Study on High-Frequency Quenching of Steel Tube Screw Thread Lined Glass Used for Petroleum Pipe Line

2012 ◽  
Vol 155-156 ◽  
pp. 668-673
Author(s):  
Li Chen ◽  
Xi Ming Liu
Keyword(s):  
Heat Treatment ◽  
High Frequency ◽  
Steel Tube ◽  
Screw Thread ◽  
Pipe Line ◽  
Power Frequency ◽  
Joining Strength ◽  
Screw Threads ◽  
High Degree ◽  
Quenching And Tempering

The easy-to-wear and easy-to-deform of screw threads resulting in screw thread damage often form to the steel tube lined glass used for petroleum pipe because of their low joining strength. The reason resulting above problem was found through experiments. Moreover, it was found that the high-frequency quenching and tempering heat treatment process could effectively improve strength of screw threads with optimized process parameters. The optimized parameters are output power, frequency, and thickness of steel tube wall, high degree of screw threads, induction coil current, relative speed, and medium jet pressure, respectively. The high-frequency quenching and tempering heat treatment processes are a new approach to improve the hardening of strength for the steel tube lined glass.

INFLUENCE THE QUENCHING AND TEMPERING ON THE MICROSTRUCTURE, MECHANICAL PROPERTIES AND SURFACE ROUGHNESS, OF MEDIUM CARBON STEEL

2018 ◽  
Vol 18 (1) ◽  
pp. 125-135
Author(s):  
Sattar H A Alfatlawi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Surface Roughness ◽  
Carbon Steel ◽  
Cold Water ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Heating And Cooling ◽  
Treatment Processes ◽  
Quenching And Tempering

One of ways to improve properties of materials without changing the product shape toobtain the desired engineering applications is heating and cooling under effect of controlledsequence of heat treatment. The main aim of this study was to investigate the effect ofheating and cooling on the surface roughness, microstructure and some selected propertiessuch as the hardness and impact strength of Medium Carbon Steel which treated at differenttypes of heat treatment processes. Heat treatment achieved in this work was respectively,heating, quenching and tempering. The specimens were heated to 850°C and left for 45minutes inside the furnace as a holding time at that temperature, then quenching process wasperformed in four types of quenching media (still air, cold water (2°C), oil and polymersolution), respectively. Thereafter, the samples were tempered at 200°C, 400°C, and 600°Cwith one hour as a soaking time for each temperature, then were all cooled by still air. Whenthe heat treatment process was completed, the surface roughness, hardness, impact strengthand microstructure tests were performed. The results showed a change and clearimprovement of surface roughness, mechanical properties and microstructure afterquenching was achieved, as well as the change that took place due to the increasingtoughness and ductility by reducing of brittleness of samples.

Network Carbide Inheritance during Heat Treatment Process of Large Shield Machine Bearing Steel GCr15SiMn

2015 ◽  
Vol 817 ◽  
pp. 115-120 ◽  
Author(s):  
Dan Zhang ◽  
Le Yu Zhou ◽  
Chao Lei Zhang ◽  
Chao Huang ◽  
Min Zhao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Treatment Process ◽  
Bearing Steel ◽  
Treatment Temperature ◽  
Heat Treatment Process ◽  
Soaking Time ◽  
Hot Rolled ◽  
Chinese Standard ◽  
Shield Machine ◽  
Quenching And Tempering

Network carbide inheritance during heat treatment process of large shield machine bearing steel GCr15SiMn was investigated by heat treatment experiments and quantitative metallographic. Samples with the proeutectoid cementite network thickness in the range of 0.19~0.54 μm were obtained by changing austenitizing temperature and soaking time of pearlite transformation. The results show that the network in hot rolled bar can be improved when the pre-heat treatment temperature is 950 °C. When the network thickness is above 0.40 μm, the undissolved cementite networks present in microstructures after quenching and tempering. In a Chinese standard, the network grades are 1.5 and 3.0 degree when the networks thickness are 0.40 μm and 0.54 μm, respectively. The critical network thickness that can be eliminated by heat treatment is 0.29 μm.

scholarly journals Failure Analysis of Rheocast Cylinder Head Covers of Hypereutectic Al–Si Alloys

2020 ◽  
Author(s):  
Jian Feng
Keyword(s):  
Heat Treatment ◽  
Surface Morphology ◽  
Service Time ◽  
Shot Peening ◽  
High Frequency ◽  
Cylinder Head ◽  
Die Casting ◽  
Fatigue Properties ◽  
Homogeneous Distribution ◽  
Engine Components

AbstractThe purpose of the present study is to determine the cause of failures of semisolid rheocast cylinder head covers of hypereutectic modified LM30 alloys. The covers, manufactured by rheocasting, a process that consists of the incorporation and homogeneous distribution of the reinforcements in semisolid metal (SSM) before die casting, were shot-peened after heat treatment to increase the fatigue resistance. However, these engine components failed during operation after a short service time. The major flaws were located by radiography. The microstructure was controlled by metallography. Significant interactions between shot peening and surface/subsurface contaminants were identified by surface morphology and fractography. The fatigue properties of hypereutectic alloys were investigated by a high-frequency vibrophore. It was identified that the failure was related to the cleanliness of SSM as well as the rheocasting process. Recommendations were given to prevent the recurrence of similar failures.

scholarly journals Simultaneously Enhanced Thermal Conductivity and Breakdown Performance of Micro/Nano-BN Co-Doped Epoxy Composites

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3521
Author(s):  
Chuang Zhang ◽  
Jiao Xiang ◽  
Shihang Wang ◽  
Zhimin Yan ◽  
Zhuolin Cheng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
High Frequency ◽  
Breakdown Strength ◽  
Epoxy Composites ◽  
Endurance Time ◽  
Insulating Materials ◽  
Power Frequency ◽  
High Frequency Devices ◽  
Co Doped ◽  
Enhanced Thermal Conductivity

Micro/nano- BN co-doped epoxy composites were prepared and their thermal conductivity, breakdown strength at power frequency and voltage endurance time under high frequency bipolar square wave voltage were investigated. The thermal conductivity and breakdown performance were enhanced simultaneously in the composite with a loading concentration of 20 wt% BN at a micro/nano proportion of 95/5. The breakdown strength of 132 kV/mm at power frequency, the thermal conductivity of 0.81 W∙m−1∙K−1 and voltage endurance time of 166 s were obtained in the composites, which were approximately 28%, 286% and 349% higher than that of pristine epoxy resin. It is proposed that thermal conductive pathways are mainly constructed by micro-BN, leading to improved thermal conductivity and voltage endurance time. A model was introduced to illustrate the enhancement of the breakdown strength. The epoxy composites with high thermal conductivity and excellent breakdown performance could be feasible for insulating materials in high-frequency devices.

scholarly journals Factors affecting the temperature increasing rate in arc-shaped bamboo pieces during high-frequency heating

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 2656-2667
Author(s):  
Feihu Chang ◽  
Yanhe Liu ◽  
Bin Zhang ◽  
Wansi Fu ◽  
Pengfei Jiang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Moisture Content ◽  
Electric Field ◽  
Heating Rate ◽  
High Frequency ◽  
Great Influence ◽  
Chord Length ◽  
High Frequency Electric Field ◽  
Frequency Electric Field ◽  
Frequency Heating

In the process of applying the high-frequency heating technology to bamboo heat treatment, controlling the material temperature has a great influence on the quality of bamboo forming. Therefore, research on the heat transfer mechanism of high-frequency heating of arc-shaped bamboo pieces is of great importance. In this paper, the influence of different moisture content, chord length, and plate voltage on the heating rate of arc-shaped bamboo pieces under high-frequency electric field were studied. The moisture content of bamboo had the most remarkable effect on the heating rate. With increased moisture content, the temperature rose faster. The selection of the plate voltage had an obvious influence on the heating. If the voltage was low, the heating rate was too slow, the heating time was long, or the voltage was high, it was easy to cause electric field breakdown and damage the bamboo pieces. As the chord length decreased, the heating rate gradually increased. When the radian of the arc-shaped bamboo pieces could be ignored, the heating rate was the fastest. The results showed that under certain conditions, the arc-shaped bamboo pieces showed a good heat treatment effect in a high-frequency electric field.

scholarly journals Austenite Reversion Tempering-Annealing of 4 wt.% Manganese Steels for Automotive Forging Application

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 575 ◽  
Author(s):  
Alexander Gramlich ◽  
Robin Emmrich ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Chemical Composition ◽  
Impact Toughness ◽  
Temperature Control ◽  
Annealing Process ◽  
Air Cooling ◽  
Metastable Austenite ◽  
Quenching And Tempering ◽  
Manganese Steels

New medium Mn steels for forged components, in combination with a new heat treatment, are presented. This new annealing process implies air-cooling after forging and austenite reversion tempering (AC + ART). This leads to energy saving compared to other heat treatments, like quenching and tempering (Q + T) or quenching and partitioning (Q + P). Furthermore, the temperature control of AC + ART is easy, which increases the applicability to forged products with large diameters. Laboratory melts distinguished by Ti, B, Mo contents have been casted and consecutively forged into semi-finished products. Mechanical properties and microstructure have been characterized for the AC and the AC + ART states. The as forged-state shows YS from 900 MPa to 1000 MPa, UTS from 1350 MPa to 1500 MPa and impact toughness from 15 J to 25 J. Through the formation of nanostructured retained metastable austenite an increase in impact toughness was achieved with values from 80 J to 100 J dependent on the chemical composition.

Microstructure and Mechanical Properties of High Strength Alloyed Steel for Aerospace Application

2018 ◽  
Vol 284 ◽  
pp. 351-356 ◽  
Author(s):  
Mikhail V. Maisuradze ◽  
Maksim A. Ryzhkov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Single Stage ◽  
The Novel ◽  
Tempering Temperature ◽  
Quenching And Partitioning ◽  
Aerospace Application ◽  
Cooling Conditions ◽  
Quenching And Tempering

The high strength aerospace steel alloyed with Cr, Mn, Si, Ni, W and Mo was studied. The austenite transformations under continuous cooling conditions were investigated using the dilatometer analysis at the cooling rates 0.1...30 °C/s. The mechanical properties of the studied steel were determined after the conventional quenching and tempering heat treatment. The dependences of the mechanical properties on the tempering temperature were obtained. The novel quenching and partitioning heat treatment was applied to the steel under consideration. The microstructure and the mechanical properties were studied after three different modes of the quenching and partitioning (QP) treatment: single-stage QP, two-stage QP and single-stage QP with subsequent tempering (QPT).

Sign in / Sign up

Export Citation Format

Share Document