The Phenotypes of Osteoblastic Cells on Surfaces with Different Mechanical Properties

2008 ◽  
Vol 47-50 ◽  
pp. 837-840
Author(s):  
Chia Bin Hung ◽  
Ming Hua Ho ◽  
Sheng Wen Hsiao
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Protein Composition ◽  
Hydrophobic Surface ◽  
Osteoblastic Differentiation ◽  
Osteoblastic Cells ◽  
Polydimethyl Siloxane ◽  
Cell Behaviors ◽  
The Difference ◽  
Substrate Surfaces

In this study, the PDMS (polydimethyl siloxane) membranes with different mechanical strength were prepared and applied for the culture of osteoblastic cells. The osteoblastic phenotypes were then analyzed, including attachment, proliferation and differentiation. Meanwhile, the hydrophilicity of membranes was also adjusted by using plasma treatment. From the preliminarily results, the osteoblastic cells would prefer to attach to the PDMS substrate with higher hardness, which also resulted in a higher cell density in cell proliferation for longer culture times. The above tendency would be only significant on the hydrophilic surface, which revealed that the cell would not well recognize the surface properties on the hydrophobic surface. The results also indicated the osteoblastic differentiation would be affected by the mechanical strength of substrate surfaces. To investigate the mechanism of the mechanical effects on cell behaviors, the protein deposition was analyzed on surfaces with different hardness. The outcome suggested that the protein composition on these surfaces would be changed due to the difference in the mechanical properties.

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

scholarly journals Goldmann Tonometry and Corneal Biomechanics

2021 ◽  
Vol 11 (9) ◽  
pp. 4025
Author(s):  
Dario Messenio ◽  
Marco Ferroni ◽  
Federica Boschetti
Keyword(s):  
Mechanical Properties ◽  
Anterior Chamber ◽  
Pressure Transducer ◽  
Pearson Correlation ◽  
Corneal Thickness ◽  
Applanation Tonometry ◽  
In Vitro Tests ◽  
Goldmann Tonometry ◽  
The Difference

Glaucoma is the second cause of irreversible blindness in the world. Intraocular pressure (IOP) is a recognized major risk factor for the development and progression of glaucomatous damage. Goldmann applanation tonometry (GAT) is internationally accepted as the gold standard for the measurement of IOP. The purpose of this study was to search for correlations between Goldmann tonometry and corneal mechanical properties and thickness by means of in vitro tests. IOP was measured by the Goldmann applanation tonometer (GIOP), and by a pressure transducer inserted in the anterior chamber of the eye (TIOP), at increasing pressure levels by addition of saline solution in the anterior chamber of enucleated pig eyes (n = 49). Mechanical properties were also determined by inflation tests. The GAT underestimated the real measurements made by the pressure transducer, with most common differences in the range 15–28 mmHg. The difference between the two instruments, highlighted by the Bland–Altman test, was confirmed by ANOVA, normality tests, and Mann–Whitney’s tests, both on the data arranged for infusions and for the data organized by pressure ranges. Pearson correlation tests revealed a negative correlation between (TIOP-GIOP) and both corneal stiffness and corneal thickness. In conclusion, data obtained showed a discrepancy between GIOP and TIOP more evident for softer and thinner corneas, that is very important for glaucoma detection.

scholarly journals High-strength and fibrous capsule–resistant zwitterionic elastomers

2021 ◽  
Vol 7 (1) ◽  
pp. eabc5442
Author(s):  
Dianyu Dong ◽  
Caroline Tsao ◽  
Hsiang-Chieh Hung ◽  
Fanglian Yao ◽  
Chenjue Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
High Strength ◽  
Design Principles ◽  
Fibrous Capsule ◽  
High Mechanical Strength ◽  
Capsule Formation ◽  
Locking Mechanism ◽  
Fibrous Capsule Formation

The high mechanical strength and long-term resistance to the fibrous capsule formation are two major challenges for implantable materials. Unfortunately, these two distinct properties do not come together and instead compromise each other. Here, we report a unique class of materials by integrating two weak zwitterionic hydrogels into an elastomer-like high-strength pure zwitterionic hydrogel via a “swelling” and “locking” mechanism. These zwitterionic-elastomeric-networked (ZEN) hydrogels are further shown to efficaciously resist the fibrous capsule formation upon implantation in mice for up to 1 year. Such materials with both high mechanical properties and long-term fibrous capsule resistance have never been achieved before. This work not only demonstrates a class of durable and fibrous capsule–resistant materials but also provides design principles for zwitterionic elastomeric hydrogels.

scholarly journals Investigation of Color Reproduction on Linen Fabrics when Printing with Mimaki TX400-1800D Inkjet with Pigment TP250 Dyes

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 354
Author(s):  
Tim Tofan ◽  
Rimantas Stonkus ◽  
Raimondas Jasevičius
Keyword(s):  
Mechanical Properties ◽  
Color Reproduction ◽  
Related Effect ◽  
Color Characteristics ◽  
Fabric Density ◽  
Different Types ◽  
The Difference ◽  
Printing Parameters ◽  
Linen Fabric

The aim of this research is to investigate related effect of dyeability to linen textiles related to different printing parameters. The study investigated the change in color characteristics when printing on linen fabrics with an inkjet MIMAKI Tx400-1800D printer with pigmented TP 250 inks. The dependence of color reproduction on linen fabrics on the number of print head passes, number of ink layers to be coated, linen fabric density, and different types of linen fabric was investigated. All this affects the quality of print and its mechanical properties. The change in color characteristics on different types of linen fabrics was determined experimentally. We determine at which print settings the most accurate color reproduction can be achieved on different linen fabrics. The difference between the highest and the lowest possible number of head passages was investigated. The possibilities of reproducing different linen fabric colors were determined.

scholarly journals The Mechanical Properties and Damage Evolution of UHPC Reinforced with Glass Fibers and High-Performance Polypropylene Fibers

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2455
Author(s):  
Jiayuan He ◽  
Weizhen Chen ◽  
Boshan Zhang ◽  
Jiangjiang Yu ◽  
Hang Liu
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Damage Evolution ◽  
High Performance ◽  
High Performance Concrete ◽  
Glass Fibers ◽  
Ultra High Performance Concrete ◽  
Concrete Damaged Plasticity ◽  
The Difference ◽  
Experimental Values

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I5, I10 and I20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

scholarly journals Mechanical strength and flexibility in $$\alpha '$$-4H borophene

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shobair Mohammadi Mozvashi ◽  
Mohammad Ali Mohebpour ◽  
Sahar Izadi Vishkayi ◽  
Meysam Bagheri Tagani
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
2D Materials ◽  
Group Iv ◽  
Good Stability ◽  
Free Standing ◽  
Promising Candidate ◽  
Inherent Anisotropy

AbstractVery recently, a novel phase of hydrogenated borophene, namely $$\alpha '$$ α ′ -4H, has been synthesized in a free-standing form. Unlike pure borophenes, this phase shows very good stability in the air environment and possesses semiconducting characteristics. Because of the interesting stiffness and flexibility of borophenes, herein, we systematically studied the mechanical properties of this novel hydrogenated phase. Our results show that the monolayer is stiffer (Y$$_\text {xy}$$ xy = $$\sim $$ ∼ 195 N/m) than group IV and V 2D materials and even than MoS$$_2$$ 2 , while it is softer than graphene. Moreover, similar to other phases of borophene, the inherent anisotropy of the pure monolayer increases with hydrogenation. The monolayer can bear biaxial, armchair, and zigzag strains up to 16, 10, and 14% with ideal strengths of approximately 14, 9, and 12 N/m, respectively. More interestingly, it can remain semiconductor under this range of tension. These outstanding results suggest that the $$\alpha '$$ α ′ -4H is a promising candidate for flexible nanoelectronics.

Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

Comparison of As-Cast Microstructures and Mechanical Properties for Mg-Ce-Mn-Sc and Mg-Ce-Mn-Zn Magnesium Alloys

2009 ◽  
Vol 610-613 ◽  
pp. 746-749 ◽  
Author(s):  
Jia Shen ◽  
Ming Bo Yang ◽  
Fu Sheng Pan ◽  
Ren Ju Cheng
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Creep Properties ◽  
Microstructures And Mechanical Properties ◽  
The Difference ◽  
Cast Microstructure

The as-cast microstructures and mechanical properties of Mg-3Ce-1.2Mn-0.9Sc and Mg-3Ce-1.2Mn-1Zn magnesium alloys were investigated and compared. The results indicate that the as-cast microstructure of Mg-3Ce-1.2Mn-0.9Sc alloy was mainly composed of -Mg, Mg12Ce and Mn2Sc phases, and that the as-cast microstructure of Mg-3Ce-1.2Mn-1Zn alloy was mainly composed of -Mg, Mg12Ce and MgZn phases. In addition, the as-cast tensile and creep properties of Mg-3Ce-1.2Mn-0.9Sc alloy were higher than that of the Mg-3Ce-1.2Mn-1Zn alloy. The difference of the two alloys in as-cast tensile and creep properties may be related to the initial microstructures of the two alloys.

Sign in / Sign up

Export Citation Format

Share Document