Preparation and Characterization of Al-Mg-B Thin Films by Magnetron Sputtering

2012 ◽  
Vol 465 ◽  
pp. 112-117 ◽  
Author(s):  
Wen Liu ◽  
Qing Sen Meng ◽  
Yang Miao ◽  
Feng Hua Chen ◽  
Li Fang Hu
Keyword(s):  
Thin Films ◽  
Sputter Deposition ◽  
X Ray Diffraction ◽  
Space Applications ◽  
X Ray ◽  
Atomic Force ◽  
Sputtering Power ◽  
Target Power

Hard and superlight thin films laminated with boron carbide have been proposed as candidates for strategic use such as armor materials in military and space applications. We prepared Al-Mg-B films by sputter deposition on Si (100) substrates with one AlMgB14 target. The films were characterized by X-ray diffraction, atomic force microscope, GD-OES spectroscopy. The results show that films of AlMgB with different compositions have been deposited by changing the target power and deposition temperature.The influences of substrate temperature and sputtering power on the quality of the films are discussed.

Growth and Characterization of (012)- and (001)-Oriented Epitaxial Anatase Thin Films

2006 ◽  
Vol 46 ◽  
pp. 146-151
Author(s):  
Andriy Lotnyk ◽  
Stephan Senz ◽  
Dietrich Hesse
Keyword(s):  
Thin Films ◽  
Cross Section ◽  
Single Phase ◽  
Electron Beam Evaporation ◽  
X Ray Diffraction ◽  
Tio2 Thin Films ◽  
X Ray ◽  
Transmission Electron

Single phase TiO2 thin films of anatase structure have been prepared by reactive electron beam evaporation. Epitaxial (012)- and (001)-oriented anatase films were successfully obtained on (110)- and (100)-oriented SrTiO3 substrates, respectively. X-ray diffraction and cross section transmission electron microscopy investigations revealed a good epitaxial quality of the anatase films grown on the SrTiO3 substrates.

Microstructure and Properties of TiO2 Thin Films Doped with Ni

2012 ◽  
Vol 490-495 ◽  
pp. 3306-3310
Author(s):  
Fei Gao ◽  
Xiao Yan Liu ◽  
Li Yun Zheng ◽  
Mei Xia Li ◽  
Rui Jiao Jiang
Keyword(s):  
Thin Films ◽  
Anatase Phase ◽  
X Ray Diffraction ◽  
Tio2 Thin Films ◽  
Ni Doping ◽  
X Ray ◽  
Force Microscopy ◽  
Microstructure And Properties ◽  
Atomic Force ◽  
Sputtering Power

TiO2 and Ni-doped TiO2 thin films were prepared by DC magnetron sputtering. The effects of Ni-doping on the microstructure and properties were studied by atomic force microscopy (AFM), X-ray diffraction (XRD), UV-Vis spectra and photocatalysis tesing, respectively. The results show that TiO2 thin films were successfully prepared with smooth surface. When doped with Ni, the surface of TiO2 thin film was improved and the growth of anatase phase was also promoted. With increasing the sputtering power of Ni, the absorption edge wavelegth red shifted and the photocatalysis property of TiO2 thin films was increased and then decreased

Nanocrystalline Solutions as Precursors to The Spray Deposition of Cdte Thin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
Martin Pehnt ◽  
Douglas L. Schulz ◽  
Calvin J. Curtis ◽  
Helio R. Moutinho ◽  
Amy Swartzlander ◽  
...  
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Cdte Nanoparticles ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Cdte Thin Films

ABSTRACTIn this article we report the first nanoparticle-derived route to smooth, dense, phase-pure CdTe thin films. Capped CdTe nanoparticles were prepared by injection of a mixture of Cd(CH3)2, (n-C8H17)3 PTe and (n-C8H17)3P into (n-C8H17)3PO at elevated temperatures. The resultant nanoparticles 32-45 Å in diameter were characterized by x-ray diffraction, UV-Vis spectroscopy, transmission electron microscopy, thermogravimetric analysis and energy dispersive x-ray spectroscopy. CdTe thin film deposition was accomplished by dissolving CdTe nanoparticles in butanol and then spraying the solution onto SnO2-coated glass substrates at variable susceptor temperatures. Smooth and dense CdTe thin films were obtained using growth temperatures approximately 200 °C less than conventional spray pyrolysis approaches. CdTe films were characterized by x-ray diffraction, UV-Vis spectroscopy, atomic force microscopy, and Auger electron spectroscopy. An increase in crystallinity and average grain size as determined by x-ray diffraction was noted as growth temperature was increased from 240 to 300 °C. This temperature dependence of film grain size was further confirmed by atomic force microscopy with no remnant nanocrystalline morphological features detected. UV-Vis characterization of the CdTe thin films revealed a gradual decrease of the band gap (i.e., elimination of nanocrystalline CdTe phase) as the growth temperature was increased with bulk CdTe optical properties observed for films grown at 300 °C.

Characterization of Natural and Synthesized FeTiO3 Crystals With RBS/PIXE/XRD

1997 ◽  
Vol 07 (03n04) ◽  
pp. 265-275
Author(s):  
R. Q. Zhang ◽  
S. Yamamoto ◽  
Z. N. Dai ◽  
K. Narumi ◽  
A. Miyashita ◽  
...  
Keyword(s):  
Single Crystals ◽  
Ion Beam ◽  
Pressure Control ◽  
Floating Zone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Beam Analysis ◽  
Ppm Level

Natural FeTiO 3 (illuminate) and synthesized FeTiO 3, single crystals were characterized by Rutherford backscattering spectroscopy combined with channeling technique and particle-induced x-ray emission (RBS-C and PIXE). The results obtained by the ion beam analysis were supplemented by the x-ray diffraction analysis to identify the crystallographic phase. Oriented single crystals of synthesized FeTiO 3 were grown under the pressure control of CO 2 and H 2 mixture gas using a single-crystal floating zone technique. The crystal quality of synthesized FeTiO 3 single crystals could be improved by the thermal treatment but the exact pressure control is needed to avoid the precipitation of Fe 2 O 3 even during the annealing procedure. Natural FeTiO 3 contains several kinds of impurities such as Mn , Mg , Na and Si . The synthesized samples contain Al , Si and Na which are around 100 ppm level as impurities. The PBS-C results of the natural sample imply that Mn impurities occupy the Fe sublattice in FeTiO 3 or in mixed phase between ilmenite and hematite.

Optical properties of anatase TiO2 films modified by N ion implantation

2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu
Keyword(s):  
Thin Films ◽  
Ion Implantation ◽  
Photoelectron Spectroscopy ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Light Region ◽  
Uv Visible ◽  
Substrate Temperatures

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.

Characterization of WC-Co Coatings Using HP/HVOF Process

1996 ◽  
Author(s):  
S.Y. Hwang ◽  
B.G. Seong ◽  
M.C. Kim
Keyword(s):  
Wear Resistance ◽  
X Ray Diffraction ◽  
High Carbon ◽  
Properties Of Coatings ◽  
X Ray ◽  
Hvof Process ◽  
Number Of Passes ◽  
Oxygen Fuel

Abstract To maintain surface roughness of process rolls in cold rolling steel plants, WC-Co coatings have been known to be effective ones. In this study, a high pressure/high velocity oxygen fuel (HP/HVOF) process was used to obtain WC-Co coatings. To get the best quality of coatings, WC-Co coatings are sprayed with numerous powders made by various processes. These powders include agglomerated sintered powders, fused-crushed powders, extra high carbon WC-Co powders and (W2C, WC)-Co powders. After spraying, properties of coatings such as hardness, wear resistance. X-ray diffraction, and microstructures were analyzed. For coatings produced by agglomerated-sintered powders, hardness of the coating increased as power levels and the number of passes were increased. In case of the coatings produced by fused-crushed powders, a very low deposition rate was obtained due to a low flowablity of the powders. In addition, the WC-Co coatings sprayed with extra carbon content of WC-Co did not show improved hardness and wear resistance. Also, some decomposition of WC was observed in the coating. Finally, the coatings produced by (W2C, WC)-Co powders produced higher hardness and lower wear resistance coating.

Structural and Optical Characterization of Zinc Telluride Thin Films

2013 ◽  
Vol 665 ◽  
pp. 254-262 ◽  
Author(s):  
J.R. Rathod ◽  
Haresh S. Patel ◽  
K.D. Patel ◽  
V.M. Pathak
Keyword(s):  
Thin Films ◽  
Extinction Coefficient ◽  
Nir Spectroscopy ◽  
Optical Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Evaporation Technique ◽  
Film Form ◽  
Znte Thin Films

Group II-VI compounds have been investigated largely in last two decades due to their interesting optoelectronic properties. ZnTe, a member of this family, possesses a bandgap around 2.26eV. This material is now a day investigated in thin film form due to its potential towards various viable applications. In this paper, the authors report their investigations on the preparation of ZnTe thin films using vacuum evaporation technique and their structural and optical characterizations. The structural characterization, carried out using an X-ray diffraction (XRD) technique shows that ZnTe used in present case possesses a cubic structure. Using the same data, the micro strain and dislocation density were evaluated and found to be around 1.465×10-3lines-m2and 1.639×1015lines/m2respecctively. The optical characterization carried out in UV-VIS-NIR region reveals the fact that band gap of ZnTe is around 2.2eV in present case. In addition to this, it was observed that the value of bandgap decreases as the thickness of films increases. The direct transitions of the carries are involved in ZnTe. Using the data of UV-VIS-NIR spectroscopy, the transmission coefficient and extinction coefficient were also calculated for ZnTe thin films. Besides, the variation of extinction coefficient with wavelength has also been discussed here.

scholarly journals Influence of the growth parameters of TiO2 thin films deposited by the MOCVD method

Cerâmica ◽  
2002 ◽  
Vol 48 (305) ◽  
pp. 38-42 ◽  
Author(s):  
M. I. B. Bernardi ◽  
E. J. H. Lee ◽  
P. N. Lisboa-Filho ◽  
E. R. Leite ◽  
E. Longo ◽  
...  
Keyword(s):  
Thin Films ◽  
Growth Parameters ◽  
Structural Characteristics ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Tio2 Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Deposition Parameters

The synthesis of TiO2 thin films was carried out by the Organometallic Chemical Vapor Deposition (MOCVD) method. The influence of deposition parameters used during growth on the final structural characteristics was studied. A combination of the following experimental parameters was studied: temperature of the organometallic bath, deposition time, and temperature and substrate type. The high influence of those parameters on the final thin film microstructure was analyzed by scanning electron microscopy with electron dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction.

Sign in / Sign up

Export Citation Format

Share Document