Grafting Polypropylene under Ultrasonic in Water Suspension System

2015 ◽  
Vol 1095 ◽  
pp. 746-750
Author(s):  
Shuang Zhang ◽  
Bao Dong Zhu ◽  
Qing Ming Meng ◽  
Na Li ◽  
Jian Wang
Keyword(s):  
Contact Angles ◽  
Suspension System ◽  
Ultrasonic Frequency ◽  
Surface Polarity ◽  
Water Contact ◽  
Melt Flow Rate ◽  
Water Suspension ◽  
Swell Ratio ◽  
Grafting Ratio ◽  
Short Time

Polypropylene (PP) was grafted with styrene (ST), maleic anhydride (MAH) and butyl acrylate (BA) by free radical thermal initiation leading to (PP-g-PSMB) in water suspension system. The effects of ultrasonic frequency and time were investigated on PP grafting ratio in swelling stage. The structure of grafted product was analyzed by FTIR and melt flow rate (MFR), die swell ratio (Dr) and water contact angles of the grafted product were tested. The results show that the grafting ratio of PP can be improved in a short time by using ultrasonic significantly. The grafting ratio of PP increased with the increase of ultrasonic frequency. Ternary-monomer was grafted onto the PP chain branching in the form of long chain uniformly. The surface polarity of the grafted product was improved significantly.

scholarly journals Functionalized branched EDOT-terthiophene copolymer films by electropolymerization and post-polymerization “click”-reactions

2015 ◽  
Vol 11 ◽  
pp. 335-347 ◽  
Author(s):  
Miriam Goll ◽  
Adrian Ruff ◽  
Erna Muks ◽  
Felix Goerigk ◽  
Beatrice Omiecienski ◽  
...  
Keyword(s):  
Energy Levels ◽  
Contact Angles ◽  
Redox Properties ◽  
Dipolar Cycloaddition ◽  
Surface Polarity ◽  
Water Contact ◽  
Click Reactions ◽  
Copolymer Films ◽  
Post Functionalization

The electrocopolymerization of 3,4-ethylenedioxythiophene (EDOT) with the branched thiophene building block 2,2′:3′,2″-terthiophene (3T) is presented as a versatile route to functional polymer films. Comparisons to blend systems of the respective homopolymers PEDOT and P3T by in situ spectroelectrochemistry and Raman spectroscopy prove the successful copolymer formation and the access to tailored redox properties and energy levels. The use of EDOT-N3 as co-monomer furthermore allows modifications of the films by polymer analogous reactions. Here, we exemplarily describe the post-functionalization with ionic moieties by 1,3-dipolar cycloaddition (“click”-chemistry) which allows to tune the surface polarity of the copolymer films from water contact angles of 140° down to 40°.

scholarly journals The Effect of Hydroxyl on the Superhydrophobicity of Dodecyl Methacrylate (LMA) Coated Fabrics through Simple Dipping-Plasma Crosslinked Method

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1263
Author(s):  
Liyun Xu ◽  
Yu Zhang ◽  
Ying Guo ◽  
Ruiyun Zhang ◽  
Jianjun Shi ◽  
...  
Keyword(s):  
Thermoplastic Polyurethane ◽  
Hydrophobic Effect ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Binding Property ◽  
Interesting Phenomenon ◽  
Water Contact ◽  
Capacitively Coupled ◽  
Pet Fabric ◽  
Dodecyl Methacrylate

In order to obtain stable superhydrophobicity, suitable hydrophobic treatment agents should be selected according to different material properties. In this paper, cotton and poly(ethylene terephthalate) (PET) fabrics were respectively coated with dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of the treated cotton and polyester fabrics are also discussed. An interesting phenomenon happened, whereby the LMA-coated cotton fabric (Cotton-g-LMA) had better water repelling and mechanical durability properties than LMA-coated PET fabric (PET-g-LMA), and LMA-coated hydroxyl-grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG & LMA) had a similar performance to cotton fabrics. The water contact angles of Cotton-g-LMA, PET-g-LMA and PET-g-PEG & LMA were 156°, 153° and 155°, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding water contact angles decreased to 145°, 88°, 134° and 146°, 127° and 143°, respectively. Additionally, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics all exhibited the same properties as the PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively, without changing the wearing comfort.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals Physico-Chemical Characterization and Antimicrobial Properties of Hybrid Film Based on Saponite and Phloxine B

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 325
Author(s):  
Nitin Chandra teja Dadi ◽  
Matúš Dohál ◽  
Veronika Medvecká ◽  
Juraj Bujdák ◽  
Kamila Koči ◽  
...  
Keyword(s):  
Hybrid Film ◽  
Antimicrobial Properties ◽  
Chemical Characterization ◽  
Layered Silicate ◽  
Contact Angles ◽  
Exchange Capacity ◽  
Resistant Bacteria ◽  
Hybrid Films ◽  
Water Contact ◽  
Physico Chemical

This research was aimed at the preparation of a hybrid film based on a layered silicate saponite (Sap) with the immobilized photosensitizer phloxine B (PhB). Sap was selected because of its high cation exchange capacity, ability to exfoliate into nanolayers, and to modify different surfaces. The X-ray diffraction of the films confirmed the intercalation of both the surfactant and PhB molecules in the Sap film. The photosensitizer retained its photoactivity in the hybrid films, as shown by fluorescence spectra measurements. The water contact angles and the measurement of surface free energy demonstrated the hydrophilic nature of the hybrid films. Antimicrobial effectiveness, assessed by the photodynamic inactivation on hybrid films, was tested against a standard strain and against methicillin-resistant bacteria of Staphylococcus aureus (MRSA). One group of samples was irradiated (green LED light; 2.5 h) and compared to nonirradiated ones. S. aureus strains manifested a reduction in growth from 1-log10 to over 3-log10 compared to the control samples with Sap only, and defects in S. aureus cells were proven by scanning electron microscopy. The results proved the optimal photo-physical properties and anti-MRSA potential of this newly designed hybrid system that reflects recent progress in the modification of surfaces for various medical applications.

scholarly journals Bonding of Selected Hardwoods with PVAc Adhesive

2020 ◽  
Vol 11 (1) ◽  
pp. 67
Author(s):  
Ján Iždinský ◽  
Ladislav Reinprecht ◽  
Ján Sedliačik ◽  
Jozef Kúdela ◽  
Viera Kučerová
Keyword(s):  
Adhesion Strength ◽  
Cold Water ◽  
Ph Value ◽  
Water Extract ◽  
Solid Wood ◽  
Contact Angles ◽  
Water Contact ◽  
Ph Values ◽  
Positive Tendency ◽  
The Impact

The bonding of wood with assembly adhesives is crucial for manufacturing wood composites, such as solid wood panels, glulam, furniture parts, and sport and musical instruments. This work investigates 13 hardwoods—bangkirai, beech, black locust, bubinga, ipé, iroko, maçaranduba, meranti, oak, palisander, sapelli, wengé and zebrano—and analyzes the impact of their selected structural and physical characteristics (e.g., the density, cold water extract, pH value, roughness, and wettability) on the adhesion strength with the polyvinyl acetate (PVAc) adhesive Multibond SK8. The adhesion strength of the bonded hardwoods, determined by the standard EN 205, ranged in the dry state from 9.5 MPa to 17.2 MPa, from 0.6 MPa to 2.6 MPa in the wet state, and from 8.5 MPa to 19.2 MPa in the reconditioned state. The adhesion strength in the dry state of the bonded hardwoods was not influenced by their cold water extracts, pH values, or roughness parallel with the grain. On the contrary, the adhesion strength was significantly with positive tendency influenced by their higher densities, lower roughness parameters perpendicular to the grain, and lower water contact angles.

scholarly journals Fabrication of Superhydrophobic Ti–6Al–4V Surfaces with Single-Scale Micotextures by using Two-Step Laser Irradiation and Silanization

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3816
Author(s):  
Haidong He ◽  
Risheng Hua ◽  
Xuan Li ◽  
Chunju Wang ◽  
Xuezhong Ning ◽  
...  
Keyword(s):  
Laser Irradiation ◽  
Laser Fluence ◽  
Rolling Direction ◽  
Contact Angles ◽  
Second Step ◽  
Water Contact ◽  
Single Scale ◽  
The Common ◽  
The Rich ◽  
Hierarchical Multiscale

Laser irradiation is a popular method to produce microtextures on metal surfaces. However, the common laser-produced microtextures were hierarchical (multiscale), which may limit their applicability. In this paper, a method of two-step laser irradiation, combining first-step strong ablation and sequentially second-step gentle ablation, was presented to produce micron-rough surface with single-scale microtextures. The effect of laser fluence on the Ti–6Al–4V surface morphology and wettability were investigated in detail. The morphology results revealed that the microtextures produced using this method gradually evolved from multiscale to single-scale meanwhile from microprotrusions to microholes with increasing the second-step laser fluence from 0.0 to 2.4 J/cm2. The wettability and EDS/XPS results indicated that attributing to the rich TiO2 content and micron roughness produced by laser irradiation, all the two-step laser-irradiated surfaces exhibited superhydrophilicity. In addition, after silanization, all these superhydrophilic surfaces immediately turned to be superhydrophobic with close water contact angles of 155–162°. However, due to the absence of nanotextures, the water-rolling angle on the superhydrophobic surfaces with single-scale microtextures distinctly larger than those with multiscale ones. Finally, using the two-step laser-irradiation method and assisted with silanization, multifunctional superhydrophobic Ti–6Al–4V surfaces were achieved, including self-cleaning, guiding of the water-rolling direction and anisotropic water-rolling angles (like the rice-leaf), etc.

scholarly journals P4VP Modified Zwitterionic Polymer for the Preparation of Antifouling Functionalized Surfaces

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 706 ◽  
Author(s):  
Chaoqun Wu ◽  
Yudan Zhou ◽  
Haitao Wang ◽  
Jianhua Hu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Cell Attachment ◽  
Raft Polymerization ◽  
Polymer Brush ◽  
Contact Angles ◽  
Polymerization Process ◽  
Water Contact ◽  
Zwitterionic Polymers ◽  
Ito Glass ◽  
Zwitterionic Polymer

Zwitterionic polymers are suitable for replacing poly(ethylene glycol) (PEG) polymers because of their better antifouling properties, but zwitterionic polymers have poor mechanical properties, strong water absorption, and their homopolymers should not be used directly. To solve these problems, a reversible-addition fragmentation chain transfer (RAFT) polymerization process was used to prepare copolymers comprised of zwitterionic side chains that were attached to an ITO glass substrate using spin-casting. The presence of 4-vinylpyridine (4VP) and zwitterion chains on these polymer-coated ITO surfaces was confirmed using 1H NMR, FTIR, and GPC analyses, with successful surface functionalization confirmed using water contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) studies. Changes in water contact angles and C/O ratios (XPS) analysis demonstrated that the functionalization of these polymers with β-propiolactone resulted in hydrophilic mixed 4VP/zwitterionic polymers. Protein adsorption and cell attachment assays were used to optimize the ratio of the zwitterionic component to maximize the antifouling properties of the polymer brush surface. This work demonstrated that the antifouling surface coatings could be readily prepared using a “P4VP-modified” method, that is, the functionality of P4VP to modify the prepared zwitterionic polymer. We believe these materials are likely to be useful for the preparation of biomaterials for biosensing and diagnostic applications.

scholarly journals Upcycling of Vine Shoots: Production of Fillers for PHBV-Based Biocomposite Applications

2020 ◽  
Author(s):  
Grégoire David ◽  
Laurent Heux ◽  
Stéphanie Pradeau ◽  
Nathalie Gontard ◽  
Hélène Angellier-Coussy
Keyword(s):  
Water Vapor ◽  
Gas Phase ◽  
Mechanical Performance ◽  
Low Cost ◽  
Water Vapor Permeability ◽  
Contact Angles ◽  
Vapor Permeability ◽  
Water Contact ◽  
Median Diameter ◽  
Cost Of Materials

Abstract This paper aims at investigating the potential of vine shoots (ViSh) upcycling as fillers in novel poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) based biocomposites. ViSh particles of around 50 µm (apparent median diameter) were obtained combining dry grinding processes, and mixed with PHBV using melt extrusion. Thermal stability and elongation at break of biocomposites were reduced with increasing contents of ViSh particles (10, 20 and 30 wt%), while Young’s modulus and water vapor permeability were increased. It was shown that a surface gas-phase esterification allowed to significantly increase the hydrophobicity of ViSh particles (increase of water contact angles from 59° to 114°), leading to a reduction of 27% in the water vapor permeability of the biocomposite filled with 30 wt% of ViSh. The overall mechanical performance was not impacted by gas-phase esterification, demonstrating that the interfacial adhesion between the virgin ViSh particles and the PHBV matrix was already good and that such filler surface treatment was not required in that case. It was concluded that ViSh particles can be interestingly used as low cost fillers in PHBV-based biocomposites to decrease the overall cost of materials.

scholarly journals Experimental and simulation-based analysis of asymmetrical spherical roller bearings as main bearings for wind turbines

2021 ◽  
Author(s):  
Amin Loriemi ◽  
Georg Jacobs ◽  
Sebastian Reisch ◽  
Dennis Bosse ◽  
Tim Schröder
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Measurement Data ◽  
Contact Angles ◽  
Suspension System ◽  
Roller Bearings ◽  
Axial Forces ◽  
Wind Turbine System ◽  
Bearing Life ◽  
The Individual

AbstractSymmetrical spherical roller bearings (SSRB) used as main bearings for wind turbines are known for their high load carrying capacity. Nevertheless, even designed after state-of-the-art guidelines premature failures of this bearing type occur. One promising solution to overcome this problem are asymmetrical spherical roller bearings (ASRB). Using ASRB the contact angles of the two bearing rows can be adjusted individually to the load situation occurring during operation. In this study the differences between symmetrical and asymmetrical spherical roller bearings are analyzed using the finite element method (FEM). Therefore, FEM models for a three point suspension system of a wind turbine including both bearings types are developed. These FEM models are validated with measurement data gained at a full-size wind turbine system test bench. Taking into account the design loads of the investigated wind turbine it is shown that the use of an ASRB leads to a more uniform load distribution on the individual bearing rows. Considering fatigue-induced damage an increase of the bearing life by 62% can be achieved. Regarding interactions with other components of the rotor suspension system it can be stated that the transfer of axial forces into the gearbox is decreased significantly.

Laboratory and Field Data on Chlorinated Polyether Coatings Produced by Water Suspension System

CORROSION ◽  
1961 ◽  
Vol 17 (11) ◽  
pp. 32-35 ◽  
Author(s):  
O. J. Britton ◽  
W. A. Carlson ◽  
J. R. Little
Keyword(s):  
Field Data ◽  
Suspension System ◽  
Water Suspension
Sign in / Sign up

Export Citation Format

Share Document