Measuring hoof slip of the leading limb on jump landing over two different equine arena surfaces

2012 ◽  
Vol 8 (1) ◽  
pp. 33-39 ◽  
Author(s):  
O. Orlande ◽  
S.J. Hobbs ◽  
J.H. Martin ◽  
A.G. Owen ◽  
A.J. Northrop
Keyword(s):  
Surface Properties ◽  
High Speed ◽  
Surface Hardness ◽  
Horizontal Displacement ◽  
Jump Landing ◽  
Reference Marker ◽  
Surface Wax ◽  
Significant Difference ◽  
Wax Content ◽  
The Moment

The amount of hoof slip at the moment of impact can cause musculoskeletal injuries to the horse. Risk of injury is influenced by surface properties, however there is limited understanding of the effect on hoof slip during jump landing. The objectives of this study were to compare hoof slip on two different surfaces and investigate relationships between hoof slip and surface properties. A contact mat and hoof reference marker were designed and validated, the former to indicate the moment of impact and the latter to provide a visible reference marker on the lateral hoof wall. The leading right forelimb of six horses was recorded during jump landing on two different surfaces. Five trials, plus one where the forelimb landed on a contact mat were recorded at 500 Hz using a calibrated high speed camera positioned perpendicular to landing. Surface hardness, penetrability and traction were measured between horses. Horizontal displacement of the hoof reference marker was plotted and smoothed with a Butterworth filter at 25 Hz cut-off. Hoof slip was measured from impact to mid-stance. Data were analysed using ANOVA and Pearson correlations. A significant difference in hoof slip (10% wax = 4.9�2.1 cm and 3% wax = 7.4±3.6 cm) was found between the two surfaces (P<0.01). In addition, hoof slip was correlated with all surface measurements (hardness, penetrability and traction) on the 10% wax surface, but none on the 3% wax surface. Wax content appears to influence hoof slip during jump landing as greater hoof slip was measured on a 3% wax surface and variability on this surface was greater for the group. The results suggest that wax content had an effect on surface properties and greater variability in hardness and traction on the 3% wax surface influenced the consistency with which the horses jumped upon it.

Comprehensive Studies on Rarefied Jet and Jet Impingement Flows with Gaskinetic Methods

2017 ◽  
Vol 22 (3) ◽  
pp. 712-741 ◽  
Author(s):  
Chunpei Cai ◽  
Xin He ◽  
Kai Zhang
Keyword(s):  
Heat Flux ◽  
Flat Plate ◽  
Surface Properties ◽  
Knudsen Number ◽  
High Speed ◽  
Direct Simulation Monte Carlo ◽  
Jet Impingement ◽  
The Moment ◽  
Plate Center ◽  
Comprehensive Studies

AbstractThis paper presents comprehensive studies on two closely related problems of high speed collisionless gaseous jet from a circular exit and impinging on an inclined rectangular flat plate, where the plate surface can be diffuse or specular reflective. Gaskinetic theories are adopted to study the problems, and several crucial geometry-location and velocity-direction relations are used. The final complete results include flowfield properties such as density, velocity components, temperature and pressure, and impingement surface properties such as coefficients of pressure, shear stress and heat flux. Also included are the averaged coefficients for pressure, friction, heat flux, moment over the whole plate, and the averaged distance from the moment center to the plate center. The final results include complex but accurate integrations involving the geometry and specific speed ratios, inclination angle, and the temperature ratio. Several numerical simulations with the direct simulation Monte Carlo method validate these analytical results, and the results are essentially identical. Exponential, trigonometric, and error functions are embedded in the solutions. The results illustrate that the past simple cosine function approach is rather crude, and should be used cautiously. The gaskinetic method and processes are heuristic and can be used to investigate other external high Knudsen number impingement flow problems, including the flowfield and surface properties for high Knudsen number jet from an exit and flat plate of arbitrary shapes. The results are expected to find many engineering applications.

Maximum Temperature Through a Yttrium Stabilized Zirconia Ceramic After Er,Cr:YSGG Laser Irradiation

2020 ◽  
Vol 02 ◽  
Author(s):  
Laurel Stringer ◽  
Sarah Malley ◽  
Darrell M. Hutto ◽  
Jason A. Griggs ◽  
Susana M. Salazar Marocho
Keyword(s):  
High Speed ◽  
Potential Method ◽  
Maximum Temperature ◽  
Zirconia Ceramic ◽  
Tooth Pulp ◽  
Control Group ◽  
Stabilized Zirconia ◽  
Significant Difference ◽  
Power Setting ◽  
Group A

Background: The most common approach to remove yttria stabilized zirconia (YSZ) fixed-dental prostheses (FDPs) is by means of diamond burs attached to a high-speed handpiece. This process is time-consuming and destructive. The use of lasers over mechanical instrumentation for removal of FDPs can lead to efficient and predictable restoration retrievability. However, the heat produced might damage the tooth pulp (>42˚C). Objective: The purpose of this study was to determine the maximum temperature (T) reached during the use of different settings of the erbium, chromium:yttrium-scandium-gallium-garnet Er,Cr:YSGG laser through a YSZ ceramic. Methods: YSZ slices (1 mm thick) were assigned into 7 groups. For the control group, a diamond bur was used to cut a 1 mm groove into the YSZ slices. For the 6 experimental groups, the laser was operated at a constant combination of 33% water and 66% air during 30 s with two different power settings (W) at three frequencies (PPS), as follows (W/PPS): 2.5/20, 2.5/30, 2.5/45, 4.5/20, 4.5/30, 4.5/45. The T through the YSZ slice was recorded in degrees Celsius by using a digital thermometer with a K thermocouple. Results: The median T of the control group was 26.5˚C. The use of 4.5 W resulted in the median T (˚C) of 44.2 at 20 PPS, 53.3 at 30 PPS, and 58.9 at 45 PPS, while 2.5 W showed 34.6, 31.6, and 25.0 at 20, 30, and 45 PPS, respectively. KruskalWallis one-way ANOVA showed that within each power setting, the T was similar. The high power and lowest frequency (4.5/20) showed no significant difference from the 2.5 W settings and the control group. Conclusion: The lower power setting (2.5 W) is a potential method for the use of the Er,Cr:YSGG laser to debond YSZ structures. The higher power (4.5 W) with high frequencies (30 and 45 PPS) is unsuitable.

scholarly journals Outcome of the use of 0.9% saline versus 0.45% saline for fluid rehydration in moderate and severe diabetic ketoacidosis in children

2021 ◽  
Vol 69 (1) ◽  
Author(s):  
Nora El Said Badawi ◽  
Mona Hafez ◽  
Heba Sharaf Eldin ◽  
Hend Mehawed Abdelatif ◽  
Shimaa Atef ◽  
...  
Keyword(s):  
Blood Glucose ◽  
Diabetic Ketoacidosis ◽  
Normal Saline ◽  
Sodium Concentration ◽  
Saline Group ◽  
Serum Electrolytes ◽  
Serum Chloride ◽  
Significant Difference ◽  
Rehydration Solution ◽  
The Moment

Abstract Background The debate for the optimum sodium concentration in the rehydration solution in diabetic ketoacidosis (DKA) persists till the moment. The aim was to compare the outcome of 0.9% saline versus 0.45% saline in children with moderate and severe (DKA) regarding the effect on serum electrolytes, duration of DKA resolution and the incidence of hyperchloremia. Results A retrospective analysis of 121 children with moderate or severe DKA was done. After the initial 4 h in which both groups received normal saline, patients were divided into two groups continuing on 0.9% (N=72) or switched to 0.45% saline (N=49). Serum chloride and Cl/Na ratios were significantly higher in 0.9% saline group at 4 and 8 h. The 0.9% saline group had significantly higher proportion of hyperchloremia at 4 and 8 h (P value: 0.002, 0.02). The median duration of correction of DKA (14 h among 0.9% saline versus 10 h among 0.45% saline) without significant difference (P value= 0.43). The change in plasma glucose, effective osmolarity, corrected Na levels were comparable between groups. Conclusion There is an unavoidable iatrogenically induced rise in serum chloride with higher incidence of hyperchloremia with the use of normal saline in rehydration of children presenting in DKA and shock. The use of 0.45% saline as post-bolus rehydration fluid is not associated with a decline in the corrected serum sodium concentration and does not affect the rate of correction of acidosis or rate of drop in blood glucose or duration of DKA resolution when compared to normal saline.

scholarly journals Lignin-Containing Coatings for Packaging Materials—Pilot Trials

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1595
Author(s):  
Asif Javed ◽  
Peter Rättö ◽  
Lars Järnström ◽  
Henrik Ullsten
Keyword(s):  
High Speed ◽  
Water Solubility ◽  
Transmission Rate ◽  
Kraft Lignin ◽  
Packaging Materials ◽  
Water Contact ◽  
Pilot Trials ◽  
Significant Difference ◽  
Ph Level ◽  
Ammonium Zirconium Carbonate

One severe weakness of most biopolymers, in terms of their use as packaging materials, is their relatively high solubility in water. The addition of kraft lignin to starch coating formulations has been shown to reduce the water solubility of starch in dry coatings. However, lignin may also migrate into aqueous solutions. For this paper, kraft lignin isolated using the LignoBoost process was used in order to examine the effect of pH level on the solubility of lignin with and without ammonium zirconium carbonate (AZC). Machine-glazed (MG) paper was coated in a pilot coating machine, with the moving substrate at high speed, and laboratory-coated samples were used as a reference when measuring defects (number of pinholes). Kraft lignin became soluble in water at lower pH levels when starch was added to the solution, due to the interactions between starch and lignin. This made it possible to lower the pH of the coating solutions, resulting in increased water stability of the dry samples; that is, the migration of lignin to the model liquids decreased when the pH of the coating solutions was reduced. No significant difference was observed in the water vapor transmission rate (WVTR) between high and low pH for the pilot-coated samples. The addition of AZC to the formulation reduced the migration of lignin from the coatings to the model liquids and led to an increase in the water contact angle, but also increased the number of pinholes in the pilot-coated samples.

Investigation on the mechanical properties of press-hardened boron steel sheets using the conductive heating technique

2020 ◽  
Vol 234 (8) ◽  
pp. 1084-1098
Author(s):  
O Kocar ◽  
H Livatyalı
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Boron Steel ◽  
Fast Heating ◽  
Heating Method ◽  
Conductive Heating ◽  
Press Hardening ◽  
High Speed Impact ◽  
Significant Difference ◽  
Structural Parts

An aluminized 22MnB5 (Boron) steel sheet, used for structural parts in the automotive industry, was subjected to press-hardening followed by austenitizing, both in a conventional furnace and via the conductive (electric resistance) heating method, an innovative technique based on the Joule’s principle for fast heating of the sheet metal. Conductive heating presents a number of advantages over the in-furnace heating method. These include a more efficient use of energy, as well as the requirement of less time and space for heating, thus lowering costs. After press-hardening was performed using both methods, the microstructural and mechanical characterizations of both specimens were examined for optical microscopy, hardness, tensile strength, and high-speed impact tests. The results showed that the press-hardening process transformed the ferritic–pearlitic microstructure in the as-received state into martensite after die quenching and caused a substantial increase in hardness and strength at the expense of ductility and impact toughness. On the other hand, no significant difference was observed in either the microstructure or mechanical properties with respect to the heating method used. The results obtained in the present investigation concur with the findings of current literature.

scholarly journals Influence of rigidity of retainers on dynamic behavior of implant-supported removable partial dentures

2020 ◽  
Vol 6 (1) ◽  
Author(s):  
Toshifumi Nogawa ◽  
Masayasu Saito ◽  
Naomichi Murashima ◽  
Yoshiyuki Takayama ◽  
Atsuro Yokoyama
Keyword(s):  
Dynamic Behavior ◽  
Horizontal Displacement ◽  
Vertical Displacement ◽  
Denture Base ◽  
Second Molar ◽  
Mechanical Simulation ◽  
Computed Tomography Images ◽  
Significant Difference ◽  
Abutment Teeth ◽  
Distal Extension

Abstract Background Implant-supported removable partial dentures (ISRPDs) are an effective treatment for partially edentulous patients. ISRPDs improve patients’ satisfaction and oral function to a greater extent than RPDs by improving denture stability and enhancing support. However, the effect of a type of direct retainer on displacement of the abutment teeth and dentures in ISRPDs remains unclear. Therefore, we made a resin mandibular model of unilateral mandibular distal-extension partial edentulism for mechanical simulation and compared the dynamic behavior of the abutment teeth and the denture base among different tooth-borne retainers with various rigidities for RPDs and ISRPDs. Methods A resin mandibular model for mechanical simulation that had unilateral mandibular distal-extension edentulism and was missing the first molar, second molar, first premolar, and second premolar, and a denture fabricated from the patient’s computed tomography images were used. Three types of direct retainers with different connecting rigidities were evaluated. The vertical displacement of the denture base and buccal and lingual sides and the mesial displacement of the abutment teeth were measured. Results Regardless of the rigidity of the direct retainers and loading positions, the displacement of the denture bases in the ISRPDs was significantly smaller than that in the RPDs (P < 0.001). There was no significant difference in vertical displacement of the denture bases among direct retainers with various connecting rigidities in the ISRPDs. Conversely, horizontal displacement of the abutment teeth in both the RPDs and ISRPDs tended to be larger with the cone crown telescope, which has high rigidity, than with the cast cingulum rest and wire clasp, which have much lower rigidities. Conclusion Our results suggested that cast cingulum rest and wire clasps as direct retainers are appropriate ISRPDs to minimize denture movement and suppress displacement of the remaining teeth in patients with unilateral mandibular distal-extension partial edentulism.

Betadine has a ciliotoxic effect on ciliated human respiratory cells

2014 ◽  
Vol 129 (S1) ◽  
pp. S45-S50 ◽  
Author(s):  
J H Kim ◽  
J Rimmer ◽  
N Mrad ◽  
S Ahmadzada ◽  
R J Harvey
Keyword(s):  
Epithelial Cells ◽  
High Speed ◽  
Imaging System ◽  
Beat Frequency ◽  
Ciliary Beat Frequency ◽  
Positive Control ◽  
Clinical Dose ◽  
Significant Difference ◽  
Sinonasal Mucosa ◽  
Ciliary Beat

AbstractObjective:This study investigated the effect of Betadine on ciliated human respiratory epithelial cells.Methods:Epithelial cells from human sinonasal mucosa were cultured at the air–liquid interface. The cultures were tested with Hanks' balanced salt solution containing 10 mM HEPES (control), 100 µM ATP (positive control), 5 per cent Betadine or 10 per cent Betadine (clinical dose). Ciliary beat frequency was analysed using a high-speed camera on a computer imaging system.Results:Undiluted 10 per cent Betadine (n = 6) decreased the proportion of actively beating cilia over 1 minute (p < 0.01). Ciliary beat frequency decreased from 11.15 ± 4.64 Hz to no detectable activity. The result was similar with 5 per cent Betadine (n = 7), with no significant difference compared with the 10 per cent solution findings.Conclusion:Betadine, at either 5 and 10 per cent, was ciliotoxic. Caution should be applied to the use of topical Betadine solution on the respiratory mucosal surface.

The Effect of Bleach Liquid and Household Cleaner on Surface Hardness and Roughness of Acrylic Base of Orthodontic Appliances

2021 ◽  
Author(s):  
Saeed Noorollahian ◽  
Farinaz Shirban ◽  
Vahid Mojiri
Keyword(s):  
Surface Roughness ◽  
Hydrochloric Acid ◽  
Sodium Hypochlorite ◽  
Surface Hardness ◽  
Acrylic Resin ◽  
Liquid Sodium ◽  
P Value ◽  
Orthodontic Appliances ◽  
Acrylic Resins ◽  
Significant Difference

Introduction: The daily use of orthodontic removable plates can interfere with the self-cleansing function of the mouth. Although various techniques have been proposed for cleaning removable orthodontic appliances, there is no consensus on the use of a safe method that preserves the physical properties of the appliance. This study aimed to investigate the effect of using hydrochloric acid (10%, for removal of mineral deposits) and sodium hypochlorite (5.25%, to remove organic matter and discolorations) on surface hardness and roughness of self-cure orthodontic acrylic resins. Materials & Methods: This cross-sectional laboratory study was conducted in the fall of 2017 at Isfahan University of Medical science and Isfahan University of Technology. In this study two orthodontic acrylic resins (Orthocryl® and Acropars®) were used. Eighty samples (12×10×3 mm) from each one were fabricated and divided into four groups (n = 20). Group 1: 15 minutes immersion in household cleaner liquid (Hydrochloric acid, 10%) followed by15 minutes immersion in household bleach liquid (Sodium Hypochlorite, 5.25%). In group 2, immersions were repeated just like group two times and in group 3, were done three times. Group 4 was as control and had no immersion. The surface hardness and roughness of samples were measured. Data were analyzed with Two Way ANOVA and the significance level was set at 0.05. Results: The number of immersion procedures did not significantly affect the surface hardness (p value = 0.958) and surface roughness (p value = 0.657) in the different study groups. There was no significant difference in the surface hardness between the two acrylic resin brands (p value = 0.077); however, Acropars acrylic resin samples exhibited significantly higher surface roughness compared to the Orthocryl acrylic resin samples(p value < 0.001). Conclusion: 15 minutes of immersion in 10% HCl, followed by 15 minutes of immersion in 5.25% NaOCl and repetition of the procedure three times did not significantly affect the surface hardness and roughness of self-cured acrylic resins.

Venom flow in rattlesnakes: mechanics and metering

2001 ◽  
Vol 204 (24) ◽  
pp. 4345-4351
Author(s):  
Bruce A. Young ◽  
Krista Zahn
Keyword(s):  
Functional Morphology ◽  
Delivery System ◽  
Flow Rate ◽  
High Speed ◽  
Distal Portion ◽  
Retrograde Flow ◽  
Crotalus Atrox ◽  
Direct Recording ◽  
Significant Difference ◽  
Digital Videography

SUMMARY The functional morphology of venom injection in Crotalus atrox was explored using high-speed digital videography combined with direct recording of venom flow using perivascular flow probes. Although venom flow was variable, in most strikes the onset of venom flow was coincidental with fang penetration, and retrograde flow (venom suction) was observed prior to fang withdrawal. The duration of venom flow was consistently less than the duration of fang penetration. The occurrence of retrograde flow, ‘dry bites’ (which accounted for 35 % of the strikes) and unilateral strikes all support a hypothesis for venom pooling in the distal portion of the venom-delivery system. No significant difference in temporal or volumetric aspects of venom flow were found between defensive strikes directed at small and large rodents. With the species and size of target held constant, the duration of venom flow, maximum venom flow rate and total venom volume were all significantly lower in predatory than in defensive strikes.

Surface properties of composite resins with and without fluorides for bracket bonding / Propriedades de superfície de resinas compostas com e sem fluoretos para colagem de suportes

2021 ◽  
Vol 7 (7) ◽  
pp. 67267-67276
Author(s):  
Emillyn Jones Greijal Dias Holanda ◽  
José Guilherme Neves ◽  
Milton Santamaria-Jr ◽  
Silvia Amélia Scudeler Vedovello ◽  
Ana Rosa Costa ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Color Change ◽  
Composite Resins ◽  
Hardness Tester ◽  
Significant Difference ◽  
Post Test ◽  
Roughness Analysis ◽  
Diamond Paste ◽  
Penetration Time

The aim of this study was to evaluate the surface properties of orthodontic resins with and without fluoride. Forty disks, measuring 2 mm thick by 6 mm in diameter, were made of 4 bracket-bonding composite resins (n=10): Transbond Plus Color Change-3M/Unitek (TPCC); Transbond XT- 3M/Unitek (TXT), Orthocem -FGM (OC); Orthocem UV Trace-FGM (OCUV). The discs were photoactivated for 40 seconds with irradiance of 450 mW/cm2 and manually polished in sequence by silicon carbide sandpapers with 1200 and 2000 grain size and finished with diamond paste and felt disc. The surface microhardness analysis was performed using a Shimadzu Micro Hardness Tester HMV-2,000 (Shimadzu Corporation, Kyoto, Japan) with a load of 50 gF and a 5 second penetration time. Surface roughness readings were taken using a Surf Corder Roughness Meter (SE 1700- Kosaka, Lisboa-Portugal). For data analysis, ANOVA (one-way) was used, followed by Tukey's post-test (?=0.05). The microhardness results showed a difference (p?0.05) in the means of the orthodontic resins between TPCC and TXT with the other groups. After the surface roughness analysis, the averages showed that TPCC resin showed higher roughness compared to OC and OCUV (p?0.05), and there was no statistical difference with TXT. It was concluded that statistically the composite resins with fluoride showed significant difference regarding hardness and roughness.

Sign in / Sign up

Export Citation Format

Share Document