scholarly journals Friction and Wear Performance of Staple Carbon Fabric-Reinforced Composites: Effects of Surface Topography

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 141 ◽  
Author(s):  
Chang-Mou Wu ◽  
Yi-Ching Cheng ◽  
Wen-You Lai ◽  
Po-Hsun Chen ◽  
Tzong-Der Way
Keyword(s):  
Wear Rate ◽  
Surface Topography ◽  
Tribological Properties ◽  
Friction And Wear ◽  
Applied Pressure ◽  
Specific Wear Rate ◽  
Test Machine ◽  
Carbon Fabric ◽  
Sliding Speed ◽  
Resin Impregnation

Here, staple carbon fiber fabric-reinforced polycarbonate (PC)- and epoxy (EP)-based composites with different impregnating resin levels were fabricated using a modified film stacking process. The effects of surface topographies and resin types on the tribological properties of stable carbon fabric composites (sCFC) were investigated. Friction and wear tests on the carbon composites were conducted under unlubricated sliding using a disk-on-disk wear test machine. Experimental results showed that the coefficient of friction (COF) of the sCFC was dominated by matrix type, followed by peak material portion (Smr1) values, and finalized with core height (Sk) values. The COF of composites decreased by increasing the sliding speed and applied pressure. This also relied on surface topography and temperature generated at the worn surface. However, the specific wear rate was strongly affected by resin impregnation. Partially-impregnated composites showed lower specific wear rate, whereas fully-impregnated composites showed a higher wear rate. This substantially increased by increasing the sliding speed and applied pressure. Scanning electron microscopy observations of the worn surfaces revealed that the primary wear mechanisms were abrasion, adhesion, and fatigue for PC-based composites. For EP-based composites, this was primarily abrasion and fatigue. Results proved that partially-impregnated composites exhibited better tribological properties under severe conditions.

Effects of Elements Composition on Tribological Properties of PES/Metal Matrix Composite Materials

2013 ◽  
Vol 313-314 ◽  
pp. 188-192
Author(s):  
Zhi Gao Luo ◽  
Jin Li ◽  
Bing Zhao ◽  
Jian Wei Xu
Keyword(s):  
Composite Materials ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Tribological Properties ◽  
Metal Matrix ◽  
Friction And Wear ◽  
Plastic Layer ◽  
Test Machine

The friction and wear characteristics of PES/metal matrix composite materials were tested by the ball-disc friction pair of UMT-2 friction and wear test machine. The plastic layer is composed of distinct components. The results showed that: the tribological properties of PES/metal matrix composites were improved significantly after added 5wt % of the LCP. With the increasing of PTFE the PES/metal matrix composite material friction coefficient and wear rate were decreasing when the load of 10N and rotating speed of 400rmp. But the friction coefficient and wear rate increased when the mass fraction of PTFE more than 22 wt %. The tribological properties were the best when the PTFE content was 18 wt % to 25 wt % in the plastic layer.

The Mechanical Properties and Friction and Wear Behavior of C/C-SIC

2010 ◽  
Author(s):  
Gao Wen ◽  
Chongsheng Long ◽  
Tang Rui ◽  
Jiping Wang
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
Carbon Matrix ◽  
Specific Wear Rate ◽  
Sliding Speed ◽  
Wear Rates ◽  
Sic Composites

Carbon fiber reinforced carbon-silicon carbide composites (C/C-SiC) were prepared by chemical volume infiltration (CVI) method and reaction melt infiltration (RMI) technique of silicon liquid to carbon reinforce carbon matrix composites. The friction and wear behaviors of C/C-SiC composites at various loads and sliding speeds were investigated by MRH-3 block-on-ring tribometer at room temperature under water lubricating conditions. Furthermore, the morphologies, phase of the worn surface and the debris were observed, examined and analyzed by scanning electron microscopy (SEM) and energy-dispersive X-ray microanalysis (EDAX) respectively. Experimental results showed that the C/C-SiC composites had a better wear resistence, and the friction coefficient under water lubricated conditions is about 0.02–0.06. The influence of sliding speed on the friction coefficients and the specific wear rate of C/C-SiC is more obvious than that of normal load when the load is less than 200N (inclueded200N). The friction coefficient and the specific wear rate of C/C-SiC decreased as the sliding velocity increased. At the sliding speed higher than 2m/s, the friction coefficient is less than 0.02. The specific wear rates is at a low level about (2×10−7mm3/Nm–5×10−8mm3/Nm).

Optimization of tribological properties of aluminum hybrid composites using Taguchi design

2016 ◽  
Vol 51 (17) ◽  
pp. 2505-2515 ◽  
Author(s):  
Sandra Veličković ◽  
Blaža Stojanović ◽  
Miroslav Babić ◽  
Ilija Bobić
Keyword(s):  
Wear Rate ◽  
Tribological Properties ◽  
Hybrid Composites ◽  
Aluminum Matrix ◽  
Taguchi Design ◽  
Specific Wear Rate ◽  
Aluminum Matrix Composites ◽  
Sliding Speed ◽  
Weight Percentage ◽  
Sliding Distance

This paper analyses the influence of graphite reinforcement, load and sliding speed with constant sliding distance on tribological behavior of A356 aluminum matrix composites reinforced with 10 wt.% silicon carbide and graphite using the Taguchi design. Hybrid composites were produced in the compo-casting process. Tribological tests were performed on a block-on-disc tribometer where the weight percentage of graphite has three variations (0, 3, and 5), as well as load (10 N, 20 N, and 30 N) and sliding speed (0.25 m/s, 0.5 m/s, and 1 m/s), with sliding distance of 300 m. The wear of the composite is investigated under dry sliding condition. The specific wear rate was analyzed using Taguchi method with the aim of finding the optimal parameters. By applying analysis of variance, it was determined that the best tribological properties has A356/10SiC/3Gr hybrid composite. It was also found that the greatest impact on specific wear rate has load with the percentage effect of 69.163%, then sliding speed with 14.426% and the interaction between wt.% graphite and load. The dominant wear mechanism is adhesive wear as confirmed by scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS).

Experimental Study on Friction and Wear Behaviors of Ball Bearings under Gas Lubricated Conditions

2014 ◽  
Vol 66 (3) ◽  
Author(s):  
Mohd Fadzli Abdollah ◽  
Mohd Afiq Azfar Mazlan ◽  
Hilmi Amiruddin ◽  
Noreffendy Tamaldin
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Friction And Wear ◽  
Applied Load ◽  
Specific Wear Rate ◽  
Design Parameters ◽  
Ball Bearings ◽  
Sliding Speed ◽  
Air Lubrication ◽  
Sliding Distance

Friction and wear behaviors of ball bearings made from carbon-chrome steel were experimentally simulated using a modified ball-on-disc tribometer. The test was performed over a broad range of applied loads (W), sliding velocities (v) and sliding distances (L) under gas lubricated conditions using a Taguchi method. The results found that gas blown to the sliding surfaces in air effectively reduced the coefficient of friction as compared with the air lubrication at higher applied load, sliding speed and sliding distance. In addition, a specific wear rate is constant throughout the tests under gas lubricated conditions. However, under air lubrication, the specific wear rate decreases with increasing applied load, sliding speed and sliding distance. By using the optimal design parameters, a confirmation test successfully verify the N2-gas lubrication reduced average coefficient of friction and simultaneously improved wear resistance about 24% and 50%, respectively. This is in accordance with a significant reduction of wear scar diameter and smoother worn surface on a ball.

Friction and Wear of Potassium Titanate Whisker Filled Carbon Fabric/Phenolic Polymer Composites

2015 ◽  
Vol 137 (1) ◽  
Author(s):  
Xinrui Zhang ◽  
Xianqiang Pei ◽  
Qihua Wang ◽  
Tingmei Wang
Keyword(s):  
Wear Rate ◽  
Friction And Wear ◽  
Dip Coating ◽  
Hot Press ◽  
Carbon Fabric ◽  
Potassium Titanate ◽  
Transfer Films ◽  
Fabric Composites ◽  
Phenolic Polymer ◽  
Press Molding

Carbon fabric/phenolic composites modified with potassium titanate whisker (PTW) were prepared by a dip-coating and hot-press molding technique, and the tribological properties of the resulting composites were investigated systematically using a ring-on-block arrangement under different sliding conditions. Experimental results showed that the optimal PTW significantly decreased the wear-rate. The worn surfaces of the composites and the transfer film formed on the counterpart steel ring were examined by scanning electron microscopy (SEM) to reveal the wear mechanisms. The transfer films formed on the counterpart surfaces made contributions to the improvement of the tribological behavior of the carbon fabric composites. The friction and wear of the filled carbon fabric composites was significantly dependent on the sliding conditions. It is observed that the wear-rate increased with increasing applied load and sliding speeds.

Friction and Wear Behaviors of Solid Lubricants/Polyimide Composites in Liquid Mediums

2010 ◽  
Vol 654-656 ◽  
pp. 2763-2766 ◽  
Author(s):  
Li Wen Mu ◽  
Xin Feng ◽  
Yi Jun Shi ◽  
Huai Yuan Wang ◽  
Xiao Hua Lu
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Tribological Properties ◽  
Alkaline Solution ◽  
Dry Friction ◽  
Friction And Wear ◽  
Solid Lubricants ◽  
Polyimide Composites ◽  
Inorganic Fillers ◽  
Ptfe Composites

The tribological properties of polyimide (PI) composites reinforced with graphite or MoS2 sliding in liquid alkali and water as well as dry friction were investigated using a ring-on-ring tester. The results show that the friction coefficient (μ) and wear rate (W) for both graphite/PI and MoS2/PI composites in different liquid mediums are μdry>μwater >μalkali and Wwater>Wdry >Walkali. Results also indicate that the friction coefficient and wear rate of the PI composites filled with different solid lubricants are μMoS2 >μgraphite and W MoS2 >Wgraphite in different liquid mediums. In addition, the hydrophobic inorganic fillers are fit for the reinforcement of polymer-based composites sliding in liquid mediums. It is also concluded from the authors’ work that the wear rate and friction coefficient of polymer-based (such as PI, PTFE) composites in the alkali lubricated conditions is lowest among all the friction conditions. This may be attributed to the ionic hydration in the alkaline solution.

scholarly journals The tribological properties study of carbon fabric/ epoxy composites reinforced by nano-TiO2 and MWNTs

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 1127-1138 ◽  
Author(s):  
Fengjun Wei ◽  
Bingli Pan ◽  
Juan Lopez
Keyword(s):  
Tribological Properties ◽  
Friction And Wear ◽  
Epoxy Composite ◽  
Good Effect ◽  
Binder Phase ◽  
Carbon Fabric ◽  
Wear Properties ◽  
Brittle Rupture ◽  
Composites Materials ◽  
The Coefficient Of Friction

Abstract A kind of carbon fabric/epoxy composite was successfully prepared with carbon fiber fabric as reinforced phase and epoxy resin as binder phase, then the nano-TiO2 and a hybrid system of TiO2/MWNTs was added into the carbon fabric/ epoxy composite matrix respectively to prepare a kind of nano-composite. The friction and wear properties of CF/EP composites under different load conditions have been studied in this article, during the study the effects of filler types and contents on the tribological properties were researched, at last the worn surfaces were investigated and the abrasion mechanism was discussed. The results showed that: whether filling the nano-TiO2 alone or mixing the TiO2/MWNTs, it was able to achieve a good effect on decreasing friction and reducing wear, and the optimum addition ratio of the nano-TiO2 particles was 3.0% , meanwhile 3.0% of nano-TiO2 and 0.4% of MWNTs could cooperate with each other in their dimension, and could show a synergistic effect on modifying the tribological properties of CF/EP composites, the coefficient of friction of the modified composites decreased by 20% and the wear life increased by more than 140% compared with that of pristine composite materials, in the process of friction and wear, the wear form of the composites materials varied from brittle rupture to abrasive wear gradually.

scholarly journals Effect of Grain Size on the Friction-Induced Martensitic Transformation and Tribological Properties of 304 Austenite Stainless Steel

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1246
Author(s):  
Bo Mao ◽  
Shuangjie Chu ◽  
Shuyang Wang
Keyword(s):  
Grain Size ◽  
Stainless Steel ◽  
Martensitic Transformation ◽  
Wear Rate ◽  
Tribological Properties ◽  
Friction And Wear ◽  
Wear Behavior ◽  
304 Stainless Steel ◽  
Dry Sliding ◽  
Transformation Behavior

Friction and wear performance of austenite stainless steels have been extensively studied and show a close relationship with the friction-induced martensitic transformation. However, how the grain size and associated friction-induced martensitic transformation behavior affect the tribological properties of austenite steels have not been systematically studied. In this work, dry sliding tests were performed on an AISI 304 stainless steel with a grain size ranging from 25 to 92 μm. The friction-induced surface morphology and microstructure evolution were characterized. Friction-induced martensitic transformation behavior, including martensite nucleation, martensite growth and martensite variant selection and its effect on the friction and wear behavior of the 304 stainless steel were analyzed. The results showed that both the surface coefficient of friction (COF) and the wear rate increase with the grain size. The COF was reduced three times and wear rate was reduced by 30% as the grain size decreased from 92 to 25 μm. A possible mechanism is proposed to account for the effect of grain size on the tribological behavior. It is discussed that austenite steel with refined grain size tends to suppress the amount of friction-induced martensitic transformed and significantly alleviates both the plowing and adhesive effect during dry sliding.

scholarly journals Fabrication and Tribological Properties of Copper Matrix Solid Self-Lubricant Composites Reinforced with Ni/NbSe2 Composites

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1854
Author(s):  
Fei-xia Zhang ◽  
Yan-qiu Chu ◽  
Chang-sheng Li
Keyword(s):  
Powder Metallurgy ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Tribological Properties ◽  
Friction And Wear ◽  
Copper Matrix ◽  
Wear Properties ◽  
Disk Friction ◽  
Friction Reducing ◽  
Properties Of Composites

This paper presents a facile and effective method for preparing Ni/NbSe2 composites in order to improve the wettability of NbSe2 and copper matrix, which is helpful in enhancing the friction-reducing and anti-wear properties of copper-based composites. The powder metallurgy (P/M) technique was used to fabricate copper-based composites with different weight fractions of Ni/NbSe2, and tribological properties of composites were evaluated by using a ball-on-disk friction-and-wear tester. Results indicated that tribological properties of copper-based composites were improved by the addition of Ni/NbSe2. In particular, copper-based composites containing 15 wt.% Ni/NbSe2 showed the lowest friction coefficient (0.16) and wear rate (4.1 × 10−5 mm3·N−1·m−1) among all composites.

Widening Classical Wear Laws to the Concept of Third Body

2005 ◽  
Author(s):  
N. Fillot ◽  
I. Iordanoff ◽  
Y. Berthier
Keyword(s):  
Twentieth Century ◽  
Wear Rate ◽  
Applied Pressure ◽  
Third Body ◽  
Sliding Speed ◽  
Wear Law

During the second part of the twentieth century, many efforts have been done to model wear. Particularly, Archard proposes in 1953 [1] one of the first wear law, which is often written on the following form: dW/dt=K.P.V(1) with dW/dt the mass of detached particles from the rubbing materials per unit time, P the applied pressure, V the sliding speed and K the “wear rate”.

Sign in / Sign up

Export Citation Format

Share Document