Effects of the Heat Carrier’s Temperature and Particle Size on the Pyrolysis of Imperata cylindrica in a Transported Bed Reactor

2014 ◽  
Vol 625 ◽  
pp. 612-615
Author(s):  
Mohd Fadhzir Ahmad Kamaroddin ◽  
Tuan Amran Tuan Abdullah ◽  
Ramli Mat ◽  
Nor Aishah Saidina Amin

The pyrolysis of Imperata Cylindrica in a transported bed reactor has been carried out using sand as heat carrier. This study is to determine the significant effect of the pyrolysis process condition for heat carrier temperature and particle size on the liquid yield and bio oil properties. Physical and chemical properties of bio-oil such as the water content, pH, viscosity and density were determined. The results showed that the heat carrier’s temperature highly affected the liquid product, yielding 2.30 to 11.89 wt.% in increasing the temperature from 450 to 600°C. The yield increased with larger particle size with 0.375 mm diameter gives maximum yield of 11.88 wt.% (600°C) but decreased gradually until 0.650 mm diameter afterwards.

2018 ◽  
Vol 3 (7) ◽  
pp. 33
Author(s):  
Asmaa Ali Mohammed Ali ◽  
Mustafa Abbas Mustafa ◽  
Kamal Eldin Eltayeb Yassin

The increasing demand for transportation fuel, due to increased urbanization, is now compounded by depleting and unstable crude oil reserves. Furthermore, the volatile market and the negative environmental impact of fossil fuels have driven the usage of biomass as a potential energy source. Of particular interest are biomass waste and baobab shells present an interesting option. The objective of this study is to produce bio oil by a fast pyrolysis process from baobab shells. The effect of reaction temperature, biomass particle size and fluidizing gas flow rate on the liquid product yield are investigated. The maximum liquid yield obtained was 36.6% at 500 OC at a N2 gas flowrate of 11.6 l/min and a particle size of less than 0.5 mm.


2020 ◽  
Vol 26 (1) ◽  
pp. 82-93
Author(s):  
Reihaneh Radmanesh ◽  
◽  
Mohsen Nabi Meybodi ◽  
Vahid Ramezani ◽  
Maryam Akrami ◽  
...  

Aims: Any pharmaceutical product made in pharmacy, hospital or factory may be contaminated with microbes. This contamination can originate from raw materials or during production. Hence, it is important to study the physical and chemical properties and stability of compounded drugs. Methods & Materials: In this study, first a specific sample of prescribed medication was ordered from 63 pharmacies in Yazd, Iran. After collecting the samples, the amount of microbial contamination, viscosity and particle size distribution and their stability were investigated and their results were compared to the standard levels. Findings: Based on the results, 31.7% of the samples had discoloration and 23.8% showed creaming phenomenon. In terms of particle size distribution, 57.1% of the samples had a 20-40 μm particle size and 49.2% had a viscosity equal to 2500-3000 centipoise. Regarding stability, 12.6% of the samples underwnet phase change at 30-40°C. About of the amount of hydroquinone in samples, 35% had acceptable amount. In 23.8% of the samples, fungal infection was observed. Conclusion: Contrary to a popular belief that the compounded medicines produced in pharmacies have microbial contamination, the results of this study showed that the microbial contamination of these compounded medications is low.


2018 ◽  
Vol 154 ◽  
pp. 01036 ◽  
Author(s):  
Bachrun Sutrisno ◽  
Arif Hidayat

The palm oil industry is currently growing rapidly and generating large amounts of biomass waste that is not utilized properly. Palm empty fruit bunch (PEFB), by product of palm oil industry is considered as a promising alternative and renewable energy source that can be converted to a liquid product by pyrolysis process. In this work, pyrolysis of PEFB was studied to produce bio-oil. Pyrolysis experiments were carried out in a bench scale tubular furnace reactor. The effects of pyrolysis temperatures (400–600 °C) at heating rate of 10 °C/min to optimize the pyrolysis process for maximum liquid yield were investigated. The characteristics of bio-oil were analyzed using FTIR and GC–MS. The results showed that the maximum bio-oil yield was 44.5 wt. % of the product at 450 °C. The bio-oil products were mainly composed of acids, aldehydes, ketones, alcohols, phenols, and oligomers. The chemical characterization showed that the bio-oil obtained from PEFB may be potentially valuable as a fuel and chemical feedstock.


2018 ◽  
Vol 775 ◽  
pp. 359-364
Author(s):  
Shariff Ibrahim ◽  
Siti Noor Inani Binti Baharuddin ◽  
Borhanuddin Ariffin ◽  
Megat Ahmad Kamal Megat Hanafiah ◽  
Nesamalar Kantasamy

Cogon grass (Imperata cylindrica), an invasive, unwanted grass was used and evaluated for its applicability for the sorption of engine oil. Other than dried and ground for smaller size, no notable treatment was performed on the cogon grass. The physical and chemical properties of cogon grass were characterized by ash content, bulk density, pH slurry, and Field Emission Scanning Electron Microscopy (FESEM). The oil sorption was performed in a batch adsorption system. The effects of contact time, dosage of adsorbent and oil retention were investigated. The bulk density and ash content of the prepared carbon was 0.34 g/ml and 7.80 %, respectively. The pH slurry value was near neutrality (6.48). FESEM micrograph of cogon grass showed jagged and rough surface. FTIR spectra revealed the presence of aromatic rings of lignin and some aromatic compounds associated with CH. Carbon, hydrogen and nitrogen (CHN) analysis revealed that 41% of cogon grass consists of carbon. The cogon grass was observed to wet oil almost instantly with sorption equilibrium time of 5 min. The dose of cogon grass was found to slightly affect the sorption capacity. Oil retention experiments reveal the good ability of cogon grass to hold oil with about 96% retention after 24 h dripping. This study may provide an insight on the usefulness of cogon grass for removal of engine oils.


2019 ◽  
Vol 58 (1) ◽  
pp. 179-188 ◽  
Author(s):  
Yong-Sik Chu ◽  
Batmunkh Davaabal ◽  
Dae-Sung Kim ◽  
Sung-Kwan Seo ◽  
Yoo Kim ◽  
...  

Abstract The effect of two different milling devices, namely attrition mill versus vibration mill, on the reactivity of fly ash was studied. High calcium fly ash from 4th Thermal power station of Ulaanbaatar (Mongolia) was used for the experiments. The raw and processed samples were characterized by XRD, SEM, Particle size distribution, BET, Blaine surface area and density measurements. The efficiency of 1 hour milling was evaluated with the Blaine surface area set to be more than 5000 cm2/g. The physical and chemical properties of the attrition milled fly ash changed not much compared to the vibration milled samples. For example the d50 particle size became reduced from 29 µm to 6 µm by attrition milling and in vibration milled fly ash it was reduced to 7 µm. The density increased from 2.44 g/cm3 of raw fly ash to 2.84 g/cm3 and 2.79 g/cm3 in attrition and vibration milled samples, respectively. Mechanical milling revealed not only a particle size reduction but also the formation of a denser microstructure. As a result the vibration milled fly ash showed a weaker interaction with the alkaline solution (8 M NaOH used here) compared to the attrition milled fly ash. Consequently, compressive strength of the binder prepared using the attrition milled fly ash was higher, 61 MPa, while for vibration milled fly ash it was 49 MPa. For comparison unmilled fly ash, it was 21 MPa.


1993 ◽  
Vol 23 (5) ◽  
pp. 941-955 ◽  
Author(s):  
K. Van Cleve ◽  
C.T. Dyrness ◽  
G.M. Marion ◽  
R. Erickson

Alluvial soils on the Tanana River floodplain near Fairbanks, Alaska, were examined for development of physical and chemical properties in relation to soil depth and across a 200-year vegetation development sequence. Development was mediated by ecosystem controls including successional time, vegetation, terrace height, soil physical and chemical properties, and microclimate. These controls interact and are conditioned by the state factors time, flora, topography, parent material, and climate, respectively. On early-successional (<5 years) lower alluvial surfaces, terrace height above groundwater, soil particle size, and microclimate (through soil surface evaporation) interacted through capillary rise to produce salt-affected surface soil. Calcium salts of carbonate and sulfate were the principal chemicals encountered in these soils. Establishment of a vegetation cover between 5 and 10 years introduced evapotranspiration as a new mechanism, along with capillarity, to control moisture suction gradients. In addition, newly formed surface litter layers further helped eliminate evaporation and formation of high salt content surface soil. Continued sedimentation raised terrace elevation, so on older terraces only infrequent flood events influenced soil development. Moreover, in these successional stages, only the highest river stages raised groundwater levels, so transpiration and capillarity influenced water movement to tree root systems. During the first 25–30 years of succession, plant deposition of organic matter and nitrogen, associated with the growth of alder, markedly changed soil properties. Nearly 60% (or 240 g•m−2) of the 400 g•m−2 nitrogen encountered at 100 years was accumulated during this early period. After 100 years of vegetation development, soil carbonate content dropped to about half the peak values of about 1600 g•m−2 encountered between 4 and 25 years. By the time white spruce was the dominant forest type at 180 years, carbonate carbon declined to about 500 g•m−2, one-third that of the 1600 g•m−2 high. By this time surface soil pH declined from high values of 7.5 to between 5.5 and 6.0. Organic carbon continued to accumulate to about 6300 g•m−2 in the white spruce stage, twice that encountered in the alder–poplar stage at 25 years. Indices of moisture retention were most strongly related to either soil particle size (low moisture tension and available moisture range) or vegetation-mediated soil organic matter content (high moisture tension). Cation exchange capacity was most strongly related to a vegetation-mediated index of organic matter (OM) content (%N, %C, or %OM).


Author(s):  
Lyvia Menezes ◽  
Paulo Suarez ◽  
Grace Ghesti

According to the waste-to-energy (WTE) valorization and circular economy principles, the use of waste oil and grease (WOG) for obtaining biofuels shows the tendency towards sustainability, makes the interest in green chemistry, and the development of environmentally friendly processes grow. Three different fatty wastes (from the fat trap of a sewage station, lard waste, and frying oil) were analyzed and this work showed they have no potentially toxic metals. The frying oil sample and residual lard waste showed a higher percentage of triacylglycerides resulting in higher biodiesel conversion. The samples showed physical and chemical properties (density, viscosity, and ash) within the limits established by current regulations. Bio-oil samples formed a mixture of carboxylic acids, with high acidity. However, the parameters that deviated from the maximum permitted by the standard could be adjusted blending with petroleum diesel, replacing partially the fossil energy carriers with biomass-derived energy carriers which could bring positive impacts from multiple perspectives, i.e., economic, environmental, and health.


Author(s):  
S. T. Patil ◽  
U. S. Kadam ◽  
M. S. Mane ◽  
D. M. Mahale ◽  
J. S. Dhekale

From the reviewed literature, it is observed that scientist’s worked on the various substrate medias used for hydroponic system. They also studied about different combinations of the media and their effect on crop growth. The reviewed literature shows that scientists have studied different organic and inorganic media viz. cocopit, saw dust, rice husk vermiculite, perlite, hydroton, pumice, sand etc. It was also found that these media are not easily, cheaply and locally available for users. Beside this, few scientists studied about physical and chemical properties of media such as particle size, porosity, bulk density, wettability, water holding capacity (WHC), Air filled porosity (AFP), Electrical conductivity, pH of these media. The crop specific suitability of combinations of the different media mixtures were also tested and reported by many scientists. It was revealed from reviewed literature that salinity of media caused linear reduction in the water consumption. The size and shape of particle size distribution are useful for estimating the hydraulic properties of the media The substrate under long cultivation period causes increase of organic matter content and microorganism activity which leads to an increased competition for oxygen in the root environment. The optimal EC levels range from 1.5 to 4.0 dSm-1 according to crop and its sensitivity to different salinity levels. It was also observed that level of growing medium temperature close to that of the surrounding air seems more suitable. The ideal substrate should have a total porosity of over 85 percent. Particles of smaller-sized individual grains have a larger specific surface area.


Sign in / Sign up

Export Citation Format

Share Document