scholarly journals PERFORMANCE AND EXHAUST EMISSIONS OF DIRECT‐INJECTION DIESEL ENGINE OPERATING ON RAPESEED OIL AND ITS BLENDS WITH DIESEL FUEL

Transport ◽  
2005 ◽  
Vol 20 (5) ◽  
pp. 186-194 ◽  
Author(s):  
Gvidonas Labeckas ◽  
Stasys Slavinskas
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Brake Specific Fuel Consumption ◽  
Fuel Blend ◽  
Engine Operation ◽  
Point Increase ◽  
Smoke Opacity ◽  
Co Emission

During engine operation at 1 400, 1 800 and 2 200 min‐1 the brake specific fuel consumption has on an average been increased by 0,104 %, 0,134 % and 0,156 % for every 1 % point increase in RO inclusion into DF. The maximum thermal efficiency values remain within 0,37–0,39 intervals. The maximum NOx emission increases with the mass percent of oxygen in the fuel blend and for RO and its blends RO75 and RO50 are higher by 9,2 %, 20,7 % and 5,1 %, respectively. Emissions of NO2 increase with an increasing content of RO premixed into DF. When operating on pure RO and its blends RO75 and RO50 the maximum CO emission reduces by 40,5 % ‐52,9 % and 7,2 %‐15,0 %, respectively. The smoke opacity generated from RO and its blends is also by 27,1% ‐34,6 % and 41,7 % ‐51,0 % lower. Emissions of HC remain on a considerably low level ranging between 8 to 16 ppm whereas during engine operation on pure RO they approach to about a zero level. Emissions of CO2 for RO and fuel blend RO75 are slightly higher.

THE EFFECT OF ETHANOL, PETROL AND RAPESEED OIL BLENDS ON DIRECT INJECTION DIESEL ENGINE PERFORMANCE AND EXHAUST EMISSIONS

Transport ◽  
2010 ◽  
Vol 25 (2) ◽  
pp. 116-128 ◽  
Author(s):  
Gvidonas Labeckas ◽  
Stasys Slavinskas
Keyword(s):  
Carbon Monoxide ◽  
Diesel Engine ◽  
Thermal Efficiency ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Engine Performance ◽  
Maximum Torque ◽  
Brake Thermal Efficiency ◽  
Brake Mean Effective Pressure ◽  
Smoke Opacity

The article deals with the testing results of a four stroke four cylinder, DI diesel engine operating on pure rapeseed oil (RO) and its 2.5vol%, 5vol% and 7.5vol% blends with ethanol (ERO) and petrol (PRO). The purpose of this study is to examine the effect of ethanol and petrol addition to RO on blend viscosity, percentage changes in brake mean effective pressure (bmep), brake specific fuel consumption (bsfc), the brake thermal efficiency (çe) of a diesel engine and its emission composition, including NO, NO2, NOX, CO, CO2, HC and the smoke opacity of exhausts. The addition of 2.5, 5 and 7.5vol% of ethanol and the same percentage of petrol into RO, at a temperature of 20 °C, diminish the viscosity of the blends by 9.2%, 21.3%, 28.3% and 14.1%, 24.8%, 31.7% respectively. Heating biofuels up to a temperature of 60 °C, diminishes the kinematic viscosity of RO, blends ERO2.5–7.5 and PRO2.5–7.5 4.2, 3.9–3.8 and 3.9–3.7 times accordingly. At a speed of 1400–1800 min‐1, bmep higher by 1.3% if compared with that of RO (0.772–0.770 MPa) ensures blend PRO2.5, whereas at a rated speed of 2200 min‐1 , bmep higher by 5.6–2.7% can be obtained when fuelling the loaded engine, ë = 1.6, with both PRO2.5–5 blends. The bsfc of the engine operating on blend PRO2.5 at maximum torque and rated power is respectively 3.0% and 5.5% lower. The highest brake thermal efficiency at maximum torque (0.400) and rated power (0.415) compared to that of RO (0.394) also suggests blend PRO2.5. The largest increase in NOXemissions making 1907 ppm (24.8%) and 1811 ppm (19.6%) compared to that of RO was measured from a more calorific blend PRO7.5 (9.99% oxygen) at low (1400 min‐1) and rated (2200 min‐1) speeds. The emission of carbon monoxide from blends ERO2.5–5 throughout the whole speed range runs lower from 6.1% to 32.9% and the smoke opacity of the fully loaded engine changes from 5.1% which is a higher to 46.4% which is a lower level if compared to the corresponding data obtained using pure RO. The CO2 emissions of carbon monoxide and the temperature of the exhausts generated by the engine running at a speed of 2200 min‐1 diminish from 7.8 vol% to 6.3vol% and from 500 °C to 465 °C due to the addition of 7.5vol% of ethanol to RO.

scholarly journals Performance and emissions of a single cylinder diesel engine operating with rapeseed oil and jp-8 fuel blends

2015 ◽  
Vol 162 (3) ◽  
pp. 13-18
Author(s):  
Gvidonas Labeckas ◽  
Irena Kanapkienė
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Rapeseed Oil ◽  
Jet Fuel ◽  
Brake Specific Fuel Consumption ◽  
Test Results ◽  
Brake Thermal Efficiency ◽  
Engine Load ◽  
Fuel Blends

The article presents experimental test results of a DI single-cylinder, air-cooled diesel engine FL 511 operating with the normal (class 2) diesel fuel (DF), rapeseed oil (RO) and its 10%, 20% and 30% (v/v) blends with aviation-turbine fuel JP-8 (NATO code F-34). The purpose of the research was to analyse the effects of using various rapeseed oil and jet fuel RO90, RO80 and RO70 blends on brake specific fuel consumption, brake thermal efficiency, emissions and smoke of the exhaust. The test results of engine operation with various rapeseed oil and jet fuel blends compared with the respective parameters obtained when operating with neat rapeseed oil and those a straight diesel develops at full (100%) engine load and maximum brake torque speed of 2000 rpm. The research results showed that jet fuel added to rapeseed oil allows to decrease the value of kinematic viscosity making such blends suitable for the diesel engines. Using of rapeseed oil and jet fuel blends proved themselves as an effective measure to maintain fuel-efficient performance of a DI diesel engine. The brake specific fuel consumption decreased by about 6.1% (313.4 g/kW·h) and brake thermal efficiency increase by nearly 1.0% (0.296) compared with the respective values a fully (100%) loaded engine fuelled with pure RO at the same test conditions. The maximum NOx emission was up to 13.7% higher, but the CO emissions and smoke opacity of the exhaust 50.0% and 3.4% lower, respectively, for the engine powered with biofuel blend RO70 compared with those values produced by the combustion of neat rapeseed oil at full (100%) engine load and speed of 2000 rpm.

Effects of Ethanol-n butanol-diesel Oxygenated Fuel on Performance of Diesel Engine

2013 ◽  
Vol 860-863 ◽  
pp. 1766-1769
Author(s):  
Ming Wei Xiao ◽  
Jin'ge He
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Brake Specific Fuel Consumption ◽  
Fuel Supply ◽  
Direct Injection Diesel Engine ◽  
Oxygenated Fuel ◽  
Performance And Emissions ◽  
Blend Fuel

The experiments of the economy performance and emissions of diesel engine fueled with ethanol-n butanol-diesel were performed on a dual-cylinder direct injection diesel engine. The results show that without modification on the engine, while the mixed proportion of ethanol getting larger, the equivalent brake specific fuel consumption decreases and effective thermal efficiency increases when the diesel engine work on medium and high loads condition, NOX emissions and smoke decreased obviously. But the smoke increased when the proportion of ethanol is 20%. And the results also indicate that it is beneficial for decreasing the smoke and NOX emissions to reduce suitably fuel supply advance angle when the diesel engine fueled with blend fuel mixed high proportion of ethanol.

scholarly journals PERFORMANCE AND EMISSIONS OF A DIESEL ENGINE OPERATING WITH RENEWABLE BINARY BIODIESEL-N-BUTANOL BIOFUEL BLENDS

2020 ◽  
Vol 1 (14) ◽  
pp. 17-25
Author(s):  
Gvidonas LABECKAS ◽  
Stasys SLAVINSKAS ◽  
Tomas MACKEVIČIUS
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Fuel Consumption ◽  
Specific Fuel Consumption ◽  
Bench Test ◽  
Brake Specific Fuel Consumption ◽  
Fuel Blend ◽  
Performance And Emission ◽  
Rapeseed Methyl Ester ◽  
Smoke Opacity

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on rapeseed methyl ester (B) and rapeseed methyl ester -butanol (Bu5, Bu10, Bu15) blends, at various loads and 2000 rpm engine speeds. The experimental tests were performed on a four-stroke, single-cylinder, air-cooled diesel engine FL511. The bench test results showed that the brake specific fuel consumption increased, when operating on biodiesel-butanol fuel blends compared to neat biodiesel. The maximum brake thermal efficiency sustained at the levels from 7.3% to 12.9% lower in comparison with neat biodiesel operating at low engine load. When the engine was running at maximum torque mode using biodiesel-butanol fuel blend Bu15 the total emissions of nitrogen oxides decreased. Thus, the greatest fossil fuel challenge related with the simultaneous reduction of both the NOx emissions and the smoke opacity (PM) could be reasonably solved by switching a diesel engine on totally renewable biodiesel-n-butanol biofuel blends.Keywords: diesel engine, rapeseed oil derived biodiesel, n-butanol, engine efficiency, brake specific fuel consumption, emissions, smoke opacity.

Performance and Emission Characteristics of a Mixed Biodiesel Fueled CI Engine

2015 ◽  
Vol 766-767 ◽  
pp. 557-561
Author(s):  
S. Arunprasad ◽  
Thangavel Balusamy ◽  
S. Sivalakshmi
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Emission Characteristics ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Ci Engine ◽  
Smoke Opacity

In this present paper, an attempt has been made to examine the performance and emission characteristics of a single cylinder diesel engine fueled with blends of mixed biodiesel (Thevetia peruviana, Neem, Jatropha, Pongamia). Experiments were conducted with various blends of mixed biodiesel in CI engine for different loads. The results show that lower brake thermal efficiency and higher brake specific fuel consumption were obtained with mixed biodiesel blends when compared with diesel. Lower the value of CO and HC and higher the value of CO2 emissions were determined for mixed biodiesel blends compared to that of diesel. Also, higher in NOx and lower smoke opacity were found compared to diesel.

scholarly journals Effect of Parameters Behavior of Simarouba Methyl Ester Operated Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4973
Author(s):  
Keerthi Kumar N. ◽  
N. R. Banapurmath ◽  
T. K. Chandrashekar ◽  
Jatadhara G. S. ◽  
Manzoore Elahi M. Soudagar ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Hole Diameter ◽  
Design Parameters ◽  
Engine Operation ◽  
Brake Thermal Efficiency ◽  
Smoke Opacity

Being an energy source of another origin, the compression ignition (CI) engine’s typical design parameters might not suit Simarouba oil methyl ester (SuOME). Present experimental investigation targets are determining the effects of engine design parameters, including fuel injection pressure and nozzle geometry, on the engine, concerning performance and emissions such as carbon monoxide (CO), unburnt hydrocarbon (HC), oxides of nitrogen (NOx), and smoke opacity, with SuOME as fuel. Comparisons of brake thermal efficiency (BTE) and different emissions from the engine tailpipe were performed for different fuel injection pressures and a number of injector holes and diameter of orifices were opened in the injector to find the optimum combination to run the engine with SuOME. It was observed that the combined effect of an increase in injection pressure of 240 bar from 205 bar, and increasing number of injector holes from three to six with reduced injector hole diameters from 0.2 to 0.3 mm, recorded higher brake thermal efficiency with reduced emission levels for the SuOME mode of operation compared to the baseline standard operation with SuOME. For 240 bar compared to 205 bar of injection pressure (IP) for SuOME, the BTE increased by 2.35% and smoke opacity reduced by 1.45%. For six-hole fuel injectors compared to three-hole injectors, the BTE increased by 3.19%, HC reduced by 9.5%, and CO reduced by 14.7%. At 240 bar IP, with the six-hole injector having a 0.2 mm hole diameter compared to the 0.3 mm hole diameter, the BTE increased by 5%, HC reduced by 5.26%, CO reduced by 25.61%, smoke reduced by 10%, while NOx increased marginally by 0.27%. Hence, the six-hole FI, 240 IP, 0.2 mm FI diameter holes are suitable for diesel engine operation fueled by Simarouba biodiesel.

Effect of Cetane Number Improver on Emission Characteristics of Methanol/Diesel Blend Fuel

2012 ◽  
Vol 512-515 ◽  
pp. 1888-1891
Author(s):  
Jia Yi Du ◽  
Wei Xun Zhang ◽  
Deng Pan Zhang ◽  
Zhen Yu Sun
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Cetane Number ◽  
Nox Emission ◽  
Fuel Load ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Maximum Torque ◽  
Blend Fuel ◽  
Co Emission

The influence of cetane number improver on emission characteristics of diesel engine fueled with methanol/diesel blend fuel was investigated. Methanol/diesel blend fuel was prepared, in which the methanol content is 10%, different mass fraction (0%，0.5%) of cetane number improver were added to the blend fuel. Load characteristic experiments at maximum torque speed of the engine were carried out on 4B26 direct injection diesel engine. The results show that, compared with the engine fueled with diesel, the CO emission increases under low loads and reduces under medium and high loads, the HC emission increases, the NOx emission decreases under medium and low loads and increases under high loads, the soot emission reduces significantly when the diesel engine fueled with blends. When cetane number improver was added to blends, the CO and NOx emission reduces, the HC emission decreases, the soot emission increases to some extent compared with the methanol/dieselblend fuel without cetane number improver.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Emissions Characteristics of a Diesel Engine with GTL and Biodiesel Fuels

2014 ◽  
Vol 1008-1009 ◽  
pp. 995-1000
Author(s):  
Pi Qiang Tan ◽  
Shu Wang ◽  
Yuan Hu Zhi ◽  
Di Ming Lou
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Brake Specific Fuel Consumption ◽  
Biodiesel Blend ◽  
Hc Emissions ◽  
Gas To Liquids ◽  
Biodiesel Fuels ◽  
Co Emission

Emission characteristics of an electronic-controlled high pressure common-rail diesel engine with low-blend Gas-to-liquids (GTL) and low-blend biodiesel fuels are studied. Pure diesel fuel, G10 fuel (10% GTL blend with diesel fuel) and B10 fuel (10% biodiesel blend with diesel fuel) are used in this research. The results show that torque of the engine with pure diesel fuel is higher than G10 fuel, and B10 fuel is the lowest. Compared to the pure diesel fuel, the brake specific fuel consumption (BSFC) of the engine with G10 fuel decreases, but the B10 fuel increases slightly. Hydrocarbon (HC) emissions of the engine with G10 fuel or B10 fuel are lower than the pure diesel fuel, and the carbon monoxide (CO) emission increases slightly, and nitrogen oxides (NOx) emissions have no distinct change. Compared to the G10 fuel, the CO and HC emissions of the engine with B10 fuel are lower.

Sign in / Sign up

Export Citation Format

Share Document