  
Heat Treated ◽  
Aided Design

Abstract Additive Manufacturing processes are considered advanced manufacturing methods. It would be possible to produce complex shape components from a Computer-Aided Design model in a layer-by-layer manner. Lattice structures as one of the complex geometries could attract lots of attention for both medical and industrial applications. In these structures, besides cell size and cell type, the microstructure of lattice structures can play a key role in these structures' mechanical performance. On the other hand, heat treatment has a significant influence on the mechanical properties of the material. Therefore, in this work, the effect of the heat treatments on the microstructure and mechanical behaviour of Ti-6Al-4V lattice structures manufactured by EBM was analyzed. The main mechanical properties were compared with the Ashby and Gibson model. It is very interesting to notice that a more homogeneous failure mode was found for the heat-treated samples. The structures' relative density was the main factor influencing their mechanical performance of the heat-treated samples. It is also found that the heat treatments were able to preserve the stiffness and the compressive strength of the lattice structures. Besides, an increment of both the elongation at failure and the absorbed energy was obtained after the heat treatments. Microstructure analysis of the heat-treated samples confirms the increment of ductility of the heat-treated samples with respect to the as-built one.

Influence of imperfections on the stiffness of regular scaffold structures

2016 ◽  
Vol 232 (6) ◽  
pp. 453-464
Author(s):  
Ainhoa Martinez Ormaetxea ◽  
Andreas Öchsner
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Programming Language ◽  
Manufacturing Process ◽  
Experimental Testing ◽  
Bone Scaffold ◽  
Finite Element Software ◽  
Different Types ◽  
Data Files ◽  
Load Conditions

The manufacturing process of bone scaffold structures has an important influence on the final mechanical strength of the structure. When the structures are not produced properly, i.e. have imperfections such as missing parts or slightly displaced joints, they lose some of their mechanical properties. The aim of this study was to see how different types of damage affect the structures and also if their effects are equal when the structure is subjected to different load conditions. The change of the mechanical behavior was determined using the commercial finite element software MSC Marc Mentat. In turn, the damage was introduced by manipulating the structure’s files (ASCII data files) using the programming language Fortran. Apart from the numerical simulations, experimental testing was also performed to verify the numerical results. In the frame of this study, useful information for further research is provided.

Effect of heat treatment on the phase transformation and mechanical properties of Ti6Al4V fabricated by selective laser melting

2018 ◽  
Vol 764 ◽  
pp. 1056-1071 ◽  
Author(s):  
Xingchen Yan ◽  
Shuo Yin ◽  
Chaoyue Chen ◽  
Chunjie Huang ◽  
Rodolphe Bolot ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Transformation ◽  
Selective Laser Melting ◽  
Laser Melting
Sign in / Sign up

Export Citation Format

Share Document