scholarly journals Solar Light-Induced Methylene Blue Removal over TiO2/AC Composites and Photocatalytic Regeneration

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3016
Author(s):  
Fernanda Dalto ◽  
Iwona Kuźniarska-Biernacka ◽  
Clara Pereira ◽  
Elsa Mesquita ◽  
Olívia Salomé G. P. Soares ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Wastewater Treatment ◽  
Photoelectron Spectroscopy ◽  
Treatment Plant ◽  
Bulk Water ◽  
Solar Irradiation ◽  
Secondary Effluent ◽  
Ultrapure Water ◽  
X Ray ◽  
Reflectance Ftir

TiO2-containing photocatalysts, which combine TiO2 with carbon-based materials, are promising materials for wastewater treatment due to synergistic photodegradation and adsorption phenomena. In this work, TiO2/AC composites were produced by the in situ immobilization of TiO2 nanoparticles over activated carbon (AC) derived from spent coffee grains, using different TiO2/AC proportions. The TiO2/AC composites were tested as adsorbents (dark) and as photocatalysts in a combined adsorption+photocatalytic process (solar irradiation) for methylene blue (MB) removal from ultrapure water, and from a secondary effluent (SecEf) of an urban wastewater treatment plant. All the materials were characterized by XRD (X-ray powder diffraction), N2 adsorption–desorption isotherms at −196 °C, SEM (scanning electron microscopy), UV-Vis diffuse reflectance, FTIR (Fourier-transform infrared spectroscopy), TPD (temperature programmed desorption), XPS (X-ray photoelectron spectroscopy) and TGA (thermogravimetric analysis). The TiAC60 (60% C) composite presented the lowest band gap (1.84 eV), while, for TiAC29 (29% C), the value was close to that of bare TiO2 (3.18 vs. 3.17 eV). Regardless of the material, the solar irradiation improved the percentage of MB discolouration when compared to adsorption in dark conditions. In the case of simultaneous adsorption+photocatalytic assays performed in ultrapure water, TiAC29 presented the fastest MB removal. Nevertheless, both TiAC29 and TiAC60 led to excellent MB removal percentages (96.1–98.1%). UV-induced photoregeneration was a promising strategy to recover the adsorption capacity of the materials, especially for TiAC60 and AC (>95%). When the assays were performed in SecEf, all the materials promoted discolouration percentages close to those obtained in ultrapure water. The bulk water parameters revealed that TiAC60 allowed the removal of a higher amount of MB, associated with the overall improvement of the SecEf quality.

scholarly journals Removal of Carbamazepine onto Modified Zeolitic Tuff in Different Water Matrices: Batch and Continuous Flow Experiments

Water ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1084
Author(s):  
Othman A. Al-Mashaqbeh ◽  
Diya A. Alsafadi ◽  
Layal Z. Alsalhi ◽  
Shannon L. Bartelt-Hunt ◽  
Daniel D. Snow
Keyword(s):  
Wastewater Treatment ◽  
Sorption Capacity ◽  
Pure Water ◽  
Treatment Plant ◽  
Hexadecyltrimethylammonium Bromide ◽  
Ultrapure Water ◽  
Zeolitic Tuff ◽  
X Ray ◽  
Wwtp Effluent ◽  
Surfactant Modification

Carbamazepine (CBZ) is the most frequently detected pharmaceutical residues in aquatic environments effluent by wastewater treatment plants. Batch and column experiments were conducted to evaluate the removal of CBZ from ultra-pure water and wastewater treatment plant (WWTP) effluent using raw zeolitic tuff (RZT) and surfactant modified zeolite (SMZ). Point zero net charge (pHpzc), X-ray diffraction (XRD), X-ray fluorescence (XRF), and Fourier Transform Infrared (FTIR) were investigated for adsorbents to evaluate the physiochemical changes resulted from the modification process using Hexadecyltrimethylammonium bromide (HDTMA-Br). XRD and FTIR showed that the surfactant modification of RZT has created an amorphous surface with new alkyl groups on the surface. The pHpzc was determined to be approximately 7.9 for RZT and SMZ. The results indicated that the CBZ uptake by SMZ is higher than RZT in all sorption tests (>8 fold). Batch results showed that the sorption capacity of RZT and SMZ in WWTP effluent (0.029 and 0.25 mg/g) is higher than RZT and SMZ (0.018 and 0.14 mg/g) in ultrapure water (1.6–1.8 fold). Batch tests showed that the equilibrium time of CBZ removal in the WWTP matrix (47 h) is much longer than CBZ removal in ultrapure water. The sorption capacity of RZT & SMZ in WWTP effluent (0.03, 0.33 mg/g) is higher than RZT and SMZ (0.02 and 0.17 mg/g) in ultrapure water (1.5–2 fold) using column test. This study has clearly demonstrated that the performance of RZT and SMZ is more efficient for the removal of CBZ from realistic wastewater than ultrapure water. It is evident that the surfactant modification of RZT has enhanced the CBZ removal in both matrices.

WASTEWATER DISINFECTION BY UV AT TRANI MUNICIPAL PLANT

1994 ◽  
Vol 30 (4) ◽  
pp. 125-132 ◽  
Author(s):  
D. Carnimeo ◽  
E. Contini ◽  
R. Di Marino ◽  
F. Donadio ◽  
L. Liberti ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Continuous Operation ◽  
Secondary Effluent ◽  
Municipal Wastewater Treatment ◽  
South Italy ◽  
Wastewater Disinfection ◽  
Pilot Investigation ◽  
Effluent Characteristics

The pilot investigation on the use of UV as an alternative disinfectant to NaOCI was started in 1992 at Trani (South Italy) municipal wastewater treatment plant (335 m3/h). The results collected after six months continuous operation enabled us to compare UV and NaOCl disinfection effectiveness on the basis of secondary effluent characteristics, quantify photoreactivation effects, evidence possible DBP formation and assess costs.

Textile Wastewater Reuse: Ozonation of Membrane Concentrated Secondary Effluent

1999 ◽  
Vol 40 (4-5) ◽  
pp. 99-105 ◽  
Author(s):  
A. Lopez ◽  
G. Ricco ◽  
R. Ciannarella ◽  
A. Rozzi ◽  
A. C. Di Pinto ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Acute Toxicity ◽  
Wastewater Treatment Plant ◽  
Textile Industry ◽  
Nonionic Surfactants ◽  
Wastewater Reuse ◽  
Treatment Plant ◽  
Textile Wastewater ◽  
Secondary Effluent ◽  
Complete Disappearance

Among the activities appointed by the EC research-project “Integrated water recycling and emission abatement in the textile industry” (Contract: ENV4-CT95-0064), the effectiveness of ozone for improving the biotreatability of recalcitrant effluents as well as for removing from them toxic and/or inhibitory pollutants has been evaluated at lab-scale. Real membrane concentrates (pH=7.9; TOC=190 ppm; CDO=595 ppm; BOD5=0 ppm; Conductivity=5,000 μS/cm; Microtox-EC20=34%) produced at Bulgarograsso (Italy) Wastewater Treatment Plant by nanofiltering biologically treated secondary textile effluents, have been treated with ozonated air (O3conc.=12 ppm) over 120 min. The results have indicated that during ozonation, BOD5 increases from 0 to 75 ppm, whereas COD and TOC both decrease by about 50% and 30 % respectively. As for potentially toxic and/or inhibitory pollutants such as dyes, nonionic surfactants and halogenated organics, all measured as sum parameters, removals higher than 90% were achieved as confirmed by the complete disappearance of acute toxicity in the treated streams. The only ozonation byproducts searched for and found were aldehydes whose total amount continuously increased in the first hour from 1.2 up to 11.8 ppm. Among them, formaldehyde, acetaldehyde, glyoxal, propionaldehyde, and butyraldehyde were identified by HPLC.

scholarly journals Efficient Adsorption of Methylene Blue by Porous Biochar Derived from Soybean Dreg Using a One-Pot Synthesis Method

Molecules ◽  
2021 ◽  
Vol 26 (3) ◽  
pp. 661
Author(s):  
Zhiwei Ying ◽  
Xinwei Chen ◽  
He Li ◽  
Xinqi Liu ◽  
Chi Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
Urban Pollution ◽  
Maximum Adsorption Capacity ◽  
One Pot ◽  
Average Pore ◽  
X Ray ◽  
Isotherm Equation

Soybean dreg is a by-product of soybean products production, with a large consumption in China. Low utilization value leads to random discarding, which is one of the important sources of urban pollution. In this work, porous biochar was synthesized using a one-pot method and potassium bicarbonate (KHCO3) with low-cost soybean dreg (SD) powder as the carbon precursor to investigating the adsorption of methylene blue (MB). The prepared samples were characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM), elemental analyzer (EA), Brunauer-Emmett-Teller (BET), X-ray diffractometer (XRD), Raman spectroscopy (Raman), Fourier transform infrared spectrometer (FTIR), and X-ray photoelectron spectroscopy (XPS). The obtained SDB-K-3 showed a high specific surface area of 1620 m2 g−1, a large pore volume of 0.7509 cm3 g−1, and an average pore diameter of 1.859 nm. The results indicated that the maximum adsorption capacity of SDB-K-3 to MB could reach 1273.51 mg g−1 at 318 K. The kinetic data were most consistent with the pseudo-second-order model and the adsorption behavior was more suitable for the Langmuir isotherm equation. This study demonstrated that the porous biochar adsorbent can be prepared from soybean dreg by high value utilization, and it could hold significant potential for dye wastewater treatment in the future.

scholarly journals Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 558
Author(s):  
Wenhui Zhu ◽  
Caiyun Zhang ◽  
Yali Chen ◽  
Qiliang Deng
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Degradation Rate ◽  
Model Compound ◽  
Vibrating Sample Magnetometer ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

scholarly journals Decolorization of Methylene Blue by Ag/SrSnO3 Composites under Ultraviolet Radiation

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Patcharanan Junploy ◽  
Titipun Thongtem ◽  
Somchai Thongtem ◽  
Anukorn Phuruangrat
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Separation Process ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Negative Effect ◽  
Uv Visible

SrSn(OH)6 precursors synthesized by a cyclic microwave radiation (CMR) process were calcined at 900°C for 3 h to form rod-like SrSnO3. Further, the rod-like SrSnO3 and AgNO3 in ethylene glycol (EG) were ultrasonically vibrated to form rod-like Ag/SrSnO3 composites, characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy (EM), Fourier transform infrared (FTIR) spectroscopy, and UV-visible analysis. The photocatalyses of rod-like SrSnO3, 1 wt%, 5 wt%, and 10 wt% Ag/SrSnO3 composites were studied for degradation of methylene blue (MB, C16H18N3SCl) dye under ultraviolet (UV) radiation. In this research, the 5 wt% Ag/SrSnO3 composites showed the highest activity, enhanced by the electron-hole separation process. The photoactivity became lower by the excessive Ag nanoparticles due to the negative effect caused by reduction in the absorption of UV radiation.

scholarly journals Facile Preparation of Rod-like MnO Nanomixtures via Hydrothermal Approach and Highly Efficient Removal of Methylene Blue for Wastewater Treatment

Nanomaterials ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 10 ◽  
Author(s):  
Yuelong Xu ◽  
Bin Ren ◽  
Ran Wang ◽  
Lihui Zhang ◽  
Tifeng Jiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Degradation Mechanism ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Transmission Electron ◽  
Degradation Ratio ◽  
Hydrothermal Approach

In the present study, nanoscale rod-shaped manganese oxide (MnO) mixtures were successfully prepared from graphitic carbon nitride (C3N4) and potassium permanganate (KMnO4) through a hydrothermal method. The as-prepared MnO nanomixtures exhibited high activity in the adsorption and degradation of methylene blue (MB). The as-synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), surface area analysis, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Furthermore, the effects of the dose of MnO nanomixtures, pH of the solution, initial concentration of MB, and the temperature of MB removal in dye adsorption and degradation experiments was investigated. The degradation mechanism of MB upon treatment with MnO nanomixtures and H2O2 was studied and discussed. The results showed that a maximum adsorption capacity of 154 mg g−1 was obtained for a 60 mg L−1 MB solution at pH 9.0 and 25 °C, and the highest MB degradation ratio reached 99.8% under the following optimum conditions: 50 mL of MB solution (20 mg L−1) at room temperature and pH ≈ 8.0 with 7 mg of C, N-doped MnO and 0.5 mL of H2O2.

scholarly journals Influence of Cu(NO3)2 content used in thermal shock method on the photocatalytic activity of Cu-Modified ZnO nanoparticles

2021 ◽  
Vol 5 (3) ◽  
pp. first
Author(s):  
Thế Luân Nguyễn ◽  
Tiến Khoa Lê ◽  
Châu Ngọc Hoàng ◽  
Hữu Khánh Hưng Nguyễn ◽  
Thị Kiều Xuân Huỳnh
Keyword(s):  
Crystal Structure ◽  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Thermal Shock ◽  
Photoelectron Spectroscopy ◽  
Copper Content ◽  
Uv Light ◽  
Copper Nitrate ◽  
X Ray ◽  
Doped Zno

The Cu doped ZnO photocatalysts were prepared on ZnO substrate modified with copper nitrate by thermal shock method with different ratio % molar Cu : Zn = 0.3, 0.5, 1.0, 2.0 and 5.0 in order to study the impacts of copper content on the photocatalytic activity of ZnO under both UV and Vis light irradiation. The crystal structure, morphology bulk and surface were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activities were studied via time-dependent degradation of methylene blue in aqueous solution. The results exhibit that crystal structure and morphology of Cu doped ZnO photocatalysts is not modified significally than ZnO original but surface charateristicschanged greatly. The photocatalyst was doped with copper content under 2% showed formation of Cu species. These samples perform photocatalytic activity higher than ZnO. The CuNZO-0.05-500 had the highest rate constants for methylene blue degradation (kUV = 6,901 h-1, kVIS = 0,224 h-1), which are about 2.2 times and 1.3 times higher than unmodified ZnO under UV light and Vis light, respectively. However, the CuNZO-5.0-500 which had the formation of CuO phase and unchangeable ZnO's surface has photocatalytic activity similar to pure ZnO.

scholarly journals Effect of synthesis conditions  on  methylene blue adsorption capacity of electrochemically preparated graphene

2020 ◽  
Vol 9 (3) ◽  
pp. 9-14
Author(s):  
Hao Pham Van ◽  
Linh Ha Xuan ◽  
Oanh Phung Thi ◽  
Hong Phan Ngoc ◽  
Huy Nguyen Nhat ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Adsorption Capacity ◽  
Functional Groups ◽  
Photoelectron Spectroscopy ◽  
Graphene Nanosheets ◽  
Electrochemical Exfoliation ◽  
X Ray ◽  
Synthesis Conditions ◽  
Mb Adsorption

This report presents the effect of synthesis conditions on the synthesis of graphene nanosheets via electrochemical exfoliation method for adsorbing methylene blue from aqueous solution. Oxygen-containing functional groups and defects in the material were characterized by Raman and X-ray photoelectron spectroscopy (XPS). As a result, by using voltage of 15 V, (NH4)2SO4 (5%, 250 mL) and KOH (7.5%, 250 mL), the obtained material showed the highest MB adsorption capacity due to the high densities of oxygen-containing groups and defects comparison to other conditions.

Sign in / Sign up

Export Citation Format

Share Document