The Effects of Sliding Parameters on Dry Wear Characteristics of Ti-6Al-4V Alloy

2015 ◽  
Vol 1115 ◽  
pp. 213-216 ◽  
Author(s):  
Mohammed Baba Ndaliman ◽  
Katsina Christopher Bala ◽  
Ahsan Ali Khan ◽  
Mohammad Yeakub Ali ◽  
Umma Abdullahi ◽  
...  
Keyword(s):  
Wear Rate ◽  
Wear Behavior ◽  
Weight Ratio ◽  
High Strength ◽  
Surface Wear ◽  
Wear Properties ◽  
Wear Rates ◽  
Sliding Motion ◽  
Study Results ◽  
Pin On Disk

Titanium (Ti-6Al-4V) alloy is very attractive for many applications due to its high strength-to-weight ratio and high corrosion resistance. Even then, with these attractive properties, it has poor shear strength and surface wear properties. This study is therefore undertaken to investigate the effect of sliding parameters on the surface wear behavior of Ti-6Al-4V alloy. Pin-like specimens of the alloy were produced and subjected to sliding motion on a pin-on-disk apparatus using different speeds, loads and sliding distances. The surface and specific wear rates of the alloy were evaluated as the main output of the study. Results indicate that the most severe surface wear rate of over 0.008 mm3/sec is experienced under conditions of low disk speed (50 rpm) with high input weight (46.5 N). Higher sliding distance is also found to affect the severity of the surface wear rate. All results of specific wear rates evaluated indicate that Ti-6Al-4V alloy can be classified as a low surface wear resistance material when operated under sliding counterface.

scholarly journals Tribological Investigations of PVD Coated Multi-Layer Constructions

2015 ◽  
Vol 5 (1) ◽  
pp. 97 ◽  
Author(s):  
Marcus Schulze ◽  
Holger Seidlitz ◽  
Franziska Konig ◽  
Sabine WeiB
Keyword(s):  
Carbon Fibre ◽  
Physical Vapor Deposition ◽  
Large Scale ◽  
Metal Cutting ◽  
Wear Behavior ◽  
Cutting Tools ◽  
Weight Ratio ◽  
High Strength ◽  
Coating System ◽  
Wear Rates

<p class="1Body">Multi-layer constructions become more and more relevant in lightweight applications due to their high strength to weight ratio. They offer excellent crash, damping and recycling properties. Also, the morphology of thermoplastic carbon fibre reinforced plastics (CFRP) render them interesting for large scale manufacturing processes. Nevertheless, a major disadvantage results in a poor resistance against wear and tear, e.g. erosion, which is attributed to weak hardness properties. Hence, this work deals with tribological investigations on orthotropic carbon fibre reinforced polymers (PA 6) either with protective ceramic coating or without. The chosen coating system is a well-known protective covering of metal components, e.g. metal cutting tools, produced by physical vapor deposition (PVD). To characterize the coating system on thermoplastic CFRP, standard analyzing methods are utilized, like optical and scanning electron microscopy (SEM). The tribological investigations are conducted by the tribological ball on disk method to generate wear tracks on the sample surfaces and hence to calculate the wear rates. These results are compared to literature findings with respect to a certain protective coating system (TiN) and a second nano-structured gel coating system, where both systems are deposited on a thermosetting material, i.e. carbon fibre reinforced epoxy resin, respectively. For this purpose the feasibility of depositing a protective ceramic layer on thermoplastic CFRP is demonstrated. First results on suitable surface pre-treatments have shown a significant influence on the coating quality. The improved performance regarding the wear behavior with respect to tribology compared to the poor substrate and existing technologies is shown additionally.</p>

Surface Wear Anisotropy in AlSi10Mg Alloy Sample Fabricated by Selective Laser Melting: Effect of Hatch Style, Scan Rotation and Use of Fresh and Recycled Powder

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Ashish Kumar Mishra ◽  
Ram Krishna Upadhyay ◽  
Arvind Kumar
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Selective Laser Melting ◽  
Wear Behavior ◽  
Alloy Sample ◽  
Surface Wear ◽  
Wear Properties ◽  
Laser Melting ◽  
Pattern Size ◽  
Scan Pattern

Abstract Additive manufacturing (AM) has witnessed substantial growth in recent years due to its excellent manufacturing capabilities and innovative production methodologies. However, the mechanical suitability aspect in terms of material wear has not received much attention yet and needs rigorous assessment. This study investigates the wear anisotropy in an AlSi10Mg alloy sample fabricated by selective laser melting (SLM) technique. Different scanning strategies encompassing the island and the continuous scanning patterns were used in sample manufacturing. The effects of the scanning vector orientation, design pattern, and the island pattern size on the mechanical wear and wear anisotropy have been analyzed in detail. The study also focused upon a comparative investigation of the wear properties at the top and the side surfaces to understand the wear anisotropy in different directions. The samples are fabricated both by the fresh and the recycled powder and the role of powder state is described. The ball-on-disk test is performed to simulate the similar contact applications for marine/automotive components such as bearings. Bearing steel balls are used as a standard sliding counterpart material to investigate the wear properties. The wear microstructure is analyzed by scanning electron microscopy. Overall, the island strategy with 2 mm hatch style and 45 deg scan rotation have achieved better wear resistance and friction coefficient compared with the continuous hatch style. The wear behavior is found to be anisotropic. The Raman spectra validate the presence of silicon and carbon particles on the wear track, which have a significant effect on the tribological properties. The type of particles present in the sliding zone characterizes different wear stages. Wear mechanism is described by considering four parameters, namely, scan pattern, scan vector rotation, type of powder, and the wear measurement direction. Results show that the surface wear rate of samples made by the fresh powder is lower than the recycled powder. However, samples of the recycled powder have friction modifier characteristics. The best wear rate and friction coefficient values are obtained with the island strategy (2 mm hatch, 45 deg scan rotation) in the side plane and are 3.76 × 10−6 mm3/N m, 0.0781, respectively.

Effect of Cooling Rate and Aging Process on Wear Behavior of Deformed TC21 Ti-Alloy

2020 ◽  
Vol 835 ◽  
pp. 265-273
Author(s):  
Ramadan N. Elshaer ◽  
Khaled M. Ibrahim ◽  
Ibrahim Lotfy ◽  
Mahmoud Abdel-Latif
Keyword(s):  
Wear Rate ◽  
Cooling Rate ◽  
Wear Behavior ◽  
Solution Treatment ◽  
Weight Ratio ◽  
High Strength ◽  
Air Cooling ◽  
Aerospace Applications ◽  
Treatment Techniques ◽  
Solution Treated

TC21 with a composition of Ti-6Al-3Mo-1.9Nb-2.2Sn-2.2Zr-1.5Cr is considered a new titanium alloy that is used in aerospace applications as a replacement for the famous Ti-6Al-4V alloy due to its high strength-to-weight ratio, high operating temperature and corrosion resistance. In this study, two different solution treatment techniques were applied on TC21 samples. Solution treatment was applied using two step heating at 1000/800 °C for 15 min each and then cooled using water quenching or air cooling to see the effect of cooling rate on microstructure as well as mechanical properties. The solution treated samples were divided into two groups; one was tested as solution treated samples without aging. While, the second group was aged at 575 °C for 4 hrs. Maximum hardness of 442 HV was observed for the water quenched and aged samples, while the minimum hardness of 340 HV was obtained for water quenched samples without aging. The lowest wear rate was obtained for water quenched and aged samples. However, the highest wear rate was reported for the samples solution treated and water quenched without aging.

Wear Behavior of Pure Titanium Coated With WC-Co by the Use of Electrospark Deposition Method

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Seyyed Jaber Razavi Arab ◽  
Hossein Aghajani
Keyword(s):  
Wear Resistance ◽  
Wear Behavior ◽  
Pure Titanium ◽  
Weight Ratio ◽  
High Strength ◽  
Deposition Process ◽  
Deposition Method ◽  
Electrospark Deposition ◽  
Substrate Properties ◽  
Pin On Disk

Titanium is a highly interesting material in engineering because of its unique combination of high strength to weight ratio, excellent resistance to corrosion, and biocompatibility. However, the material’s low wear resistance, which is its inherent nature, limits its application in highly erosive conditions. In order to enhance the wear resistance of biomedical grade titanium with the help of a WC-Co coating, an electrospark deposition method was used in this work. The goal of this work is to investigate the effect of frequency and current upper limit in the electrospark deposition process on substrate properties. Hardness of the layers was measured by a microhardness tester. In order to study the morphology and microstructure of surface layers, scanning electron microscope was used. Tribological tests were conducted under technically dry friction conditions at a load of 12.5 N by a pin-on-disk tribometer. Titanium was observed in coating and metallurgical bonding between the coating and the substrate. The optimized sample's hardness was about 930 HV 0.1. Results showed that the presence of a carbide layer on the surface of titanium leads to a great enhancement of wear resistance of about 68% in the pin-on-disk test.

scholarly journals Can Pin-on-Disk Testing Be Used to Assess the Wear Performance of Retrieved UHMWPE Components for Total Joint Arthroplasty?

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Steven M. Kurtz ◽  
Daniel W. MacDonald ◽  
Sevi Kocagöz ◽  
Mariya Tohfafarosh ◽  
Doruk Baykal
Keyword(s):  
Wear Behavior ◽  
Ultrahigh Molecular Weight Polyethylene ◽  
Volumetric Wear ◽  
Wear Properties ◽  
Wear Rates ◽  
Ultrahigh Molecular Weight ◽  
Aging Conditions ◽  
Novel Method ◽  
Pin On Disk

The objective of this study was to assess the suitability of using multidirectional pin-on-disk (POD) testing to characterize wear behavior of retrieved ultrahigh molecular weight polyethylene (UHMWPE). The POD wear behavior of 25 UHMWPE components, retrieved after 10 yearsin vivo, was compared with 25 that were shelf aged for 10–15 years in their original packaging. Components were gamma sterilized (25–40 kGy) in an air or reduced oxygen (inert) package. 9 mm diameter pins were fabricated from each component and evaluated against CoCr disks using a super-CTPOD with 100 stations under physiologically relevant, multidirectional loading conditions. Bovine serum (20 g/L protein concentration) was used as lubricant. Volumetric wear rates were found to vary based on the aging environment, as well as sterilization environment. Volumetric wear rates were the lowest for the pins in the gamma inert, shelf aged cohort. These results support the utility of using modern, multidirectional POD testing with a physiologic lubricant as a novel method for evaluating wear properties of retrieved UHMWPE components. The data also supported the hypothesis that wear rates of gamma-inert liners were lower than gamma-air liners for both retrieved and shelf aging conditions. However, this difference was not statistically significant for the retrieved condition.

Effect of High Temperature on Wear Behavior of Stir Cast Aluminium/Boron Carbide Composites

2020 ◽  
Vol 22 (4) ◽  
pp. 1031-1046
Author(s):  
X. Canute ◽  
M. C. Majumder
Keyword(s):  
High Temperature ◽  
Wear Rate ◽  
Boron Carbide ◽  
Wear Behavior ◽  
Base Alloy ◽  
Weight Fraction ◽  
Sliding Velocity ◽  
Wear Properties ◽  
High Temperature Wear ◽  
The Matrix

AbstractThe need for development of high temperature wear resistant composite materials with superior mechanical properties and tribological properties is increasing significantly. The high temperature wear properties of aluminium boron carbide composites was evaluated in this investigation. The effect of load, sliding velocity, temperature and reinforcement percentage on wear rate was determined by the pin heating method using pin heating arrangement. The size and structure of base alloy particles change considerably with an increase of boron carbide particles. The wettability and interface bonding between the matrix and reinforcement enhanced by the addition of potassium flurotitanate. ANOVA technique was used to study the effect of input parameters on wear rate. The investigation reveals that the load had higher significance than sliding velocity, temperature and weight fraction. The pin surface was studied with a high-resolution scanning electron microscope. Regression analysis revealed an extensive association between control parameters and response. The developed composites can be used in the production of automobile parts requiring high wear, frictional and thermal resistance.

Sliding Wear Behavior of Remelted Al2O3-TiO2 Plasma Sprayed Coatings on Titanium

2016 ◽  
Vol 254 ◽  
pp. 231-236 ◽  
Author(s):  
Ion Dragoş Uţu ◽  
Gabriela Marginean ◽  
Iosif Hulka ◽  
Viorel Aurel Şerban
Keyword(s):  
Sliding Wear ◽  
Wear Behavior ◽  
Pure Titanium ◽  
Titanium Substrate ◽  
Atmospheric Plasma ◽  
Wear Properties ◽  
Before And After ◽  
Sprayed Coating ◽  
Pin On Disk ◽  
Sprayed Coatings

Microstructure and wear properties of the Al2O3-13.wt% TiO2 thermally sprayed coatings before and after remelting were investigated in this study. The coatings were deposited on a pure titanium substrate using the atmospheric plasma spraying (APS) process. The as-sprayed coatings were electron beam (EB) modified in order to improve their compactness and bonding strength.The effect of EB remelting on the microstructure, phase constituents and wear properties was investigated using scanning electron microscopy (SEM), X-Ray diffraction technique and hardness measurements. The sliding wear behavior was tested using a pin on disk method.The results showed that the remelting process had a positive effect removing the lamellar defect of the as-sprayed coating and improving the compactness, hardness and wear behavior.

Wear characteristics of additively manufactured AlSi10Mg against EN-31 and silicon carbide abrasive sheet counter bodies using box Behnken design approach

2021 ◽  
pp. 146442072110570
Author(s):  
Raj Mohan Radhakrishnan ◽  
Venkatraman Ramamoorthi ◽  
Raghuraman Srinivasan
Keyword(s):  
Silicon Carbide ◽  
Wear Rate ◽  
Weight Ratio ◽  
High Strength ◽  
Design Approach ◽  
Box Behnken Design ◽  
Wear Characteristics ◽  
Testing Facility ◽  
En 31 ◽  
Sliding Distance

High strength-to-weight ratio materials are used in the automotive and aerospace industries, and AlSi10Mg is suitable for those applications. The research aims to compare and investigate the wear characteristics of selective laser melted AlSi10Mg pin against two counter bodies, EN-31 hardened steel, and silicon carbide abrasive sheet. The wear rate of additively manufactured AlSi10Mg pin at 0° building orientation was investigated using the box Behnken design approach to identify the suitable wear parameters with the pin on the disc testing facility. Based on analysis of variance, the interaction of load with sliding distance significantly influenced the wear rate of AlSi10Mg in both counter body cases. The adhesion and abrasion wear mechanism were observed in AlSi10Mg with EN-31 and silicon carbide abrasive sheet, respectively. The findings reveal the effect of two counter bodies on the SLMed AlSi10Mg wear phenomenon. Finally, severe wear was observed in the AlSi10Mg pin against the silicon carbide counter body.

Investigation of the Wear Behavior of AA6082 Against Different Counterparts

2021 ◽  
Author(s):  
Safiye İpek Ayvaz ◽  
Mehmet Ayvaz
Keyword(s):  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Pin On Disk ◽  
Disk Method ◽  
Sliding Distance ◽  
Oxidation Wear

In this study, the effect of different counterparts on the wear resistance of AA6082 aluminum alloy was investigated. In tests using pin-on-disk method, 6 mm diameter Al2O3, 100Cr6 and WC-6Co balls were used as counterparts. The tests were carried out using 500 m sliding distance and 5N load. The lowest specific wear rate was measured as 7.58x10-4 mm3/Nm in WC-6Co / AA6082 couple, and the highest value was measured as 9.71x10-4 mm3/Nm in 100Cr6/AA6082 couple. In the Al2O3/AA6082 couple, the specific wear rate of the AA6082-T6 sample was determined as 8.23x10-4 mm3/Nm.While it was observed that the dominant wear type in the 100Cr6/AA6082 pair was abrasive wear, oxidation wear and oxide tribofilm were detected in the WC-6Co/AA6082 and Al2O3/AA6082 couple besides the abrasive wear.

Mechanical and Wear Behavior of Al7075 - Graphite Self-Lubricating Composite Reinforced by Nano-WO3 Particles

2020 ◽  
Vol 1002 ◽  
pp. 151-160 ◽  
Author(s):  
Anmar D. Mahdi ◽  
Saif S. Irhayyim ◽  
Salah F. Abduljabbar
Keyword(s):  
Compressive Strength ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Wear Behavior ◽  
Microstructural Analysis ◽  
Wear Test ◽  
High Strength ◽  
Hybrid Nanocomposites ◽  
Dry Sliding Wear ◽  
Alloy Matrix

Al7075 hybrid nanocomposites considered one of the most material utilized in modern engineering applications that required a combination of superior properties such as lightweight, high strength, excellent corrosion resistance, and high thermal conductivity. In the current study, Al7075 – 5 vol % graphite self-lubricating composite was reinforced by 0, 1.5, 2.5, 3.5, and 4.5 vol % WO3 nanoparticles in order to study the microstructural, mechanical, and wear characteristics. The classical powder metallurgy route was employed to fabricate the hybrid nanocomposites specimens. The microstructural analysis of the nanocomposites was characterized by utilizing a Field Emission Scanning Electron Microscope (FESEM) and Energy-Dispersive X-ray (EDX) analyses. Mechanical properties such as micro-hardness and diametral compressive strength were studied. Dry sliding wear test was performed under the various loads of 10, 15, 20, and 25 N at a sliding distance and sliding speed of 1810 m and 1.5 m/s, respectively. Results have revealed that the microhardness and diametral compressive strength considerably improved by increasing the WO3 content until 3.5 vol % and then slightly decreased. Besides, both the values of the wear rate and friction coefficient gradually reduced by increment the reinforcement content up to 3.5 vol % and then suddenly increases for all the applied loads. Nevertheless, the wear rate and friction coefficient were correlated positively with the applied loads. From the results obtained, graphite as solid lubricating material with WO3 nanoparticles was successfully combined into the Al7075 alloy matrix. The optimum mechanical and wear performance of the hybrid nanocomposite were revealed at 3.5 vol % content of WO3 nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document