The Analysis of Mechanical Behavior for UMo/Al Dispersion Fuel on Different Fuel Volume and Burnup

2013 ◽  
Vol 721 ◽  
pp. 184-189
Author(s):  
Xiao Liu ◽  
Da Zhi Qian ◽  
Zhi Hua Zhang ◽  
Bin Tang
Keyword(s):  
Thermal Conductivity ◽  
Mechanical Behavior ◽  
Maximum Stress ◽  
Volume Fraction ◽  
Ansys Software ◽  
Dispersion Fuel ◽  
Structure Characteristics ◽  
Unit Model ◽  
Risk Of Rupture ◽  
Irradiation Resistance

UMo/Al fuel is a typical dispersion fuel and is becoming a focus of research in many countries as it has higher density, better thermal conductivity and stronger irradiation resistance. According to the structure characteristics of dispersion nuclear fuel, the periodic unit model is established and the mechanical behavior for UMo/Al dispersion fuel on different fuel volume and burnup is simulated by ANSYS software. The results show that maximum stress occurs in the middle of fuel plate. With the fuel volume fraction increasing, the risk of rupture of fuel plate corresponding increase. It reveal the mechanism of irradiation failure for dispersion fuel plate and the results can be demonstrated by the sample figure of irradiation.

The influence of the addition of ground olive stone on the thermo-mechanical behavior of compressed earth blocks

2020 ◽  
Vol 108 (2) ◽  
pp. 203
Author(s):  
Samia Djadouf ◽  
Nasser Chelouah ◽  
Abdelkader Tahakourt
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Mechanical Behavior ◽  
Agricultural Waste ◽  
Hydraulic Press ◽  
Dry Density ◽  
Olive Stone ◽  
Compressed Earth Blocks ◽  
Clay Matrix ◽  
Earth Blocks

Sustainable development and environmental challenges incite to valorize local materials such as agricultural waste. In this context, a new ecological compressed earth blocks (CEBS) with addition of ground olive stone (GOS) was proposed. The GOS is added as partial clay replacement in different proportions. The main objective of this paper is to study the effect of GOS levels on the thermal properties and mechanical behavior of CEB. We proceeded to determining the optimal water content and equivalent wet density by compaction using a hydraulic press, at a pressure of 10 MPa. The maximum compressive strength is reached at 15% of the GOS. This percentage increases the mechanical properties by 19.66%, and decreases the thermal conductivity by 37.63%. These results are due to the optimal water responsible for the consolidation and compactness of the clay matrix. The substitution up to 30% of GOS shows a decrease of compressive strength and thermal conductivity by about 38.38% and 50.64% respectively. The decrease in dry density and thermal conductivity is related to the content of GOS, which is composed of organic and porous fibers. The GOS seems promising for improving the thermo-mechanical characteristics of CEB and which can also be used as reinforcement in CEBS.

A Study of Some Mechanical and Physical Properties for Palm Fiber/Polyester Composite

2020 ◽  
Vol 38 (3B) ◽  
pp. 104-114
Author(s):  
Samah M. Hussein
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Dielectric Constant ◽  
Date Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Dielectric Strength ◽  
Palm Fiber ◽  
Mechanical And Physical Properties ◽  
Polyester Composite

This research has been done by reinforcing the matrix (unsaturated polyester) resin with natural material (date palm fiber (DPF)). The fibers were exposure to alkali treatment before reinforcement. The samples have been prepared by using hand lay-up technique with fiber volume fraction of (10%, 20% and 30%). After preparation of the mechanical and physical properties have been studied such as, compression, flexural, impact strength, thermal conductivity, Dielectric constant and dielectric strength. The polyester composite reinforced with date palm fiber at volume fraction (10% and 20%) has good mechanical properties rather than pure unsaturated polyester material, while the composite reinforced with 30% Vf present poor mechanical properties. Thermal conductivity results indicated insulator composite behavior. The effect of present fiber polar group induces of decreasing in dielectric strength, and increasing dielectric constant. The reinforcement composite 20% Vf showed the best results in mechanical, thermal and electrical properties.

Study of the boundary layer heat transfer of nanofluids over a stretching sheet: Passive control of nanoparticles at the surface

2015 ◽  
Vol 93 (7) ◽  
pp. 725-733 ◽  
Author(s):  
M. Ghalambaz ◽  
E. Izadpanahi ◽  
A. Noghrehabadi ◽  
A. Chamkha
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Heat Transfer Enhancement ◽  
Base Fluid ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Enhancement Ratio ◽  
Transfer Enhancement

The boundary layer heat and mass transfer of nanofluids over an isothermal stretching sheet is analyzed using a drift-flux model. The relative slip velocity between the nanoparticles and the base fluid is taken into account. The nanoparticles’ volume fractions at the surface of the sheet are considered to be adjusted passively. The thermal conductivity and the dynamic viscosity of the nanofluid are considered as functions of the local volume fraction of the nanoparticles. A non-dimensional parameter, heat transfer enhancement ratio, is introduced, which shows the alteration of the thermal convective coefficient of the nanofluid compared to the base fluid. The governing partial differential equations are reduced into a set of nonlinear ordinary differential equations using appropriate similarity transformations and then solved numerically using the fourth-order Runge–Kutta and Newton–Raphson methods along with the shooting technique. The effects of six non-dimensional parameters, namely, the Prandtl number of the base fluid Prbf, Lewis number Le, Brownian motion parameter Nb, thermophoresis parameter Nt, variable thermal conductivity parameter Nc and the variable viscosity parameter Nv, on the velocity, temperature, and concentration profiles as well as the reduced Nusselt number and the enhancement ratio are investigated. Finally, case studies for Al2O3 and Cu nanoparticles dispersed in water are performed. It is found that increases in the ambient values of the nanoparticles volume fraction cause decreases in both the dimensionless shear stress f″(0) and the reduced Nusselt number Nur. Furthermore, an augmentation of the ambient value of the volume fraction of nanoparticles results in an increase the heat transfer enhancement ratio hnf/hbf. Therefore, using nanoparticles produces heat transfer enhancement from the sheet.

Effect of Coating on the Thermal Conductivities of Diamond/Cu Composites Prepared by Spark Plasma Sintering (SPS)

2014 ◽  
Vol 722 ◽  
pp. 25-29 ◽  
Author(s):  
Q.L. Che ◽  
X.K. Chen ◽  
Y.Q. Ji ◽  
Y.W. Li ◽  
L.X. Wang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Theoretical Prediction ◽  
Volume Fraction ◽  
Interface Reaction ◽  
Copper Matrix ◽  
Bonding Force ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Spark Plasma

The carbide forming is proposed to improve interfacial bonding between diamond particles and copper-matrix for diamond/copper composites. The volume fraction of diamond and minor titanium are optimized. The microstructures, thermal properties, interface reaction production and its effect of minor titanium on the properties of the composites are investigated. The results show that the bonding force and thermal conductivity of the diamond/Cu-Ti alloys composites is much weaker and lower than that of the coated-diamond/Cu. the thermal conductivity of coated-60 vol. % diamond/Cu composites is 618 W/m K which is 80 % of the theoretical prediction value. The high thermal conductivity has been achieved by forming the titanium carbide at diamond/copper interface to gain a good interface.

MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF AMORPHOUS Al–Cu–Ti METAL FOAMS SYNTHESIZED BY SPARK PLASMA SINTERING

2017 ◽  
Vol 24 (Supp02) ◽  
pp. 1850022
Author(s):  
MAOYUAN LI ◽  
LIN LU ◽  
ZHEN DAI ◽  
YIQIANG HONG ◽  
WEIWEI CHEN ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Elevated Temperatures ◽  
Volume Fraction ◽  
Metal Foams ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Xrd Patterns

Amorphous Al–Cu–Ti metal foams were prepared by spark plasma sintering (SPS) process with the diameter of 10[Formula: see text]mm. The SPS process was conducted at the pressure of 200 and 300[Formula: see text]MPa with the temperature of 653–723[Formula: see text]K, respectively. NaCl was used as the space-holder, forming almost separated pores with the porosity of 65 vol%. The microstructure and mechanical behavior of the amorphous Al–Cu–Ti metal foams were systematically investigated. The results show that the crystallinity increased at elevated temperatures. The effect of pressure and holding time on the crystallization was almost negligible. The intermetallic compounds, i.e. Al–Ti, Al–Cu and Al–Cu–Ti were identified from X-ray diffraction (XRD) patterns. It was found that weak adhesion and brittle intermetallic compounds reduced the mechanical properties, while lower volume fraction and smaller size of NaCl powders improved the mechanical properties.

Pool Boiling Characteristics of Metallic Nanofluids

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
K. Hari Krishna ◽  
Harish Ganapathy ◽  
G. Sateesh ◽  
Sarit K. Das
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boiling Heat Transfer ◽  
Volume Fraction ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Solid Particles ◽  
Heater Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Nanofluids, solid-liquid suspensions with solid particles of size of the order of few nanometers, have created interest in many researchers because of their enhancement in thermal conductivity and convective heat transfer characteristics. Many studies have been done on the pool boiling characteristics of nanofluids, most of which have been with nanofluids containing oxide nanoparticles owing to the ease in their preparation. Deterioration in boiling heat transfer was observed in some studies. Metallic nanofluids having metal nanoparticles, which are known for their good heat transfer characteristics in bulk regime, reported drastic enhancement in thermal conductivity. The present paper investigates into the pool boiling characteristics of metallic nanofluids, in particular of Cu-H2O nanofluids, on flat copper heater surface. The results indicate that at comparatively low heat fluxes, there is deterioration in boiling heat transfer with very low particle volume fraction of 0.01%, and it increases with volume fraction and shows enhancement with 0.1%. However, the behavior is the other way around at high heat fluxes. The enhancement at low heat fluxes is due to the fact that the effect of formation of thin sorption layer of nanoparticles on heater surface, which causes deterioration by trapping the nucleation sites, is overshadowed by the increase in microlayer evaporation, which is due to enhancement in thermal conductivity. Same trend has been observed with variation in the surface roughness of the heater as well.

Quantitative Experimental Study of SiO2-Water Nanofluids on Backward-Facing Step Flow under Low Reynolds Number

2018 ◽  
Vol 916 ◽  
pp. 221-225
Author(s):  
Ji Zu Lv ◽  
Liang Yu Li ◽  
Cheng Zhi Hu ◽  
Min Li Bai ◽  
Sheng Nan Chang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Volume Fraction ◽  
Pure Water ◽  
Experimental Studies ◽  
Flow Characteristics ◽  
Thermal Engineering ◽  
Heat Transfer Medium ◽  
Step Flow

Nanofluids is an innovative study of nanotechnology applied to the traditional field of thermal engineering. It refers to the metal or non-metallic nanopowder was dispersed into water, alcohol, oil and other traditional heat transfer medium, to prepared as a new heat transfer medium with high thermal conductivity. The role of nanofluids in strengthening heat transfer has been confirmed by a large number of experimental studies. Its heat transfer mechanism is mainly divided into two aspects. On the one hand, the addition of nanoparticles enhances the thermal conductivity. On the other hand, due to the interaction between the nanoparticles and base fluid causing the changes in the flow characteristics, which is also the main factor affecting the heat transfer of nanofluids. Therefore, a intensive study on the flow characteristics of nanofluids will make the study of heat transfer more meaningful. In this experiment, the flow characteristics of SiO2-water nanofluids in two-dimensional backward step flow are quantitatively studied by PIV. The results show that under the same Reynolds number, the turbulence of nanofluids is larger than that of pure water. With the increase of nanofluids volume fraction, the flow characteristics are constantly changing. The quantitative analysis proved that the nanofluids disturbance was enhanced compared with the base liquid, which resulting in the heat transfer enhancement.

The Estimation of Thermal Conductivity for Alumina-Epoxy Composite Material with High Filling Volume Fraction

2014 ◽  
Vol 918 ◽  
pp. 21-26
Author(s):  
Chen Kang Huang ◽  
Yun Ching Leong
Keyword(s):  
Thermal Conductivity ◽  
Composite Material ◽  
Composite Materials ◽  
Physical Model ◽  
Electron Scattering ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
The Matrix ◽  
Transport Theorem ◽  
Good Agreement

In this study, the transport theorem of phonons and electrons is utilized to create a model to predict the thermal conductivity of composite materials. By observing or assuming the dopant displacement in the matrix, a physical model between dopant and matrix can be built, and the composite material can be divided into several regions. In each region, the phonon or electron scattering caused by boundaries, impurities, or U-processes was taken into account to calculate the thermal conductivity. The model is then used to predict the composite thermal conductivity for several composite materials. It shows a pretty good agreement with previous studies in literatures. Based on the model, some discussions about dopant size and volume fraction are also made.

Sign in / Sign up

Export Citation Format

Share Document