Processing and Mechanical Properties of Starch and PVA Composite Reinforced by Nano-SiO2

2012 ◽  
Vol 557-559 ◽  
pp. 201-204 ◽  
Author(s):  
Wen Yong Liu ◽  
Yi Chen ◽  
Xi Tu ◽  
Yue Jun Liu ◽  
Xi Hai Hao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Polyvinyl Alcohol ◽  
Weight Ratio ◽  
Weight Percent ◽  
Nano Silica ◽  
Glycerol Content ◽  
Rheological Measurements ◽  
Reinforcing Agent

The thermoplastic processing and mechanical properties of starch and polyvinyl alcohol (PVA) composites were studied. Glycerol was chosen as the plasticizer and nano-silica (nano-SiO2) as the reinforcing agent of the starch/PVA composites. The results showed that the mechanical properties of the obtained starch/PVA blend were best when the glycerol content was 30% of starch and 20% of PVA, and the weight ratio of PVA and starch was 0.8 (wPVA/ wstarch= 0.8/1). After the addition of nano-SiO2, the mechanical properties of the starch/PVA blends were improved. When the weight percent of nano-SiO2was 2%, the mechanical properties of the SiO2/starch/PVA composite were most excellent. It was shown that the tensile strength was increased by 16% and the elongation increased by 72%. Moreover, it was confirmed by rheological measurements that nano-SiO2could interact with the composite materials, which results in the improvement of the mechanical strength of the starch/PVA composites.

Processing and Mechanical Properties of Starch and PVA Composite Reinforced by MCC

2012 ◽  
Vol 583 ◽  
pp. 32-35 ◽  
Author(s):  
Wen Yong Liu ◽  
Kai Tan ◽  
Yu Gang Huang ◽  
Yi Chen ◽  
Xiang Gang Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Polyvinyl Alcohol ◽  
Mechanical Strength ◽  
Weight Ratio ◽  
Glycerol Content ◽  
Rheological Measurements

The thermoplastic processing and mechanical properties of starch and polyvinyl alcohol (PVA) composites reinforced with microcrystal cellulose (MCC) were investigated. Glycerol with 30 wt% was chosen as the plasticizer for starch and PVA, respectively. MCC with 2 wt% was used to reinforce the starch/PVA composite. The results showed that the mechanical properties of the obtained starch/PVA blend were best when the glycerol content was 30% of starch and 20% of PVA, and the weight ratio of PVA and starch was 4/6 (wPVA/wstarch). After the addition of MCC, the mechanical properties of the starch/PVA blends were improved, and the tensile strength was increased by 52%. Moreover, it was confirmed by rheological measurements that MCC could interact with the composite materials, which results in the improvement of the mechanical strength of the starch/PVA composites.

Processing and Mechanical Properties of Starch and PCL Composite Reinforced by Nano-SiO2

2012 ◽  
Vol 496 ◽  
pp. 134-137 ◽  
Author(s):  
Wen Yong Liu ◽  
Yi Chen ◽  
Long Ouyang ◽  
Yue Jun Liu ◽  
Xi Hai Hao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Mechanical Strength ◽  
Weight Percent ◽  
Nano Silica ◽  
Rheological Measurements

The thermoplastic processing and mechanical properties of starch and polycaprolactone (PCL) composites reinforced by nano-silica (nano-SiO2) were studied. The results showed that the mechanical properties of the starch/PCL blends improved significantly with the increase of PCL. After the addition of nano-SiO2, the mechanical properties of the starch/PCL blends further improved. When the weight percent of nano-SiO2 was 1.8%, the mechanical properties of the SiO2/TPS/PCL composite were most excellent. By comparison with the starch/PCL (50/50) blends, the tensile strength of the SiO2/TPS/PCL composite with 1.8% SiO2 was increased by 20% and the elongation increased by 33%. Moreover, it was confirmed by rheological measurements that nano-SiO2 could interact with the composite materials, which results in the improvement of the mechanical strength of the TPS/PCL composites.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

Influence of the Composition of Cement Mortars Modified by Lime or Polymers on the Mechanical Properties and Microstructure of Mortars

2013 ◽  
Vol 592-593 ◽  
pp. 647-650 ◽  
Author(s):  
Małgorzata Lenart
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Polyvinyl Alcohol ◽  
Polymer Composites ◽  
Adhesion Strength ◽  
Hardened Cement ◽  
Cement Mortars ◽  
Styrene Butadiene

Cement – polymer composites are nowadays widely used in repair systems not only in case of concrete or reinforced concrete constructions but also in masonry. Polymers addition for example already at 5% m.c. modifies the structure of the cement – polymer composite in a way that many of the mechanical properties such as flexural strength, tensile strength or adhesion to substrates are improved. The paper presents the results of tests such as flexural, compressive or adhesion strength to ceramic substrate of hardened cement mortars with different composition, as well as selected cement mortars modified by two polymers: polyvinyl alcohol and styrene – butadiene polymer dosed at 5 % m.c. Four types of cement mortars modified by lime (component used in historical constructions as well as in contemporary masonry mortars) are also examined for comparison.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

Research on Mechanical Properties of Modified Organic Montmorillonite Reinforced Nature Rubber(NR) Composites

2011 ◽  
Vol 239-242 ◽  
pp. 3231-3235
Author(s):  
Xiao Yu Zheng ◽  
Jin Cheng Wang ◽  
Ke Yang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Oh Groups ◽  
Abrasion Loss ◽  
Organic Montmorillonite ◽  
Reinforcing Agent

In this paper, hyperbranched organic montmorillonite (H-OMMT) with hydroxyl (-OH) groups was prepared. The organic montmorillonite (OMMT) was used as a reinforcing agent in NR matrix. The H-OMMT modified natural rubber (NR) had good mechanical properties with the addition of the H-OMMT. Properties, such as tensile strength and abrasion loss, were researched and compared. Results showed that NR/H-OMMT-5% composite had the best tensile and were resistant properties.

Effect of Heat Setting Methods on Structures and Properties of High Strength Polyvinyl Alcohol Fibre

2015 ◽  
Vol 815 ◽  
pp. 643-648
Author(s):  
Yin Zhu ◽  
Jiong Xin Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Setting Time ◽  
High Strength ◽  
Single Fibre ◽  
X Ray Diffraction ◽  
Heat Setting ◽  
Heat Treated ◽  
Setting Process

The effect of heat setting methods on the structures and mechanical properties of high strength polyvinyl alcohol (PVA) fibre is studied in this article. The microstructure and mechanical properties of heat treated PVA fibre is investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and single fibre electronic tensile strength tester. Results show that the heat setting method with constant tension is a good heat setting method which can largely enhance the tensile strength of PVA fibre. During the heat setting process, the mechanical properties of PVA fibre are greatly affected by the temperature, tension and setting time. When the temperature is 220°C, tension is 5cN/dtex and setting time is 90sec, the tensile strength of PVA fibre increases from 12.0cN/dtex to 16.4cN/dtex in compare with the PVA fibre without heat setting

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

The effect of large area graphene oxide (LAGO) nanosheets on the mechanical properties of polyvinyl alcohol

2016 ◽  
Vol 36 (4) ◽  
pp. 399-405 ◽  
Author(s):  
Khalid Nawaz ◽  
Muhammad Ayub ◽  
Noaman Ul-Haq ◽  
M.B. Khan ◽  
Muhammad Bilal Khan Niazi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Graphene Oxide ◽  
Polyvinyl Alcohol ◽  
Molecular Level ◽  
Large Area ◽  
Graphene Oxides ◽  
Elongation At Break ◽  
Graphene Oxide Sheets ◽  
Excellent Improvement

Abstract Large area graphene oxide sheets were synthesized, dispersed in water and used as nanofiller for mechanical improvement in terms of Young’s modulus and ultimate tensile strength (UTS) of polyvinyl alcohol (PVA) at low loading. The molecular level dispersion and interfacial interactions between the graphene oxides and polymeric matrix PVA were the real challenges. An excellent improvement in mechanical properties at 0.35 wt% loading was observed. Modulus improved from 1.58 GPa to 2.72 GPa (~71% improvement), UTS improved from 120 MPa to 197 MPa (~65% improvement), and in spite of these improvements, interestingly, there was no fall in elongation at break at this loading.

Sign in / Sign up

Export Citation Format

Share Document