Apatite Formation on Organic-Inorganic Hybrid Containing Sulfonic Group

2005 ◽  
Vol 284-286 ◽  
pp. 725-728 ◽  
Author(s):  
Toshiki Miyazaki ◽  
Moriyoshi Imamura ◽  
Eiichi Ishida ◽  
Masahiro Ashizuka ◽  
Chikara Ohtsuki ◽  
...  
Keyword(s):  
Organic Polymer ◽  
Apatite Formation ◽  
Acrylic Polymer ◽  
Sulfonic Group ◽  
Essential Condition ◽  
Living Body ◽  
Artificial Materials ◽  
Acid Sodium Salt ◽  
Bone Repairing

Apatite formation in living body is essential condition for artificial materials to exhibit bone-bonding ability, i.e. bioactivity. It has been recently revealed that sulfonic group triggers apatite nucleation in body environment. Organic-inorganic hybrids consisting of organic polymer and the sulfonic group are therefore expected to be useful for novel bone-repairing materials exhibiting flexibility as well as bioactivity. In the present study, organic-inorganic hybrids were prepared from vinylsulfonic acid sodium salt and hydroxyethylmethacrylate (HEMA), a kind of acrylic polymer. Bioactivity of the hybrids was assessed in vitro by examining their acceptance of apatite formation in simulated body fluid (SBF, Kokubo solution). The obtained hybrids showed the apatite deposition after soaking in SBF within 7 d.

Apatite-Forming Ability of Organic-Inorganic Hybrids Prepared from Calcium Silicate and Glucomannan

2007 ◽  
Vol 361-363 ◽  
pp. 567-570
Author(s):  
Yasuyuki Morita ◽  
Toshiki Miyazaki ◽  
Eiichi Ishida ◽  
Chikara Ohtsuki
Keyword(s):  
Calcium Silicate ◽  
Body Fluid ◽  
Organic Polymer ◽  
Apatite Formation ◽  
X Ray Diffraction ◽  
Electron Microscopic ◽  
Living Body ◽  
Bioactive Ceramics ◽  
Previously Treated

So-called bioactive ceramics are used for bone-repairing owing to attractive features such as direct bone-bonding in living body. However, there is limitation on clinical applications due to their inappropriate mechanical properties performances such as higher brittleness and lower fracture toughness than natural bone. To overcome this problem, hybrid materials have been developed by modification of calcium silicate, that is basic component of bioactive ceramics, with organic polymer. It is known that bioactive ceramics bond to bone through bone-like apatite layer which is formed on their surfaces by chemical reaction with body fluid. We attempted preparation of bioactive organic-inorganic hybrids from Glucomannan that is a kind of complex polysaccharide, and calcium silicate. Hybrids were prepared from glucomannan and tetraethoxysilane (TEOS). They were treated with 1M (=mol·m-3) CaCl2 aqueous solution for 24 hours. Then ability of apatite formation on the hybrids was examined in vitro using simulated body fluid (SBF, Kokubo solution). Surface structure of the specimens was examined by thin-film X-ray diffraction (TF-XRD), scanning electron microscopic (SEM) observation. The hybrids with TEOS:Glucomannan= 1:1 to 4:1 in mass ratio formed the apatite in SBF within 3 or 7 d, when they were previously treated with CaCl2 solution.

scholarly journals In vitro apatite formation on organic polymers modified with a silane coupling reagent

2005 ◽  
Vol 2 (4) ◽  
pp. 335-340 ◽  
Author(s):  
Yuki Shirosaki ◽  
Masaaki Kubo ◽  
Seisuke Takashima ◽  
Kanji Tsuru ◽  
Satoshi Hayakawa ◽  
...  
Keyword(s):  
High Density Polyethylene ◽  
Body Fluid ◽  
Contact Angles ◽  
Organic Polymer ◽  
Apatite Formation ◽  
Distilled Water ◽  
Organic Polymers ◽  
Coupling Reagent ◽  
Silane Coupling

γ-Methacryloxypropyltrimethoxysilane (γ-MPS) was grafted to high-density polyethylene, polyamide and silicone rubber substrates by the emulsion polymerization procedure in order to provide these organic polymers with in vitro apatite-forming ability. The contact angles towards distilled water of the γ-MPS-grafted specimens were lower than those of the original organic polymer specimens, indicating that the grafted substrates were more hydrophilic. The in vitro apatite formation in a simulated body fluid (Kokubo solution) was confirmed for several of the γ-MPS-grafted specimens.

Effects of Surface Modification of Titania on In Vitro Apatite-Forming Ability

2014 ◽  
Vol 604 ◽  
pp. 196-199 ◽  
Author(s):  
Inga Narkevica ◽  
Jurijs Ozolins ◽  
Liga Berzina-Cimdina
Keyword(s):  
Surface Modification ◽  
Thermal Treatment ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Uv Light ◽  
Biological Response ◽  
Surface Activation ◽  
Living Body ◽  
Artificial Materials

Surface properties of a material play a significant role in manipulating biological response of living body to artificial materials. The aim of this work was put on bioactivity assessment of TiO2 ceramic after thermal treatment and further surface activation with UV-light. The in vitro apatite-forming ability was examined by soaking the samples into the simulated body fluid for several days. The research shows that nanostructural surface and UV irradiation accelerates formation of apatite on TiO2 pellets.

scholarly journals Assessment of Titanate Nanolayers in Terms of Their Physicochemical and Biological Properties

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 806
Author(s):  
Michalina Ehlert ◽  
Aleksandra Radtke ◽  
Katarzyna Roszek ◽  
Tomasz Jędrzejewski ◽  
Piotr Piszczek
Keyword(s):  
Surface Modification ◽  
Substrate Surface ◽  
Biological Properties ◽  
Structure Characterization ◽  
Porous Coating ◽  
Apatite Formation ◽  
Sem Images ◽  
Energy Dispersion Spectroscopy ◽  
X Ray

The surface modification of titanium substrates and its alloys in order to improve their osseointegration properties is one of widely studied issues related to the design and production of modern orthopedic and dental implants. In this paper, we discuss the results concerning Ti6Al4V substrate surface modification by (a) alkaline treatment with a 7 M NaOH solution, and (b) production of a porous coating (anodic oxidation with the use of potential U = 5 V) and then treating its surface in the abovementioned alkaline solution. We compared the apatite-forming ability of unmodified and surface-modified titanium alloy in simulated body fluid (SBF) for 1–4 weeks. Analysis of the X-ray diffraction patterns of synthesized coatings allowed their structure characterization before and after immersing in SBF. The obtained nanolayers were studied using Raman spectroscopy, diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), and scanning electron microscopy (SEM) images. Elemental analysis was carried out using X-ray energy dispersion spectroscopy (SEM EDX). Wettability and biointegration activity (on the basis of the degree of integration of MG-63 osteoblast-like cells, L929 fibroblasts, and adipose-derived mesenchymal stem cells cultured in vitro on the sample surface) were also evaluated. The obtained results proved that the surfaces of Ti6Al4V and Ti6Al4V covered by TiO2 nanoporous coatings, which were modified by titanate layers, promote apatite formation in the environment of body fluids and possess optimal biointegration properties for fibroblasts and osteoblasts.

Tailoring the in vitro characteristics of poly(vinyl alcohol)-nanohydroxyapatite composite scaffolds for bone tissue engineering

2016 ◽  
Vol 36 (8) ◽  
pp. 771-784 ◽  
Author(s):  
Tejinder Kaur ◽  
Arunachalam Thirugnanam ◽  
Krishna Pramanik
Keyword(s):  
Mechanical Strength ◽  
Vinyl Alcohol ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Poly Vinyl Alcohol ◽  
Apatite Formation ◽  
Composite Scaffolds ◽  
Alizarin Red ◽  
Casting Technique

Abstract Poly(vinyl alcohol) reinforced with nanohydroxyapatite (PVA-nHA) composite scaffolds were developed by varying the nHA (1%, 2%, 3%, 4%, and 5%, w/v) composition in the PVA matrix by solvent casting technique. The developed composite scaffolds were characterized using scanning electron microscopy (SEM), X-ray powder diffraction (XRD), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, and contact angle measurement. The stability of the composite scaffolds in physiological environment was evaluated by swelling and degradation studies. Further, these composite scaffolds were tested for in vitro bioactivity, hemolysis, biocompatibility, and mechanical strength. SEM micrographs showed a homogenous distribution of nHA (3%, w/v) in the PVA matrix. XRD and ATR-FTIR analysis confirmed no phase contamination and the existence of the chemical bond between PVA-nHA at approximately 2474 cm-1. PVA-nHA composite scaffolds with 3% (w/v) concentration of nHA showed nominal swelling and degradation behavior with good mechanical strength. The mechanical strength and degradation properties of the scaffold above 3% (w/v) of nHA was found to deteriorate, which is due to the agglomeration of nHA. The in vitro bioactivity and hemolysis studies showed improved apatite formation and hemocompatibility of the developed scaffolds. In vitro cell adhesion, proliferation, alkaline phosphatase activity, and Alizarin red S staining confirmed the biocompatibility of the composite scaffolds.

Study of Bio-Mineralization of BCP with Compensation of Calcium and Phosphate Ions

2009 ◽  
Vol 610-613 ◽  
pp. 1391-1394
Author(s):  
Hua De Zheng ◽  
Ying Jun Wang ◽  
Qiang Ma ◽  
Cheng Yun Ning ◽  
Xiao Feng Chen
Keyword(s):  
Free Energy ◽  
Calcium Phosphate ◽  
Calcium Ions ◽  
Biphasic Calcium Phosphate ◽  
Porous Ceramic ◽  
Apatite Layer ◽  
Apatite Formation ◽  
Phosphate Ions

In the present study, an Intelligent Multi-parameter Simulated Evaluation in vitro （IMSE system） was used to study the deposition properties of apatite formation on the surface of biphasic calcium phosphate porous ceramic (BCP) from static and dynamic r-SBF. Results showed that apatite formed on the surface of BCP from static and dynamic r-SBF differed between each other. In static r-SBF, ions were transferred by diffusion, which could not compensate the consuming of calcium ions, and mist apatite layer was formed on the surface of samples. But in the dynamic r-SBF, simulated fluid was adjusted precisely and flowed forcedly, the concentrations of ions were homogeneous; with the compensation of ions, calcium and phosphate were supersaturated, and the free energy of apatite formation was negative, bone-like apatite sheets were formed on the surface of samples.

Physicochemical Characterization and In-Vitro Antimicrobial Activity of Chitosan Extracted from Shrimp Shells Waste from Beni Saf Sea, Algeria

2018 ◽  
Vol 7 (3) ◽  
pp. 122-129
Author(s):  
Fatma Youcefi ◽  
Ali Riazi ◽  
Meriem Mokhtar ◽  
Tefiani Choukri ◽  
Khaouani Naima
Keyword(s):  
Antimicrobial Activity ◽  
Physicochemical Characterization ◽  
Organic Polymer ◽  
In Vitro Antimicrobial Activity ◽  
Physiochemical Parameters ◽  
Microdilution Method ◽  
Molecular Arrangement ◽  
Shrimp Shells ◽  
Broth Microdilution Method

Chitosan is the most abundant natural organic polymer in nature. Its positive charge and its molecular arrangement confer interesting properties on the plane food, pharmaceutical, medical, cosmetic, water treatment. The present study was undertaken to study the physiochemical parameters and the in vitro antimicrobial activity of chitosan extracted from shrimp shells waste. The molecular weight of chitosan is 1414.33±16.99 kDa with, the percent of Ash 0,345±0,040 %, moisture is 2,98 ±0,13 % , and protein is 0.3 ±0,041 %.Chitosan produced (5 %) was also characterized with Fourier Transform Infrared Spectroscopy (FTIR) the spectrum of the chitosan sample from the shell recorded 16 peaks in the range of 689.40/cm and 3430.02 /cm. The antibacterial and antifungul activities of chitosan were examined against Escherichia coli ATCC10536, Pseudomonas aeruginosa ATCC 27853, Listeria monocytogenes ATCC7644, Staphylococcus aureus ATCC29213, Aspergillus niger ATCC 16888 and Candida albicans ATCC 10231 by agar wells diffusion the tests inhibitions zones diameters were 49,74± 0,75 , 54,35±0,93 , 42,27±1,07 , 32,95±0,28 and 53,73±0,64mm respectively. The minimum inhibitory concentration (MIC) using a broth microdilution method against tested microorganisms was ranging from 008% to 1.22%. These results open interesting perspectives of the chitosan. It can be used as new biomaterial with utility in many industrial areas.

In vitro degradability and apatite-formation ability of monticellite (CaMgSiO4) bioceramic

2019 ◽  
Vol 45 (3) ◽  
pp. 3754-3759 ◽  
Author(s):  
J. Ma ◽  
B.X. Huang ◽  
X.C. Zhao ◽  
C.L. Ban ◽  
X.H. Hao ◽  
...  
Keyword(s):  
Apatite Formation

Preparation and In Vitro Characterization of Polycaprolactone and Demineralized Bone Matrix Scaffolds

2012 ◽  
Vol 1417 ◽  
Author(s):  
Titilayo Moloye ◽  
Christopher Batich
Keyword(s):  
Demineralized Bone Matrix ◽  
Bone Matrix ◽  
Apatite Formation ◽  
Alizarin Red ◽  
Salt Leaching ◽  
Synthetic Materials ◽  
Calcium And Phosphorus ◽  
Demineralized Bone

ABSTRACTCylindrical porous polycaprolactone (PCL) scaffolds containing 25, 35, and 50 wt% demineralized bone matrix (DBM) were fabricated using a salt-leaching method for application in bone engineering. In the present work, PCL-DBM scaffolds were monitored for calcium and phosphorus deposition in both deionized (DI) water and simulated body fluid (SBF) for time periods of 5, 10, 15, and 20 days at 37°C under constant rotation. An in vitro assessment of the bioactivity of synthetic materials using SBF under physiological conditions can be used as a barometer of scaffold behavior in vivo. DBM, an osteoinductive material, was used to gauge if there was a correlation between the concentration of DBM within a scaffold and the apatite formation on its surface. Biochemical assays, alizarin red S staining, and scanning electron microscopy (SEM) with elemental analysis of calcium and phosphorus were consistent in that they confirmed that PCL scaffolds containing 35 wt% DBM in SBF at 14 days post-immersion showed signs of early apatite formation.

scholarly journals In vitro Release Kinetics Study of Ambroxol Hydrochloride Pellets Developed by Extrusion Spheronization Technique Followed by Acrylic Polymer Coating

1970 ◽  
Vol 7 (1) ◽  
pp. 75-81 ◽  
Author(s):  
Ishtiaq Ahmed ◽  
Monzurul Amin Roni ◽  
Golam Kibria ◽  
Muhammad Rashedul Islam ◽  
Reza-ul Jalil
Keyword(s):  
Drug Release ◽  
Release Kinetics ◽  
In Vitro Dissolution ◽  
Acrylic Polymer ◽  
Eudragit Rs ◽  
Methacrylate Copolymer ◽  
Ambroxol Hydrochloride ◽  
Eudragit Rl ◽  
Extrusion Spheronization

The aim of the present study was to investigate the effect of Ammonio Methacrylate Copolymer Dispersion Type A (Eudragit RL 30 D) and Ammonio Methacrylate Copolymer Dispersion Type B (Eudragit RS 30 D) combination in different weight ratios on the release kinetics of Ambroxol Hydrochloride from coated pellets. Microcrystalline cellulose, lactose, maize starch, hydroxypropyl methylcellulose and the drug was incorporated in the nuclei prepared by Extrusion-Spheronization technique which was coated with Eudragit RL 30D and Eudragit RS 30D in 1:1,1:1.5,1:2,1:2.5 and 1:3 ratios. The in vitro dissolution studies were carried out in 0.1N HCl for 1 hour followed by phosphate buffer (pH 6.8) for 11 h with USP dissolution apparatus Type-II. Drug release decreased with increasing amount of Eudragit RS 30 D in all cases. The drug release followed first order and Higuchi release kinetics. The Korsmeyer plot revealed n=0.50-0.61 or non-Fickian transport mechanism for drug release. From one way ANOVA it was found that the ratio of binary polymer mixer had significant (p < 0.05) effect on drug release. Key words: Aqueous coating, Eudragit, release kinetics, pellet, extrusion-spheronization  DOI = 10.3329/dujps.v7i1.1222 Dhaka Univ. J. Pharm. Sci. 7(1): 75-81, 2008 (June)

Sign in / Sign up

Export Citation Format

Share Document