Study on the Preparation Process of Corn Straw-Pumice Composite Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 955-958
Author(s):  
Jian Suo Ma ◽  
Jing Sun ◽  
Huan Qin Cai ◽  
Run Shan Bai
Keyword(s):  
Water Absorption ◽  
Building Materials ◽  
Raw Materials ◽  
Northern China ◽  
Preparation Process ◽  
Corn Straw ◽  
Molding Process ◽  
Main Crop ◽  
Large Water ◽  
Materials Used

In order to prepare energy saving and environmental protection building materials, a new kind of concrete was made by the combination of corn stalks which is the main crop in northern China, natural pumice resources and cement. Corn stalks and pumice are all lightweight material with open pores and large water absorption; therefore they must be pretreated before preparing concrete by blocking holes to reduce the amount of grout. The raw materials used in the experiments are lightweight materials; it is advisable to adopt the pressure vibration molding process to reduce aggregate stratification.

scholarly journals Architectural ruins: geoculture of the anatomy of buildings as illustrated by Casa Ippolito, Malta

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Lino Bianco
Keyword(s):  
Material Culture ◽  
Building Materials ◽  
Raw Materials ◽  
Primary Source ◽  
Secondary Sources ◽  
Non Invasive ◽  
History Of ◽  
Aerial Vehicle ◽  
Materials Used ◽  
Building Physics

AbstractRuins are a statement on the building materials used and the construction method employed. Casa Ippolito, now in ruins, is typical of 17th-century Maltese aristocratic country residences. It represents an illustration of secondary or anthropogenic geodiversity. This paper scrutinises these ruins as a primary source in reconstructing the building’s architecture. The methodology involved on-site geographical surveying, including visual inspection and non-invasive tests, a geological survey of the local lithostratigraphy, and examination of notarial deeds and secondary sources to support findings about the building’s history as read from its ruins. An unmanned aerial vehicle was used to digitally record the parlous state of the architectural structure and karsten tubes were used to quantify the surface porosity of the limestone. The results are expressed from four perspectives. The anatomy of Casa Ippolito, as revealed in its ruins, provides a cross-section of its building history and shows two distinct phases in its construction. The tissue of Casa Ippolito—the building elements and materials—speaks of the knowledge of raw materials and their properties among the builders who worked on both phases. The architectural history of Casa Ippolito reveals how it supported its inhabitants’ wellbeing in terms of shelter, water and food. Finally, the ruins in their present state bring to the fore the site’s potential for cultural tourism. This case study aims to show that such ruins are not just geocultural remains of historical built fabric. They are open wounds in the built structure; they underpin the anatomy of the building and support insights into its former dynamics. Ruins offer an essay in material culture and building physics. Architectural ruins of masonry structures are anthropogenic discourse rendered in stone which facilitate not only the reconstruction of spaces but also places for human users; they are a statement on the wellbeing of humanity throughout history.

scholarly journals Characteristic of materials for the 3D printed building constructions by additive printing

2018 ◽  
Vol 222 ◽  
pp. 01013 ◽  
Author(s):  
Katarzyna Pacewicz ◽  
Anna Sobotka ◽  
Łukasz Gołek
Keyword(s):  
Building Materials ◽  
Raw Materials ◽  
New Technology ◽  
Setting Time ◽  
Three Dimensional ◽  
Construction Site ◽  
Printing Technology ◽  
Three Dimensional Printing ◽  
Materials Used ◽  
Dimensional Printing

Three dimensional printing is a promising new technology to erect construction objects. Around the world in every moment a new prototypes constructions are made by using this method. Three dimensional printing is taken into account as technology which can be used to print constructions in automated way on the Moon or Mars. The raw materials, which can be used with three dimensional printing have to fulfil basic requirements for those which are used in construction. That means that components of printing mortars are made from ingredients easily accessible in area nearby construction site and can be reusable. The cost of printing building objects due to that requirements is comparable to costs of traditional building, which are currently available. However additive techniques of printing needs a dedicated mortars for printer supplying. Characteristic for such mortars is: setting time, compressive strength, followability in the printing system, shape stability of every printed layer, controlling the hydration rate to ensure bonding with the subsequent layer, reusable capabilities, easily accessible raw materials, cost of such mixtures shouldn’t be too high in order to keep 3D printing competitive for traditional ways of building, mortar components should be recyclable and printing process should not influence negatively on an environment and people. All properties of printing mortars are determined by the device for additive application method. In this paper review of available materials used for three dimensional printing technology at construction site is presented. Presented materials were analysed in terms of requirements for building materials technology. Due to the lack of detailed information’s in available literature, regarding to the properties of raw materials, the results of this analysis may be used in the designing of new concrete mixtures for the use in three-dimensional printing technology for construction.

Quality Technological Properties of Foundry Exhaust Dust as Alternative Ceramic Coating Raw Materials

2015 ◽  
Vol 1088 ◽  
pp. 395-398
Author(s):  
Luiz Oliveira Veriano dalla Valentina ◽  
Marilena Valadares Folgueras ◽  
Wanessa Rejane Knop ◽  
Maria Cristina Pacheco do Nascimento ◽  
Glaucia Aparecida Prates
Keyword(s):  
Water Absorption ◽  
Bulk Density ◽  
Ceramic Coating ◽  
Raw Materials ◽  
Linear Shrinkage ◽  
Inert Atmosphere ◽  
Technological Properties ◽  
Foundry Industry ◽  
Ceramic Manufacturing ◽  
Materials Used

The work evaluates the possibility of the use the exhauster powder generated in the foundry process in ceramic mass atomized semigre type. The raw materials used were semi-stoneware kind atomized powder used on the coating ceramic manufacturing and dust exhaust byproduct supplied by a foundry industry both from brazilian industries . Tests were conducted using a heating rate of 10o.C / min and oxidant and / or inert atmosphere. Specimens contained different amounts of byproduct to the extent of 30% by mass, in order to verify the maximum addition of byproduct and were used in order to analyze the technological properties evaluation (water absorption linear shrinkage, bulk density). at the temperature of 1100 ° C showed higher difference between the results obtained and 1200o C this difference decreased.

Microstructural Analysis of Petroleum Waste Containing Ceramic Tile

2008 ◽  
Vol 591-593 ◽  
pp. 845-848 ◽  
Author(s):  
Bruno C.A. Pinheiro ◽  
J.N.F. Holanda
Keyword(s):  
Water Absorption ◽  
Microstructural Evolution ◽  
Ceramic Tile ◽  
Sintered Density ◽  
Raw Materials ◽  
Microstructural Analysis ◽  
Linear Shrinkage ◽  
Ceramic Tiles ◽  
Petroleum Waste ◽  
Materials Used

In this work is done a study on the sintered microstructure of ceramic tile paste incorporated with petroleum waste. The raw materials used were kaolin, sodic feldspar, quartz and petroleum waste. The ceramic tiles containing up to 5 wt% petroleum waste were prepared by uniaxial pressing and sintered at 1200°C. The microstructural evolution was examined by SEM. In addition, water absorption, linear shrinkage, and sintered density were determined. The results showed that the microstructure of the ceramic tiles is influenced by the added petroleum waste.

Comparison of Mechanical Properties of Fly Ash Artificial Geopolymer Aggregates with Natural Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 290-295 ◽  
Author(s):  
Alida Abdullah ◽  
Ku Amirrul Rahman Ku Yin ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Kamarudin Hussin ◽  
Mien Van Tran
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Specific Gravity ◽  
Water Absorption ◽  
Raw Materials ◽  
Construction Materials ◽  
High Water ◽  
Natural Aggregate ◽  
Materials Used ◽  
The Impact

This study was conducted to compare the mechanical properties of fly ash artificial geopolymer aggregates with natural aggregate (rock) in term of its impact strength, specific gravity and water absorption.The raw materials used were fly ash, sodium hydroxide, sodium silicate and natural aggregate. After the artificial geopolymer aggregate has been produced, its water absorption, specific gravity and aggregate impact test has been done. All results obtained were compared to natural aggregate. The result shows that the fly ash geopolymer aggregate are lighter than natural aggregate in term of its specific gravity. The impact value for fly ash artificial geopolymer aggregate slightly high compared to natural aggregate while it has high water absorption value compared to natural aggregate. As conclusion, the fly ash artificial geopolymer aggregate can be used as one of the construction materials in concrete as an alternative for coarse aggregate besides natural aggregate with more lightweight properties.

scholarly journals Pengujian Mekanik dan Biodegradabilitas Plastik Biodegradable Berbahan Baku Pati Bonggol Pisang dengan Penambahan Kitosan, Sorbitol, dan Minyak Kayu Manis

2019 ◽  
Vol 4 (2) ◽  
Author(s):  
Dewi Oetary ◽  
Syaubari Syaubari ◽  
Medyan Riza
Keyword(s):  
Tensile Strength ◽  
Environmental Pollution ◽  
Water Absorption ◽  
Raw Materials ◽  
Chitosan Nanoparticles ◽  
Biodegradable Plastic ◽  
Cinnamon Oil ◽  
Complete Degradation ◽  
Materials Used ◽  
Break Water

<p>Biodegradable plastic is an alternative to conventional plastic which has been very difficult to degrade and causes environmental pollution. Biodegradable plastic raw materials come from plants or plant wastes, so they are easily degraded by the environment and the utilization of waste becomes more efficient. The general objective of this study is to obtain the characteristics of plastics that meet the standards by varying the concentration of the materials used. This study used Kepok banana hump starch with variations in the concentration of chitosan, sorbitol, and cinnamon oil. The variable used is the ratio of weight of starch and water (1: 5). The concentration of chitosan nanoparticles was 0.25%, 0.5%, and 0.75%, sorbitol concentrations were 2 ml, 4 ml, and 6 ml, and the concentration of cinnamon was 0%, 0.5%, and 1%. Tests carried out are tensile strength, elongation of break, water absorption, and biodegradability. The best tensile strength results are 19.6 MPa, the best elongation is 47.69%, the highest water absorption is 53.77% and the lowest is 22.63%, and the complete degradation takes the longest time of 77 days.</p>

On the Issue of Reducing the Energy Intensity of the Silicate Composites Production with the Unconventional Aluminosilicate Raw Materials Use

2019 ◽  
Vol 974 ◽  
pp. 20-25 ◽  
Author(s):  
A.A. Volodchenko ◽  
Valery S. Lesovik ◽  
L.K. Zagorodnjuk ◽  
E.S. Glagolev
Keyword(s):  
Energy Saving ◽  
Building Materials ◽  
Energy Intensity ◽  
High Pressures ◽  
Raw Materials ◽  
High Reactivity ◽  
Raw Material ◽  
Green Technologies ◽  
Materials Used ◽  
Clay Rocks

The energy intensity of production of the most common wall materials in Russia is significantly higher than their foreign counterparts. The urgent task is to reduce the energy intensity of the production of building materials, to develop and introduce energy-saving nature-like technologies for the production of building materials, which corresponds to modern trends in the development of "green" technologies. It is possible to reduce the energy intensity of the production of silicate materials due to the transition from traditional raw materials to the use of unconventional aluminosilicate raw materials of various genesis, in particular, clay rocks of the unfinished stage of mineral formation. In the course of the research, the possibility of the synthesis of the new growth in the system “aluminosilicate raw material – calcium hydroxide – water” under the conditions of hydrothermal treatment was shown. Due to the high reactivity of the raw materials used, under the conditions of hydrothermal processing, the synthesis of tumors occurs not only at high pressures and temperatures, but also at temperatures up to 100 °C. This will allow to obtain efficient hollow-walled wall building materials using energy-saving technology.

Characterization and Properties of Lampang Kaolinite Clay for Standard Clay

2019 ◽  
Vol 798 ◽  
pp. 248-253
Author(s):  
Soravich Mulinta ◽  
Sakdiphon Thiansem
Keyword(s):  
Water Absorption ◽  
Bending Strength ◽  
Silicon Oxide ◽  
Raw Materials ◽  
Raw Material ◽  
Chemical Components ◽  
Kaolin Clay ◽  
Kaolinite Clay ◽  
X Ray ◽  
Materials Used

The aim of this study was to study and characterize the properties of raw material for standard clay, Lampang province. The raw materials used in the study are from local sources. They are Lampang kaolin clay (WC-1) and Lampang kaolin residual (WC-2). The characterization of raw material was analyzed by particle analyzer, X-ray fluorescence (XRF) and X-ray diffraction (XRD). The mixing ratio of standard clay as an addition Lampang kaolin clay 50-90% and Lampang kaolin residual 10-50% on physical-mechanical properties of standard clay. The properties of standard clay after firing at temperature at 1200°C were studied. The shrinkage, water absorption and bending strength of standard clay were tested. The results showed that the chemical components of 60%lampang kaolinite clay and 40% Lampang kaolin residual included of large amount of 67.47wt% Silicon oxide and 20.92wt%Aluminum oxide. The physical properties of standard clay had a shrinkage of 11.2%, water absorption of 1.9 % and bending strength of 659 kg/cm2. The standard clay produced fulfilled the requirements of Thai industrial standard (TIS 485-2542).

SIFAT FISIK DAN MEKANIK PAPAN PARTIKEL DARI LIMBAH PLASTIK JENIS HDPE (High Density Polyetylene) DAN RANTING/CABANG KARET (Hevea brasiliensis Muell.Arg)

2011 ◽  
Vol 3 (1) ◽  
pp. 7
Author(s):  
Sari Mirad Noor
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Plastic Waste ◽  
High Density ◽  
Different Types ◽  
Materials Used ◽  
The Impact

The need of log increace rapidly, mean while forest product decrease, so efficiency on wood process should be done wisely, in the other hand plastic waste is uncompossed material, become an environmental problems. This research aims to determine the impact of particles of type HDPE plastic wastes and twigs/branches of rubber on some physical and mechanical properties of wood. Physical properties have been tested for water content, density, thickness, and water absorption. Although mechanical properties tests were tough Broken/Module of Rufture (MOR) and the preservation of architecture/modulus of elasticity (MOE).     The raw materials used are polyethylene of high density of waste plastic and rubber adhesive urea formaldehyde branch branch. Experimental design used the randomized Completely Design (RCD) 5 x 4, in which each treatment became much like 5 times replicated).The treatment used is the diversity of the composition of the waste of plastic of different types of polyethylene of high density provides a significant effect on the content of water, water absorption, the density and the development of thickness. With regard to the persistence and the fracture of the arch determination not to give a significant effect.Keywords: physical and mechanical properties, particle board, HDPE plastic waste, branch/twig of  rubber.

scholarly journals Globalization’s Impact on the Usages of Imported and Local Building Materials in Jordan

2019 ◽  
Vol 8 (10) ◽  
pp. 971-975
Keyword(s):  
Design Process ◽  
Building Materials ◽  
Raw Materials ◽  
Study Data ◽  
Noticeable Increase ◽  
Materials Used ◽  
The Impact ◽  
The Relationship ◽  
Local Materials

The process of choosing building materials is an essential part of the design process. Whenever architects and interior designers start to think about a project, one of the first things they consider is the materials that will be used in the production of the project. There is little research exploring the impact of globalization on the level of using imported and local building materials in Jordan. Therefore, it is necessary to examine the impact of globalization on the level of using imported and local building materials in Jordan and explore the impact of using imported building materials on the level of using local building materials in Jordan. For the purpose of this study, data gathered about the usage of imported building materials in Jordan and analyzed to observe any drops of rises of using specific building materials. Also, this data was used to understand the most common imported building materials used. This study requires a total understanding of the relationship between globalization and building materials and their impact on the economy and the usage of imported and local building materials. comprehension of this relationship will make it possible to find solutions to integrate the use of imported building materials and local materials. Globalization impact can be observed in other sectors in Jordan. The building materials market is being affected by the phenomenon of globalization. It was found that there is a noticeable increase in imported building materials or raw materials that are needed to manufacture building materials. If the attitude toward the usage of local building materials in Jordan keep decreases and relying on imported building materials in the construction section, there will be a recession in the local building materials in Jordan. Having this recession will have a greater impact on the building materials and local factories in the long term.

Sign in / Sign up

Export Citation Format

Share Document