Effect of Additives on Hydrolysis of Ti Alkoxide and Microstructural Observation of TiO2

2006 ◽  
Vol 317-318 ◽  
pp. 89-92 ◽  
Author(s):  
Atsushi Nakahira ◽  
Y. Fujita ◽  
T. Kubo ◽  
S. Eguchi ◽  
S. Nishida ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Average Particle Size ◽  
Average Particle ◽  
Tio2 Powder ◽  
Microstructural Observation ◽  
Effect Of Additives ◽  
Xrd Patterns ◽  
Hydrolysis Of ◽  
Fine Tio2

By the usage of the hydrolysis of Ti alkoxide, various types of TiO2 were obtained through the addition of catalyst (HCl, NH4OH, and CH3COONH4) and some additives into Ti alkoxide solution at room temperature. In special, the effect of two additives, diethylene glycol (DEG) and hexamethylphospheric triamide (HMPA), on hydrolysis behaviors and microstructure with various catalyst for hydrolysis of Ti-tetraisopropoxide was in detail investigated. In case of TiO2 powder with HMPA as an additive, the crystallinity of TiO2 except with NH4OH as a catalyst decreased in XRD patterns, compared to those of products with no additive and with DEG as an additive. The addition of HMPA prohibited the growth of TiO2 and led to fine TiO2 with the average particle size of approximately 10nm.

Minimum Particle Diameter of the Vanadium/Iron Co-Doped Nano TiO2 Transparent Hydrosol at Room Temperature

2014 ◽  
Vol 989-994 ◽  
pp. 611-614
Author(s):  
Ling Li ◽  
Wen Ming Zhang ◽  
Hua Yan Zhang ◽  
Zi Hao Xu ◽  
Sen Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Raw Materials ◽  
Average Particle Size ◽  
Particle Diameter ◽  
Ferric Nitrate ◽  
Average Particle ◽  
Hydrolysis Method ◽  
Vanadium Iron ◽  
Co Doped

Vanadium/iron co-doped nanoTiO2 transparent hydrosol with an average particle size of 3.8 nm was synthesized by a novel complexation-controlled hydrolysis method at room temperature and atmospheric pressure by using TiCl4, ferric nitrate, ammonium metavanadate, etc. as raw materials. The composition, phase structure, particle size, absorbance spectrum, and photocatalytic performance of samples were characterized by XRD, EDS, nanolaser particle size analyzer, and UV-Vis spectrophotometer. The photocatalytic properties of V/Fe doped TiO2 were studied through degrading acid 3R dye, and the results show that when the content of V/Fe was 0.5%, the degradation rate reached more than 96% under irridation for 60 min.

Fabrication and Characterization of Nanospinel ZnCr2O4 Using Thermal Treatement Method

2015 ◽  
Vol 1107 ◽  
pp. 301-307 ◽  
Author(s):  
Salahudeen A. Gene ◽  
Elias B. Saion ◽  
Abdul Halim Shaari ◽  
Mazliana A. Kamarudeen ◽  
Naif Mohammed Al-Hada
Keyword(s):  
Particle Size ◽  
Calcination Temperature ◽  
Average Particle Size ◽  
Treatment Method ◽  
Esr Spectra ◽  
Resonance Spectroscopy ◽  
Average Particle ◽  
Face Centered Cubic ◽  
X Ray ◽  
Xrd Patterns

The fabrication of nanospinel zinc chromite (ZnCr2O4) crystals by the means of thermal treatment method from an aqueous solution containing metal nitrates, polyvinyl pyrrolidone (PVP), and deionized water was described in this study. The samples were calcined at various temperatures ranging from 773 to 973 K for the decomposition of the organic compounds and crystallization of the nanocrystals. PVP was used as capping agent to control the agglomeration of the particles. The characterization studies of the fabricated samples were carried out by X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM), energy dispersed X-ray spectroscopy (EDX) and electron spin resonance spectroscopy (ESR). The corresponding peaks of Zn, Cr and O were observed in the EDX spectrum of the sample which confirms the formation of ZnCr2O4. The XRD patterns also confirmed the formation of the single faced nanocrystallines of spinel ZnCr2O4 with a face-centered cubic structure. The average particle size of the synthesized crystals was also determined from the XRD patterns using the Scherers formula which shows that the crystallite sizes increases with increase in calcination temperature and was in good agreement with the TEM images which shows cubical ZnCr2O4 nanocrystals with uniform morphology and particle size distributions. The ESR spectra confirmed the existence of unpaired electron in the fabricated samples and the increase in g-factor and decreases in resonant magnetic field (Hr) were observed as the calcination temperature increases.

Frequency dependence and fuel effect on optical properties of nano TiO2-based structures

2016 ◽  
Vol 30 (18) ◽  
pp. 1650247 ◽  
Author(s):  
Mahdi Ghasemifard ◽  
Misagh Ghamari ◽  
Meysam Iziy
Keyword(s):  
Particle Size ◽  
Optical Properties ◽  
Average Particle Size ◽  
Combustion Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
Transmission Electron ◽  
Auto Combustion ◽  
Xrd Patterns

TiO2-(Ti[Formula: see text]Si[Formula: see text]O2 nanopowders (TS-NPs) with average particle size around 90 nm were successfully synthesized by controlled auto-combustion method by using citric acid/nitric acid (AC:NA) and urea/metal cation (U:MC). The structure of powders was studied based on their X-ray diffraction (XRD) patterns. The XRD of TS-NPs shows that rutile and anatase are the main phases of TS-NPs for AC:NA and U:MC, respectively. Particle size and histogram of nanopowders were characterized by transmission electron microscopy (TEM) and dynamic light scattering (DLS). Optical properties of TS-NPs were calculated by Fourier transform infrared spectroscopy (FTIR) and Kramers–Kroning (KK) relation. Plasma frequencies of TS-NPs obtained from energy loss functions depend on fuels as a result of changes in crystal structure, particle size distribution, and morphology.

scholarly journals Monodispersed ZnO Nanoparticles and Their Use in Heterojunction Solar Cell

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Dinesh Patidar ◽  
Anusaiya Kaswan ◽  
N. S. Saxena ◽  
Kananbala Sharma
Keyword(s):  
Particle Size ◽  
Solar Cell ◽  
Ethylene Glycol ◽  
Zno Nanoparticles ◽  
Ultrasonic Treatment ◽  
Room Temperature ◽  
Power Conversion ◽  
Average Particle Size ◽  
Hexagonal Wurtzite Structure ◽  
Average Particle

Monodispersed ZnO nanoparticles have been synthesised in ethylene glycol medium using zinc acetate and sodium hydroxide at room temperature through ultrasonic treatment. The monodispersed ZnO nanoparticles were characterized by XRD, TEM, SEM, and optical spectroscopy. The results indicate that ZnO shows the hexagonal wurtzite structure having 8 nm average particle size with the band gap of 3.93 eV. ZnO nanoparticles blended with P3HT show the improvement in the interchains and intrachains ordering as compared to pure P3HT. The power conversion efficiency of P3HT/ZnO solar cell is found to be 0.88%, which is comparable with the result obtained by other researchers.

Development of Heterostructured Ferroelectric SrZrO3/CdS Photocatalysts with Enhanced Surface Area and Photocatalytic Activity

2020 ◽  
Vol 20 (6) ◽  
pp. 3770-3779 ◽  
Author(s):  
Umar Farooq ◽  
Farheen Naz ◽  
Ruby Phul ◽  
Nayeem Ahmad Pandit ◽  
Sapan Kumar Jain ◽  
...  
Keyword(s):  
Particle Size ◽  
Dielectric Constant ◽  
Photocatalytic Activity ◽  
Surface Area ◽  
Room Temperature ◽  
Average Particle Size ◽  
Chemical Deposition ◽  
Bet Surface Area ◽  
Cds Nanoparticles ◽  
Average Particle

This paper reports the attempt to develop an efficient heterostructure photocatalyst by employing SrZrO3 as ferroelectric substrate with deposited nanostructured CdS semiconductor on the surface. Primarily bare SrZrO3 and CdS nanoparticles were synthesized by using polymeric citrate precursor and co-precipitation routes, respectively. The chemical deposition technique was used to develop the CdS over the surface of the pre-synthesized SrZrO3 nanoparticles. The synthesized bare nanoparticles and their heterostructure were characterized by XRD which shows the formation of orthorhombic and face centred cubic (FCC) phases of SrZrO3 and CdS, respectively. TEM was used to estimate the morphology and particle size of as-synthesized nanoparticles, which shows the average particle size of 14, 24 and 25 nm for SrZrO3, CdS and SrZrO3/CdS, respectively. The BET surface area of SrZrO3, CdS and SrZrO3/CdS samples was found to be 299, 304 and 312 m2/g respectively. Methylene blue was used as model pollutant to determine the photocatalytic activity of the synthesized nanomaterials. The heterostructure shows an enhanced activity as compared to bare nanoparticles. Dielectric constant and dielectric loss of the nanoparticles was investigated as a function of frequency at room temperature and as a function of temperature at 500 kHz. The room temperature dielectric constant for SrZrO3, CdS and SrZrO3/CdS was found to be 13.2, 17.8 and 25.5 respectively at 100 kHz.

scholarly journals Improving the CO and CH4 Gas Sensor Response at Room Temperature of α-Fe2O3(0001) Epitaxial Thin Films Grown on SrTiO3(111) Incorporating Au(111) Islands

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 848
Author(s):  
Aída Serrano ◽  
Jesús López-Sánchez ◽  
Iciar Arnay ◽  
Rosalía Cid ◽  
María Vila ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Gas Sensing ◽  
Structural Characteristics ◽  
Average Particle Size ◽  
Average Particle ◽  
Epitaxial Thin Films ◽  
Before And After ◽  
Crystallographic Axes ◽  
Gas Exposure

In this work, the functional character of complex α-Fe2O3(0001)/SrTiO3(111) and Au(111) islands/α-Fe2O3(0001)/SrTiO3(111) heterostructures has been proven as gas sensors at room temperature. Epitaxial Au islands and α-Fe2O3 thin film are grown by pulsed laser deposition on SrTiO3(111) substrates. Intrinsic parameters such as the composition, particle size and epitaxial character are investigated for their influence on the gas sensing response. Both Au and α-Fe2O3 layer show an island-type growth with an average particle size of 40 and 62 nm, respectively. The epitaxial and incommensurate growth is evidenced, confirming a rotation of 30° between the in-plane crystallographic axes of α-Fe2O3(0001) structure and those of SrTiO3(111) substrate and between the in-plane crystallographic axes of Au(111) and those of α-Fe2O3(0001) structure. α-Fe2O3 is the only phase of iron oxide identified before and after its functionalization with Au nanoparticles. In addition, its structural characteristics are also preserved after Au deposition, with minor changes at short-range order. Conductance measurements of Au(111)/α-Fe2O3(0001)/SrTiO3(111) system show that the incorporation of epitaxial Au islands on top of the α-Fe2O3(0001) layer induces an enhancement of the gas-sensing activity of around 25% under CO and 35% under CH4 gas exposure, in comparison to a bare α-Fe2O3(0001) layer grown on SrTiO3(111) substrates. In addition, the response of the heterostructures to CO gas exposure is around 5–10% higher than to CH4 gas in each case.

scholarly journals β-hexanitrohexaazaisowurtzitane Particles Prepared by Spray Drying and its Characterization

2021 ◽  
Vol 27 (1) ◽  
pp. 119-124
Author(s):  
Wenzheng XU ◽  
Hao LI ◽  
Xin LIANG ◽  
Jie WANG ◽  
Jinyu PENG ◽  
...  
Keyword(s):  
Particle Size ◽  
Spray Drying ◽  
Ultrafine Particles ◽  
Average Particle Size ◽  
Narrow Particle Size Distribution ◽  
Average Particle ◽  
Thermal Stimulus ◽  
Particle Size Analyzer ◽  
Xrd Patterns ◽  
The Impact

In this paper, the ultrafine β-hexanitrohexaazaisowurtzitane (β – CL – 20) particles were prepared by spray drying method. The CL – 20 samples were characterized by scanning electron microscope (SEM), particle size analyzer, X-ray diffraction (XRD), and Differential Scanning Calorimeter (DSC). Furthermore, the safety properties of samples under impact and thermal stimulus were tested and analyzed. The results of SEM showed that the average particle size of ultrafine CL – 20 particles with a narrow particle size distribution, were about 320 nm, and the shape was elliptical. The XRD patterns indicated that the polymorphic phase of ultrafine particles was mainly β-type. Compared with that of raw CL – 20, the impact sensitivity of the ultrafine CL – 20 had been decreased significantly, for the drop height (H50) was increased from 13.0 to 33.5 cm. The critical explosion temperature of the ultrafine CL – 20 decreased from 232.16 ℃ to 227.93 ℃, indicating that the thermal stability of the ultrafine CL – 20 is lower than that of raw CL – 20.

Minimum Particle Diameter of the Sulfur-Doped Nano-TiO2 Transparent Hydrosol at Room Temperature

2014 ◽  
Vol 587-589 ◽  
pp. 788-791
Author(s):  
Ling Li ◽  
Hua Yan Zhang ◽  
Xiao Wei Li ◽  
Zi Hao Xu ◽  
Sen Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Photocatalytic Performance ◽  
Raw Materials ◽  
Average Particle Size ◽  
Particle Diameter ◽  
Synthesis Process ◽  
Average Particle ◽  
Hydrolysis Method ◽  
Particle Size Analyzer

Sulfur-doped nanoTiO2transparent hydrosol with an average particle size of 3.8 nm was synthesized by a novel complexation-controlled hydrolysis method at room temperature and atmospheric pressure by using TiCl4, thiourea, organic carboxylic acid, NH3H2O, D-sorbitol etc. as raw materials. The composition, phase structure, particle size, absorbance spectrum, and photocatalytic performance of samples were characterized by XRD, nanolaser particle size analyzer, ultraviolet-visible spectrophotometer. In addition, the influence of reaction conditions in the synthesis process was also studied. The results indicate that when nanoparticle doped with 0.5% S, and the reflux time was 15 min, the photocatalytic performance of sulfur-doped TiO2hydrosol was best.

Ultrafine TiO2 Powders Prepared from Aqueous TiCl4 Solutions at Room Temperature

2007 ◽  
Vol 353-358 ◽  
pp. 2135-2138
Author(s):  
Hong Liang Yi ◽  
Jie Zhang ◽  
Ming Tu Ma ◽  
Hao Zhang ◽  
Bong Ho Lee ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Ph Value ◽  
Anatase Phase ◽  
Average Particle Size ◽  
Rutile Phase ◽  
Average Particle ◽  
Spectral Peaks ◽  
Scherrer Formula ◽  
Stock Solutions

Ultrafine TiO2 powders as rutile and anatase phase were simply precipitated at room temperature for only tens of hours by simply controlling the pH value and Ti4+ concentration via aqueous TiCl4 solution. Under the optimal pH value and Ti4+ concentration, the average particle size of powders with rutile phase was 3.7nm, while that of powders with anatase phase was 3.0nm. The average particle size was calculated from the broadening of corresponding X-ray spectral peaks by Scherrer formula. In addition, 3.0 mol.l-1 are suggested to be used as concentration of stock solutions instead of the current concentration 2.0 mol.l-1.

scholarly journals Preparation and Evaluation of Sunflower Oil Nanoemulsion As a Sunscreen

2019 ◽  
Vol 7 (22) ◽  
pp. 3757-3761
Author(s):  
Anayanti Arianto ◽  
Cindy Cindy
Keyword(s):  
Particle Size ◽  
High Temperature ◽  
Low Temperature ◽  
Sunflower Oil ◽  
Room Temperature ◽  
Ph Value ◽  
Average Particle Size ◽  
Tween 80 ◽  
Average Particle ◽  
Spontaneous Emulsification

BACKGROUND: There are a lot of different types of sunscreen products (oils, sticks, gels, creams, lotions) which can be found on the world's market. Sunscreen product that contains active chemical ingredients sometimes has harmful effects on the skin. Sunflower oil contains vitamin E and acts as a natural sunscreen which can absorb UVB light. The average droplet size of nanoemulsion is between 100 and 500 nm and do not show the problems of stability (creaming, flocculation, coalescence, and sedimentation), which are commonly associated with macroemulsions. AIM: The aim of this study was to prepare and evaluate the sunflower oil nanoemulsion as a sunscreen. METHODS: Sunflower oil nanoemulsions were prepared by spontaneous emulsification method with 3 formulas F1 (Tween 80 38%, sorbitol 22%), F2 (Tween 80 36%, sorbitol 24%), F3 (Tween 80 34%, sorbitol 26%) and 5% sunflower oil as a sunscreen substance. The nanoemulsions were evaluated for particle size, physical stability in room temperature (25 ± 2°C), low temperature (4 ± 2°C) and high temperature (40 ± 2°C) during experiment for 12 weeks of storage, centrifugation at 3750 rpm for 5 hours, viscosity, pH, freeze-thaw test and sun protection value (SPF) value by in vitro. RESULTS: The results of nanoemulsion evaluation showed that nanoemulsion formula F1 had the smallest average particle size of 124.47 nm with yellowish colour, clear, transparent, pH value (6.5 ± 0.1), viscosity value (225 ± 25 cP), did not show any separation or creaming in the centrifugation, and stable during experiment for 12 weeks of storage at room temperature, low temperature and high temperature. The SPF value of all nanoemulsion preparations was higher than that of the emulsion. CONCLUSION: The preparation of the sunflower oil nanoemulsion with a ratio of Tween 80 and sorbitol (38: 22) produces a stable nanoemulsion during the experiment for 12 weeks storage at the room, low and high temperature. The nanoemulsion preparation has higher SPF values compared to the emulsion. This nanoemulsion formulation could be considered more effective in sunscreen cosmetic use compare to the emulsion.

Sign in / Sign up

Export Citation Format

Share Document