scholarly journals A Method to Increase the Frequency Stability of a TCXO by Compensating Thermal Hysteresis

Sensors ◽  
2020 ◽  
Vol 20 (23) ◽  
pp. 6812
Author(s):  
Zhaoyang Wang ◽  
Jie Wu
Keyword(s):  
Thermal Hysteresis ◽  
Frequency Stability ◽  
Automotive Electronics ◽  
Frequency Compensation ◽  
Crystal Oscillator ◽  
Industrial Control ◽  
Temperature Changes ◽  
Measuring Devices ◽  
Different Temperatures ◽  
Crystal Oscillators

Due to the rapid growth of electronic information technology, the need for the higher stability of crystal oscillators has increased. The temperature-compensated X’tal (crystal) oscillator (TCXO), a type of crystal oscillator with high frequency stability, has been widely used in communications, sensor networks, automotive electronics, industrial control, measuring devices, and other equipment. The traditional TCXO only performs frequency compensation based on the current temperature, without considering the error caused by thermal hysteresis. As the frequency stability of the TCXO improves, the thermal hysteresis of the crystal oscillator has a negligible influence on the frequency stability of the crystal oscillator. This study measured different compensation tables for hysteresis curves at different temperatures and used a microprocessor to store the historical information of crystal temperature changes. Furthermore, corresponding algorithms were designed to select the correct values, according to the temperature change history, to compensate for the thermal hysteresis of the crystal oscillator error. Experiments show that this method can reduce the hysteresis error of the crystal oscillator from 700 to 150 ppb (−40 to 80 °C).

A New Application of Bimetallic Thin Film

2013 ◽  
Vol 661 ◽  
pp. 128-131
Author(s):  
Xiao Yu Yang ◽  
Wei Zhou
Keyword(s):  
Thin Film ◽  
Temperature Compensation ◽  
Fem Simulation ◽  
Frequency Stability ◽  
Crystal Plate ◽  
Crystal Oscillator ◽  
Temperature Changes ◽  
Thermal Expansion Coefficients ◽  
Element Simulation ◽  
Expansion Coefficients

To perform the temperature compensation, a bimetallic thin film with different thermal expansion coefficients is deposited on the surface of the crystal plate. The thermal stress generated in the crystal and the thin film will cancel each other when temperature changes, thus improve the frequency stability of the crystal oscillator. In this paper, a finite element simulation was carried out for the crystal plate with bimetal, and then an experiment was performed to verify the FEM simulation results. The result shows that this approach achieves good temperature - frequency characteristics and reduces the frequency shift of crystal oscillator.

Rolling Resistance Calculation Procedure Using the Finite Element Method

2019 ◽  
Vol 48 (3) ◽  
pp. 224-248
Author(s):  
Pablo N. Zitelli ◽  
Gabriel N. Curtosi ◽  
Jorge Kuster
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Rolling Resistance ◽  
Element Model ◽  
The Finite Element Method ◽  
Temperature Changes ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Materials Used ◽  
Account Temperature

ABSTRACT Tire engineers are interested in predicting rolling resistance using tools such as numerical simulation and tests. When a car is driven along, its tires are subjected to repeated deformation, leading to energy dissipation as heat. Each point of a loaded tire is deformed as the tire completes a revolution. Most energy dissipation comes from the cyclic loading of the tire, which causes the rolling resistance in addition to the friction force in the contact patch between the tire and road. Rolling resistance mainly depends on the dissipation of viscoelastic energy of the rubber materials used to manufacture the tires. To obtain a good rolling resistance, the calculation method of the tire finite element model must take into account temperature changes. It is mandatory to calibrate all of the rubber compounds of the tire at different temperatures and strain frequencies. Linear viscoelasticity is used to model the materials properties and is found to be a suitable approach to tackle energy dissipation due to hysteresis for rolling resistance calculation.

Preparation and Swelling Dynamics Characterization of Poly(N, N-Diethylacrylamide-Co-Itaconic Acid) Intelligent Hydrogels

2012 ◽  
Vol 490-495 ◽  
pp. 3382-3386
Author(s):  
Xiao Qi Li ◽  
Nai Yan Zhang ◽  
Jun Hai Zhang
Keyword(s):  
Itaconic Acid ◽  
Monomer Concentration ◽  
Molar Ratio ◽  
Solution Temperature ◽  
Temperature Changes ◽  
Different Temperatures ◽  
Total Monomer Concentration ◽  
Equilibrium Swelling Ratio ◽  
Composition Ratios ◽  
Response To Temperature

Poly(N,N-diethylacrylamide) (PDEA) hydrogel is known for their intelligent reversible swelling/deswelling behavior in response to temperature changes across a lower critical solution temperature (LCST) at around 31oC. In this study, itaconic acid (IA) was co-polymerized with N, N-diethylacrylamide (DEA) monomer to improve the swelling behavior and the total absorbing water. These copolymer hydrogels were prepared by changing the initial DEA/IA molar ratio and total monomer concentration. The chemical structure of hydrogels was characterized by fourier transform infrared (FTIR) spectroscopy. In comparison with the PDEA hydrogel, the equilibrium swelling ratio (ESR) of the hydrogels increase with the increase of IA content in the feed and the swelling dynamics behaviors of the different composition ratios of the P(DEA-co-IA) hydrogels on the different temperatures was investigated in detail.

scholarly journals Improving mechanical sensor performance through larger damping

Science ◽  
2018 ◽  
Vol 360 (6394) ◽  
pp. eaar5220 ◽  
Author(s):  
Swapan K. Roy ◽  
Vincent T. K. Sauer ◽  
Jocelyn N. Westwood-Bachman ◽  
Anandram Venkatasubramanian ◽  
Wayne K. Hiebert
Keyword(s):  
Quality Factor ◽  
High Performance ◽  
Signal To Noise Ratio ◽  
Frequency Stability ◽  
Crystal Oscillator ◽  
Sensor Performance ◽  
Atomic Force ◽  
Performance Metric ◽  
Mechanical Sensor ◽  
Oscillator Stability

Mechanical resonances are used in a wide variety of devices, from smartphone accelerometers to computer clocks and from wireless filters to atomic force microscopes. Frequency stability, a critical performance metric, is generally assumed to be tantamount to resonance quality factor (the inverse of the linewidth and of the damping). We show that the frequency stability of resonant nanomechanical sensors can be improved by lowering the quality factor. At high bandwidths, quality-factor reduction is completely mitigated by increases in signal-to-noise ratio. At low bandwidths, notably, increased damping leads to better stability and sensor resolution, with improvement proportional to damping. We confirm the findings by demonstrating temperature resolution of 60 microkelvin at 300-hertz bandwidth. These results open the door to high-performance ultrasensitive resonators in gaseous or liquid environments, single-cell nanocalorimetry, nanoscale gas chromatography, atmospheric-pressure nanoscale mass spectrometry, and new approaches in crystal oscillator stability.

scholarly journals Designing a Diving Protocol for Thermocline Identification Using Dive Computers in Marine Citizen Science

2018 ◽  
Vol 8 (11) ◽  
pp. 2315 ◽  
Author(s):  
Salih Egi ◽  
Pierre-Yves Cousteau ◽  
Massimo Pieri ◽  
Carlo Cerrano ◽  
Tamer Özyigit ◽  
...  
Keyword(s):  
Citizen Science ◽  
Second Phase ◽  
Temperature Changes ◽  
Scuba Divers ◽  
Science Projects ◽  
Specific Protocol ◽  
Accuracy And Precision ◽  
Different Temperatures ◽  
Central Database ◽  
Recreational Scuba

Dive computers have an important potential for citizen science projects where recreational SCUBA divers can upload the depth temperature profile and the geolocation of the dive to a central database which may provide useful information about the subsurface temperature of the oceans. However, their accuracy may not be adequate and needs to be evaluated. The aim of this study is to assess the accuracy and precision of dive computers and provide guidelines in order to enable their contribution to citizen science projects. Twenty-two dive computers were evaluated during real ocean dives for consistency and scatter in the first phase. In the second phase, the dive computers were immersed in sufficient depth to initiate the dive record inside a precisely controlled sea aquarium while using a calibrated device as a reference. Results indicate that the dive computers do not have the accuracy required for monitoring temperature changes in the oceans, however, they can be used to detect thermoclines if the users follow a specific protocol with specific dive computers. This study enabled the authors to define this protocol based on the results of immersion in two different sea aquarium tanks set to two different temperatures in order to simulate the conditions of a thermocline.

scholarly journals Effect of Heat Treatment Temperature on Martensitic Transformation and Superelasticity of the Ti49Ni51 Shape Memory Alloy

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2539 ◽  
Author(s):  
Peiyou Li ◽  
Yongshan Wang ◽  
Fanying Meng ◽  
Le Cao ◽  
Zhirong He
Keyword(s):  
Heat Treatment ◽  
Martensitic Transformation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Thermal Hysteresis ◽  
Treatment Temperature ◽  
Heat Treated ◽  
Different Temperatures ◽  
Tini Phase ◽  
Rapidly Solidified

The martensitic transformation and superelasticity of Ti49Ni51 shape memory alloy heat-treatment at different temperatures were investigated. The experimental results show that the microstructures of as-cast and heat-treated (723 K) Ni-rich Ti49Ni51 samples prepared by rapidly-solidified technology are composed of B2 TiNi phase, and Ti3Ni4 and Ti2Ni phases; the microstructures of heat-treated Ti49Ni51 samples at 773 and 823 K are composed of B2 TiNi phase, and of B2 TiNi and Ti2Ni phases, respectively. The martensitic transformation of as-cast Ti49Ni51 alloy is three-stage, A→R→M1 and R→M2 transformation during cooling, and two-stage, M→R→A transformation during heating. The transformations of the heat-treated Ti49Ni51 samples at 723 and 823 K are the A↔R↔M/A↔M transformation during cooling/heating, respectively. For the heat-treated alloy at 773 K, the transformations are the A→R/M→R→A during cooling/heating, respectively. For the heat-treated alloy at 773 K, only a small thermal hysteresis is suitable for sensor devices. The stable σmax values of 723 and 773 K heat-treated samples with a large Wd value exhibit high safety in application. The 773 and 823 K heat-treated samples have large stable strain–energy densities, and are a good superelastic alloy. The experimental data obtained provide a valuable reference for the industrial application of rapidly-solidified casting and heat-treated Ti49Ni51 alloy.

Continuous Tonic Spike Activity in Spider Warm Cells in the Absence of Sensory Input

2006 ◽  
Vol 96 (3) ◽  
pp. 989-997 ◽  
Author(s):  
E. Gingl ◽  
H. Tichy
Keyword(s):  
Electrical Stimulation ◽  
Sensory Input ◽  
Discharge Rate ◽  
Rate Of Change ◽  
Intrinsic Properties ◽  
Response Curves ◽  
Temperature Changes ◽  
Different Temperatures ◽  
Low Amplitude ◽  
The Relationship

The warm cells of the spider tarsal organ respond very sensitively to low-amplitude changes in temperature and discharge continuously as the rate of change in temperature reaches zero. To test whether the continuous tonic discharge remains without sensory input, we blocked the warm cell's receptive region by Epoxy glue. The activity continued in this situation, but its dependence on temperature changes was strongly reduced. We interpret this to mean that the warm cells exhibit specific intrinsic properties that underlie the generation of the tonic discharge. Experiments with electrical stimulation confirmed the observation that the warm cells persist in activity without an external drive. In warm cells with blocked receptive region, the response curves describing the relationship between the tonic discharge and the level of depolarization is the same for different temperatures. In warm cells with intact receptive region, the curves are shifted upward with rising temperature, as if the injected current is simply added to the receptor current. This indicates a modulating effect of the receptor current on the tonic discharge. Stimulation causes a change in the tonic discharge rate and thereby enables individual warm cells to signal the direction in addition to the magnitude of temperature changes.

Effects of SiO2 Particles in Mechanical Properties of Iron Composite

2013 ◽  
Vol 465-466 ◽  
pp. 886-890
Author(s):  
Adibah Amir ◽  
Othman Mamat
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Fine Particles ◽  
Sintering Temperature ◽  
Silica Particles ◽  
Milling Process ◽  
Powder Metallurgy Technique ◽  
Temperature Changes ◽  
Different Temperatures

Tronohs raw sand was converted into fine silica particles via a series of milling process. Addition of these fine particles into iron composite was found to modify its mechanical properties. The composite was prepared using powder metallurgy technique with varying percentage of silica particles; 5, 10, 15, 20 and 25wt%. The composites were sintered at three different temperatures; 1000° C, 1100° C and 1200° C to find the most suitable sintering temperature. Changes in density and hardness were observed. The results showed that composite consist of 20wt% silica particles and sintered at 1100° C exhibits best improvement.

Sign in / Sign up

Export Citation Format

Share Document