scholarly journals DESIGN AND ANALYSIS OF LOW-POWER, HIGH-SPEED BAUGH WOOLEY MULTIPLIER

2019 ◽  
Vol 2019 (02) ◽  
pp. 60-70
Author(s):  
Karuppusamy P
Keyword(s):  
Performance Analysis ◽  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Paper Analysis ◽  
The Other ◽  
Very High

The fundamental operations of the communication are the multiplication and division. The multiplier usually consumes a larger area and power and poses a very high latency. As all the above mentioned characteristics of the multiplier depends on the techniques utilized for the multiplication. It becomes necessary to put into effect a proper multiplier that reduces both the latency and the power consumption. So the paper analysis the performance of the various multipliers and scopes to develop a low power high speed multiplier based on the Baugh Wooley algorithm. The Performance analysis of the Baugh Wooley multiplier and the other existing multipliers is done and was found that the performance of the Baugh Wooley in terms of the latency and the power consumption was convincing compared to the other existing methods.

scholarly journals Design and analysis of Low Power High Speed Pulse Triggered Flip Flop

2016 ◽  
Vol 5 (03) ◽  
pp. 01-06
Author(s):  
Mr. Kankan Sarkar
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
The Other ◽  
Discharge Time ◽  
Flip Flop ◽  
Power Pulse

The main important aspect is to outline a high speed and utilization of low power pulse triggered flip-flop and simulate the same. Also, we have to minimize leakage in the consumption of power in a flip-flop by employing pulse triggering technique that is adopted for clocks. Here, to solve the problem in the discharging path of the similar flip flop implementations, we employ signal feed through technique. The discharge time is reduced by the proposed method. This design out performs all the other similar pulse triggered flip flop implementation both in speed and power consumption. Now, it is implemented by employing Cadence Virtuoso Schematic Composer in 90nm GPDK. Simulation is done by a simulator known as Spectre.

Design and Implementation of an Efficient Parallel LFSR Architecture for Wireless Communication Systems

2019 ◽  
Vol 14 ◽  
Author(s):  
A. Suresh Babu ◽  
B. Anand
Keyword(s):  
Wireless Communication ◽  
Power Consumption ◽  
Low Power ◽  
Communication Systems ◽  
High Speed ◽  
Design Tool ◽  
Shift Register ◽  
Linear Feedback ◽  
Wireless Communication Systems ◽  
Coverage Area

: A Linear Feedback Shift Register (LFSR) considers a linear function typically an XOR operation of the previous state as an input to the current state. This paper describes in detail the recent Wireless Communication Systems (WCS) and techniques related to LFSR. Cryptographic methods and reconfigurable computing are two different applications used in the proposed shift register with improved speed and decreased power consumption. Comparing with the existing individual applications, the proposed shift register obtained >15 to <=45% of decreased power consumption with 30% of reduced coverage area. Hence this proposed low power high speed LFSR design suits for various low power high speed applications, for example wireless communication. The entire design architecture is simulated and verified in VHDL language. To synthesis a standard cell library of 0.7um CMOS is used. A custom design tool has been developed for measuring the power. From the results, it is obtained that the cryptographic efficiency is improved regarding time and complexity comparing with the existing algorithms. Hence, the proposed LFSR architecture can be used for any wireless applications due to parallel processing, multiple access and cryptographic methods.

Low Power and High Speed Sequential Circuits Test Architecture

2019 ◽  
Vol 12 ◽  
Author(s):  
Ahmed K. Jameil ◽  
Yasir Amer Abbas ◽  
Saad Al-Azawi
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Test Generation ◽  
High Speed ◽  
Fir Filter ◽  
Sequential Circuits ◽  
Fir Filters ◽  
Design Verification ◽  
Sequential Circuit ◽  
Generation Algorithm

Background: The designed circuits are tested for faults detection in fabrication to determine which devices are defective. The design verification is performed to ensure that the circuit performs the required functions after manufacturing. Design verification is regarded as a test form in both sequential and combinational circuits. The analysis of sequential circuits test is more difficult than in the combinational circuit test. However, algorithms can be used to test any type of sequential circuit regardless of its composition. An important sequential circuit is the finite impulse response (FIR) filters that are widely used in digital signal processing applications. Objective: This paper presented a new design under test (DUT) algorithm for 4-and 8-tap FIR filters. Also, the FIR filter and the proposed DUT algorithm is implemented using field programmable gate arrays (FPGA). Method: The proposed test generation algorithm is implemented in VHDL using Xilinx ISE V14.5 design suite and verified by simulation. The test generation algorithm used FIR filtering redundant faults to obtain a set of target faults for DUT. The fault simulation is used in DUT to assess the benefit of test pattern in fault coverage. Results: The proposed technique provides average reductions of 20 % and 38.8 % in time delay with 57.39 % and 75 % reductions in power consumption and 28.89 % and 28.89 % slices reductions for 4- and 8-tap FIR filter, respectively compared to similar techniques. Conclusions: The results of implementation proved that a high speed and low power consumption design can be achieved. Further, the speed of the proposed architecture is faster than that of existing techniques.

scholarly journals Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Nanophotonics ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 937-945
Author(s):  
Ruihuan Zhang ◽  
Yu He ◽  
Yong Zhang ◽  
Shaohua An ◽  
Qingming Zhu ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
High Performance ◽  
Pulse Amplitude ◽  
Telecommunication Networks ◽  
Low Power Consumption ◽  
Power Efficient ◽  
High Speed Data ◽  
On Chip

AbstractUltracompact and low-power-consumption optical switches are desired for high-performance telecommunication networks and data centers. Here, we demonstrate an on-chip power-efficient 2 × 2 thermo-optic switch unit by using a suspended photonic crystal nanobeam structure. A submilliwatt switching power of 0.15 mW is obtained with a tuning efficiency of 7.71 nm/mW in a compact footprint of 60 μm × 16 μm. The bandwidth of the switch is properly designed for a four-level pulse amplitude modulation signal with a 124 Gb/s raw data rate. To the best of our knowledge, the proposed switch is the most power-efficient resonator-based thermo-optic switch unit with the highest tuning efficiency and data ever reported.

scholarly journals A Low-Power 12-Bit 20 MS/s Asynchronously Controlled SAR ADC for WAVE ITS Sensor Based Applications

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2260
Author(s):  
Khuram Shehzad ◽  
Deeksha Verma ◽  
Danial Khan ◽  
Qurat Ul Ain ◽  
Muhammad Basim ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Intelligent Transportation System ◽  
Cmos Process ◽  
Process Technology ◽  
Back Issue ◽  
Digital To Analog Converter ◽  
Analog To Digital ◽  
Switching Method

A low power 12-bit, 20 MS/s asynchronously controlled successive approximation register (SAR) analog-to-digital converter (ADC) to be used in wireless access for vehicular environment (WAVE) intelligent transportation system (ITS) sensor based application is presented in this paper. To optimize the architecture with respect to power consumption and performance, several techniques are proposed. A switching method which employs the common mode charge recovery (CMCR) switching process is presented for capacitive digital-to-analog converter (CDAC) part to lower the switching energy. The switching technique proposed in our work consumes 56.3% less energy in comparison with conventional CMCR switching method. For high speed operation with low power consumption and to overcome the kick back issue in the comparator part, a mutated dynamic-latch comparator with cascode is implemented. In addition, to optimize the flexibility relating to the performance of logic part, an asynchronous topology is employed. The structure is fabricated in 65 nm CMOS process technology with an active area of 0.14 mm2. With a sampling frequency of 20 MS/s, the proposed architecture attains signal-to-noise distortion ratio (SNDR) of 65.44 dB at Nyquist frequency while consuming only 472.2 µW with 1 V power supply.

A LOW-POWER AND HIGH-SPEED D FLIP-FLOP USING A SINGLE LATCH

2002 ◽  
Vol 11 (01) ◽  
pp. 51-55
Author(s):  
ROBERT C. CHANG ◽  
L.-C. HSU ◽  
M.-C. SUN
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Power Dissipation ◽  
High Speed ◽  
Operating Frequency ◽  
Flip Flop ◽  
Lower Power ◽  
Simulation Results ◽  
Hspice Simulation

A novel low-power and high-speed D flip-flop is presented in this letter. The flip-flop consists of a single low-power latch, which is controlled by a positive narrow pulse. Hence, fewer transistors are used and lower power consumption is achieved. HSPICE simulation results show that power dissipation of the proposed D flip-flop has been reduced up to 76%. The operating frequency of the flip-flop is also greatly increased.

scholarly journals A high-speed hybrid Full Adder with low power consumption

2012 ◽  
Vol 9 (24) ◽  
pp. 1900-1905
Author(s):  
Kamran Delfan Hemmati ◽  
Mojtaba Behzad Fallahpour ◽  
Abbas Golmakani ◽  
Kamyar Delfan Hemmati
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Full Adder ◽  
Low Power Consumption

scholarly journals A HIGH-PERFORMANCE AND LOW-POWER DELAY BUFFER

2013 ◽  
pp. 78-82
Author(s):  
GOPALA KRISHNA.M ◽  
UMA SANKAR.CH ◽  
NEELIMA. S ◽  
KOTESWARA RAO.P
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
High Performance ◽  
Vlsi Design ◽  
Flip Flop ◽  
Ring Counter ◽  
Double Edge ◽  
Low Power Cmos ◽  
Cmos Vlsi

In this paper, presents circuit design of a low-power delay buffer. The proposed delay buffer uses several new techniques to reduce its power consumption. Since delay buffers are accessed sequentially, it adopts a ring-counter addressing scheme. In the ring counter, double-edge-triggered (DET) flip-flops are utilized to reduce the operating frequency by half and the C-element gated-clock strategy is proposed. Both total transistor count and the number of clocked transistors are significantly reduced to improve power consumption and speed in the flip-flop. The number of transistors is reduced by 56%-60% and the Area-Speed-Power product is reduced by 56%-63% compared to other double edge triggered flip-flops. This design is suitable for high-speed, low-power CMOS VLSI design applications.

scholarly journals Novel Design of Low-Power High-Speed Hybrid Full Adder Design using Gate Diffusion Input (GDI) Technique

2020 ◽  
Vol 9 (12) ◽  
pp. 323-328
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Critical Path ◽  
Circuit Simulation ◽  
Full Adder ◽  
Cmos Process ◽  
Path Delay ◽  
Process Technology ◽  
Xnor Gate

VLSI technology become one of the most significant and demandable because of the characteristics like device portability, device size, large amount of features, expenditure, consistency, rapidity and many others. Multipliers and Adders place an important role in various digital systems such as computers, process controllers and signal processors in order to achieve high speed and low power. Two input XOR/XNOR gate and 2:1 multiplexer modules are used to design the Hybrid Full adders. The XOR/XNOR gate is the key punter of power included in the Full adder cell. However this circuit increases the delay, area and critical path delay. Hence, the optimum design of the XOR/XNOR is required to reduce the power consumption of the Full adder Cell. So a 6 New Hybrid Full adder circuits are proposed based on the Novel Full-Swing XOR/XNOR gates and a New Gate Diffusion Input (GDI) design of Full adder with high-swing outputs. The speed, power consumption, power delay product and driving capability are the merits of the each proposed circuits. This circuit simulation was carried used cadence virtuoso EDA tool. The simulation results based on the 90nm CMOS process technology model.

Sign in / Sign up

Export Citation Format

Share Document