scholarly journals Optimization of Inlet and Exhaust Manifold on a Single Cylinder Diesel Engine to Enhance the Combustion

2019 ◽  
Vol 8 (10) ◽  
pp. 1408-1411
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Fuel Mixture ◽  
Exhaust Valve ◽  
Intake Manifold ◽  
Power Stroke ◽  
Depth Of Cut ◽  
Exhaust Manifold ◽  
Single Cylinder

In the internal combustion Diesel engines the most important subsystem is Intake manifold and Exhaust manifold. In the intake manifold which supplies fresh air –fuel mixture in to the cylinders where combustion takes place at high temperature and high pressure. After exhaust gases scavenged through valves from the cylinders, these gases past exhaust manifold an outlet, through which the gases flow into exhaust pipes from there to the emission control equipment of engine which consists of catalytic and thermal converters. The development of swirl can be enhanced by re-designing of inlet port of an Engine. There is further development in the swirl due to combustion process to another maximum part way in to the power stroke. Swirl can promotes the combustion process in a better way and causes efficiency increase. Better mixing of air – fuel there is a little bit changing the inlet and exhaust valve. Valve stem diameter is 9.5mm, Inlet valve diameter is 36mm, Exhaust Valve diameter is 28mm by varying the pitch 1.0mm to 2mm and thread depth of cut as 4mm and three thread per inch from this arrangement to investigate the performance by enhancing the swirl of air flow to get betterment in the performance and decrease in emissions in a (DI) direct injection diesel engine with single cylinder when compared with normal engine.

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

CFD Modelling of the Effects of Injection Timing on the Combustion Process and Emissions in an HSDI Diesel Engine

2012 ◽  
Author(s):  
Raouf Mobasheri ◽  
Zhijun Peng
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Cfd Simulation ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Cfd Modelling ◽  
Combustion Modeling ◽  
Pressure Trace ◽  
Hsdi Diesel Engine

High-Speed Direct Injection (HSDI) diesel engines are increasingly used in automotive applications due to superior fuel economy. An advanced CFD simulation has been carried out to analyze the effect of injection timing on combustion process and emission characteristics in a four valves 2.0L Ford diesel engine. The calculation was performed from intake valve closing (IVC) to exhaust valve opening (EVO) at constant speed of 1600 rpm. Since the work was concentrated on the spray injection, mixture formation and combustion process, only a 60° sector mesh was employed for the calculations. For combustion modeling, an improved version of the Coherent Flame Model (ECFM-3Z) has been applied accompanied with advanced models for emission modeling. The results of simulation were compared against experimental data. Good agreement of calculated and measured in-cylinder pressure trace and pollutant formation trends were observed for all investigated operating points. In addition, the results showed that the current CFD model can be applied as a beneficial tool for analyzing the parameters of the diesel combustion under HSDI operating condition.

Explorative Investigation on Cashew Nut Shell Liquid Biodiesel blended with Ethanol and Hydrogen in Direct Injection (DI) Diesel Engine and prediction through Artificial Neural Network

2021 ◽  
Author(s):  
Thanigaivelan V ◽  
Lavanya R
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Cashew Nut Shell Liquid ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Cashew Nut ◽  
Di Diesel Engine ◽  
Artificial Neural ◽  
Cashew Nut Shell

Abstract Emission from the DI diesel engine is series setback for environment viewpoint. Intended for that investigates for alternative biofuel is persuaded. The important hitches with the utilization of biofuels and their blends in DI diesel engines are higher emanations and inferior brake-thermal efficiency as associated to sole diesel fuel. In this effort, Cashew nut shell liquid (CNSL) biodiesel, hydrogen and ethanol (BHE) mixtures remained verified in a direct-injection diesel engine with single cylinder to examine the performance and discharge features of the engine. The ethanol remained supplemented 5%, 10% and 15% correspondingly through enhanced CNSL as well as hydrogen functioned twin fuel engine. The experiments done in a direct injection diesel engine with single-cylinder at steadystate conditions above the persistent RPM (1500RPM). Throughout the experiment, emissions of pollutants such as fuel consumption rate (SFC), hydrocarbons (HC), carbon monoxide (CO), nitrogen oxides (NOx) and pressure of the fuel were also measured. cylinders. The experimental results show that, compared to diesel fuel, the braking heat of the biodiesel mixture is reduced by 26.79-24% and the BSFC diminutions with growing addition of ethanol from the CNSL hydrogen mixture. The BTE upsurges thru a rise in ethanol proportion with CNSL hydrogen mixtures. Finally, the optimum combination of ethanol with CNSL hydrogen blends led to the reduced levels of HC and CO emissions with trivial upsurge in exhaust gas temperature and NOx emissions. This paper reconnoiters the routine of artificial neural networks (ANN) to envisage recital, ignition and discharges effect.

Simulation of a Single Cylinder Diesel Engine Under Cold Start Conditions Using Simulink

2000 ◽  
Vol 123 (1) ◽  
pp. 117-124 ◽  
Author(s):  
H.-Q. Liu ◽  
N. G. Chalhoub ◽  
N. Henein
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Cold Start ◽  
Operating Conditions ◽  
Combustion Model ◽  
Nonlinear Dynamic Model ◽  
Single Cylinder ◽  
Engine Model ◽  
Simulink Model ◽  
Engine Components

A nonlinear dynamic model is developed in this study to simulate the overall performance of a naturally aspirated, single cylinder, four-stroke, direct injection diesel engine under cold start and fully warmed-up conditions. The model considers the filling and emptying processes of the cylinder, blowby, intake, and exhaust manifolds. A single zone combustion model is implemented and the heat transfer in the cylinder, intake, and exhaust manifolds are accounted for. Moreover, the derivations include the dynamics of the crank-slider mechanism and employ an empirical model to estimate the instantaneous frictional losses in different engine components. The formulation is coded in modular form whereby each module, which represents a single process in the engine, is introduced as a single block in an overall Simulink engine model. The numerical accuracy of the Simulink model is verified by comparing its results to those generated by integrating the engine formulation using IMSL stiff integration routines. The engine model is validated by the close match between the predicted and measured cylinder gas pressure and engine instantaneous speed under motoring, steady-state, and transient cold start operating conditions.

Effects of the Injection Parameters on the Emissions of a Heavy Duty Diesel Engine

2009 ◽  
Author(s):  
M. Yılmaz ◽  
M. Zafer Gul ◽  
Y. Yukselenturk ◽  
B. Akay ◽  
H. Koten
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Design Parameters ◽  
Combustion Model ◽  
Particulate Emissions ◽  
Multiphase Model ◽  
Heavy Duty ◽  
Flow Development ◽  
Air Motion

It is estimated by the experts in the automotive industry that diesel engines on the transport market should increase within the years to come due to their high thermal efficiency coupled with low carbon dioxide (CO2) emissions, provided their nitrogen oxides (NOx) and particulate emissions are reduced. At present, adequate after-treatments, NOx and particulates matter (PM) traps are developed and industrialized with still concerns about fuel economy, robustness, sensitivity to fuel sulfur and cost because of their complex and sophisticated control strategy. New combustion processes focused on clean diesel combustion are investigated for their potential to achieve near zero particulate and NOx emissions. Their main drawbacks are increased level of unburned hydrocarbons (HC) and carbon monoxide (CO) emissions, combustion control at high load and limited operating range and power output. In this work, cold flow simulations for a single cylinder of a nine-liter (6 cylinder × 1.5 lt.) diesel engine have been performed to find out flow development and turbulence generation in the piston-cylinder assembly. In this study, the goal is to understand the flow field and the combustion process in order to be able to suggest some improvements on the in-cylinder design of an engine. Therefore combustion simulations of the engine have been performed to find out flow development and emission generation in the cylinder. Moreover, the interaction of air motion with high-pressure fuel spray injected directly into the cylinder has also been carried out. A Lagrangian multiphase model has been applied to the in-cylinder spray-air motion interaction in a heavy-duty CI engine under direct injection conditions. A comprehensive model for atomization of liquid sprays under high injection pressures has been employed. The combustion is modeled via a new combustion model ECFM-3Z (Extended Coherent Flame Model) developed at IFP. Finally, a calculation on an engine configuration with compression, spray injection and combustion in a direct injection Diesel engine is presented. Further investigation has also been performed in-cylinder design parameters in a DI diesel engine that result in low emissions by effect of high turbulence level. The results are widely in agreement qualitatively with the previous experimental and computational studies in the literature.

Engine Analysis of Single Cylinder DI Diesel Engine Fuelled With Sunflower Oil, Sunflower Oil Methyl Ester and Its Blends

2006 ◽  
Author(s):  
V. Anandram ◽  
S. Ramakrishnan ◽  
J. Karthick ◽  
S. Saravanan ◽  
G. LakshmiNarayanaRao
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Sunflower Oil ◽  
Direct Injection ◽  
Emission Characteristics ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Di Diesel Engine ◽  
Engine Emission ◽  
Oil Sunflower

In the present work, the combustion, performance and emission characteristics of sunflower oil, sunflower methyl ester and its blends were studied and compared with diesel by employing them as fuel in a single cylinder, direct injection, 4.4 KW, air cooled diesel engine. Emission measurements were carried out using five-gas exhaust gas analyzer and smoke meter. The performance characteristics of Sunflower oil, Sunflower methyl ester and its blends were comparable with those of diesel. The components of exhaust such as HC, CO, NOx and soot concentration of the fuels were measured and presented as a function of load and it was observed that the blends had similar performance and emission characteristics as those of diesel. NOx emissions of sunflower oil methyl ester were slightly higher than that of diesel but that of sunflower oil was slightly lower than that of diesel. With respect to the combustion characteristics it was found that the biofuels have lower ignition delay than diesel. The heat release rate was very high for diesel than for the biofuel.

Study on Altitude Adaptability of a Turbocharged Off-Road Diesel Engine

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Fenlian Huang ◽  
Jilin Lei ◽  
Qianfan Xin
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Spray Angle ◽  
Fuel Spray ◽  
Intake Manifold ◽  
Bench Test ◽  
Boost Pressure ◽  
Exhaust Manifold ◽  
Power Performance ◽  
Operating Characteristics

Abstract This paper investigates the operating characteristics of an off-road diesel engine to enhance its power performance in plateau. First, the impacts of altitude on the power, fuel economy, and emissions characteristics were analyzed by a bench test. Second, the combustion and overall performance working at different altitudes were studied by three-dimensional numerical simulation, including the relationship between fuel injection parameters and engine performance. The results showed that altitude significantly affects the performance of the off-road diesel engine. As the altitude increased from 0 m to 2000 m, the engine power decreased as much as 4.3%, and the brake-specific fuel consumption (BSFC) increased as much as 6%. At the peak torque condition, the intake manifold boost pressure and the exhaust manifold pressure both reduced with a rise of altitude, while the intake and exhaust manifold temperatures both increased with a rise of altitude. Finally, after comparing the in-cylinder flow conditions and combustion characteristics given by six combustion chamber designs that have different shrinkage ratios, the engine performance at 4000 m altitude with five different fuel spray angles were further optimized. The engine rated power increased by 8.2% when the shrinkage ratio was 7.28% and the fuel spray angle was 150 deg at the 4000 m altitude.

scholarly journals Experimental study of multiple pilot injection strategy in an automotive direct injection diesel engine

2018 ◽  
Vol 234 ◽  
pp. 03007
Author(s):  
Plamen Punov ◽  
Tsvetomir Gechev ◽  
Svetoslav Mihalkov ◽  
Pierre Podevin ◽  
Dalibor Barta
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Pilot Injection ◽  
Injection Strategy ◽  
Direct Injection Diesel Engine ◽  
Rate Of Heat Release

The pilot injection strategy is a widely used approach for reducing the noise of the combustion process in direct injection diesel engines. In the last generation of automotive diesel engines up to several pilot injections could occur to better control the rate of heat release (ROHR) in the cylinder as well as the pollutant formation. However, determination of the timing and duration for each pilot injection needs to be precisely optimised. In this paper an experimental study of the pilot injection strategy was conducted on a direct injection diesel engine. Single and double pilot injection strategy was studied. The engine rated power is 100 kW at 4000 rpm while the rated torque is 320 Nm at 2000 rpm. An engine operating point determined by the rotation speed of 1400 rpm and torque of 100 Nm was chosen. The pilot and pre-injection timing was widely varied in order to study the influence on the combustion process as well as on the fuel consumption.

Sign in / Sign up

Export Citation Format

Share Document