Novel Low-Cost Activated Carbon from Coconut Shell and its Adsorptive Characteristics for Carbon Dioxide

2013 ◽  
Vol 594-595 ◽  
pp. 240-244
Author(s):  
Nor Adilla Rashidi ◽  
Suzana Yusup ◽  
Azry Borhan
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Gas Adsorption ◽  
Low Cost ◽  
Operating Cost ◽  
Combustion Process ◽  
Coconut Shell ◽  
Physical Activation ◽  
Activation Process

The objective of this research is to synthesize the microporous activated carbon and test its applicability for CO2gas capture. In this study, coconut shell-based and commercial activated carbon is used as the solid adsorbent. Based on the findings, it shows that the gas adsorption capacity is correlated to the total surface area of the materials. In addition, reduction in the adsorption capacity with respect to temperature proves that the physisorption process is dominant. Higher carbon dioxide (CO2) adsorption capacity in comparison to nitrogen (N2) capacity contributes to higher CO2/N2selectivity, and confirms its applicability in the post-combustion process. Utilization of abundance agricultural wastes and one-step physical activation process is attractive as it promotes a cleaner pathway for activated carbon production, and simultaneously, reduces the total operating cost.

scholarly journals CO2 and CH4 Adsorption Behavior of Biomass-Based Activated Carbons

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3136 ◽  
Author(s):  
Deneb Peredo-Mancilla ◽  
Imen Ghouma ◽  
Cecile Hort ◽  
Camelia Matei Ghimbeu ◽  
Mejdi Jeguirim ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Gas Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Micropore Volume ◽  
Activation Method ◽  
Physical Activation

The aim of the present work is to study the effect of different activation methods for the production of a biomass-based activated carbon on the CO 2 and CH 4 adsorption. The influence of the activation method on the adsorption uptake was studied using three activated carbons obtained by different activation methods (H 3 PO 4 chemical activation and H 2 O and CO 2 physical activation) of olive stones. Methane and carbon dioxide pure gas adsorption experiments were carried out at two working temperatures (303.15 and 323.15 K). The influence of the activation method on the adsorption uptake was studied in terms of both textural properties and surface chemistry. For the three adsorbents, the CO 2 adsorption was more important than that of CH 4 . The chemically-activated carbon presented a higher specific surface area and micropore volume, which led to a higher adsorption capacity of both CO 2 and CH 4 . For methane adsorption, the presence of mesopores facilitated the diffusion of the gas molecules into the micropores. In the case of carbon dioxide adsorption, the presence of more oxygen groups on the water vapor-activated carbon enhanced its adsorption capacity.

scholarly journals Synthesis and Characterisation of Pyridinium-Based Ionic Liquid as Activating Agent in Rubber Seed Shell Activated Carbon Production for CO2 Capture

2021 ◽  
Vol 82 (1) ◽  
pp. 85-95
Author(s):  
Nawwarah Mokti ◽  
Azry Borhan ◽  
Siti Nur Azella Zaine ◽  
Hayyiratul Fatimah Mohd Zaid
Keyword(s):  
Ionic Liquid ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Co2 Capture ◽  
Low Cost ◽  
Chemical Activation ◽  
Green Technology ◽  
Activation Process ◽  
Rubber Seed ◽  
Activating Agent

The use of an activating agent in chemical activation of activated carbon (AC) production is very important as it will help to open the pore structure of AC as adsorbents and could enhance its performance for adsorption capacity. In this study, a pyridinium-based ionic liquid (IL), 1-butylpyridinium bis(trifluoromethylsulfonyl) imide, [C4Py][Tf2N] has been synthesized by using anion exchange reaction and was characterized using few analyses such as 1H-NMR, 13C-NMR and FTIR. Low-cost AC was synthesized by chemical activation process in which rubber seed shell (RSS) and ionic liquid [C4Py][Tf2N] were employed as the precursor and activating agent, respectively. AC has been prepared with different IL concentration (1% and 10%) at 500°C and 800°C for 2 hours. Sample AC2 shows the highest SBET and VT which are 392.8927 m2/g and 0.2059 cm3/g respectively. The surface morphology of synthesized AC can be clearly seen through FESEM analysis. A high concentration of IL in sample AC10 contributed to blockage of pores by the IL. On the other hand, the performance of synthesized AC for CO2 adsorption capacity also studied by using static volumetric technique at 1 bar and 25°C. Sample AC2 contributed the highest CO2 uptakes which is 50.783 cm3/g. This current work shows that the use of low concentration IL as an activating agent has the potential to produce porous AC, which offers low-cost, green technology as well as promising application towards CO2 capture.

scholarly journals EFFECT OF THE CARBONIZATION AND ACTIVATION PROCESS ON THE ADSORPTION CAPACITY OF RICE HUSK ACTIVATED CARBON

2017 ◽  
Vol 55 (4) ◽  
pp. 494 ◽  
Author(s):  
Hoa Thai Ma ◽  
Hung Cam Ly ◽  
Van Thi Thanh Ho ◽  
Nguyen Bao Pham ◽  
Dat Chi Nguyen ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Rice Husk ◽  
Raw Materials ◽  
Internal Surface ◽  
Surface Characteristics ◽  
Bet Surface Area ◽  
Adsorptive Capacity ◽  
Physical Activation ◽  
Activation Process

In this study, rice husk was used as a precursor to prepare activated carbon using steam as a physical activation agent. Steam for activation can be used to activate almost all raw materials. A variety of methods have been developed but all of these share the same basic principle of initial carbonization followed by an activation step with steam. The study also investigates the effects of preparation parameters on the surface characteristics of the carbon. These parameters include the range of temperature and time in the carbonization and activation. The initial carbonization, done at temperatures up to 500°C in 60 min, is a highly exothermic process where the temperature is strictly controlled. The creation of the internal surface is done during the activation step with steam at temperatures 800°C in 30 min., for which the BET surface area is up to 710.8m2/g. Besides, the iodine and methylene blue adsorption capacity of rice-husk carbon are the best that reach 865.98±6.5 and 217.86±1.0 (mg/g), respectively. The entire synthetic procedure was simple, environmental-friendly and economical-effectively. The application prospect of the activated carbon prepared in this work was much more promising due to its high adsorptive capacity.

Extraordinary Adsorption Properties of Nano Porous Hydrophobic Silica Aerogels

2012 ◽  
Vol 512-515 ◽  
pp. 45-48 ◽  
Author(s):  
Xiao Qing Wei ◽  
Xing Yuan Ni ◽  
Zhi Hua Zhang ◽  
Jun Shen ◽  
Ai Du ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Gas Adsorption ◽  
Low Cost ◽  
Silica Aerogels ◽  
Angle Measurement ◽  
Adsorption Properties ◽  
Activated Carbon Fiber ◽  
Poly Vinyl Alcohol ◽  
Hydrophobic Silica

The adsorption properties of hydrophobic silica aerogels were studied. Polyethoxy- disiloxanes (E-40), ethanol (EtOH), hydrogen fluoride (HF) were used as silican precursor, solvent and catalyst, respectively, followed by solvent substitution and surface modification to prepare silica aerogels. Scanning electronic microscopy, nitrogen adsorption analyzer, contact angle measurement and Fourier transform infrared spectroscopy were used to characterize the structure and properties of silica aerogels. The conclusion is that the silica aerogels are with good hydrophobicity and the gas adsorption capacities is excellent for toxic gases such as benzene and carbon tetrachloride, which is 2~3 times higher than that of activated carbon fiber (ACF) or granule of activated carbon (GAC). Moreover, the adsorption capacity for organic solvent is 20-30 times of its own weight, which is much larger than that of GAC or Poly vinyl alcohol (PVA). In addition, the adsorption capacity of silica aerogels remains almost the same value after two times of adsorption- desorption processes, which means that the process is recyclable, low-cost and environmental friendly.

ADVANCEMENT IN THE PRODUCTION OF ACTIVATED CARBON FROM BIOMASS USING MICROWAVE HEATING

2017 ◽  
Vol 79 (3) ◽  
Author(s):  
Adekunle Moshood Abioye ◽  
Farid Nasir Ani
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Microwave Heating ◽  
Process Parameters ◽  
Flow Rate ◽  
Microwave Power ◽  
Physical Activation ◽  
Activation Process ◽  
Agent Flow ◽  
Radiation Time

An overview of recent advancement in the production of activated carbon (AC) from biomass using microwave heating is presented. The use of microwave heating method for the thermal conversion of biomass to useful products has been on the increase in the last decade because it offers fast and uniform heating, and a higher level of automation. The effects of process parameters (microwave power and radiation time, agent flow rate in physical activation and impregnation ratio in chemical activation) on the properties and adsorption capacity of the AC are reviewed. From the results reported in the literature, it can be seen that the influence of the preparation parameters on the adsorption capacity of the prepared AC followed the same pattern. In the physical activation process, microwave power and radiation time have more pronounce effects on the properties of the AC than the activation agent flow rate. Furthermore, the properties of the AC were found to be at their best when the process parameters are at the optimum values wether individually or collectively, and further increase in the process value beyond optimum value resulted in decrease in their adsorption capacity.

scholarly journals Synthesis of activated carbon derived from chicken feather for Li-ion batteries through chemical and physical activation process

2021 ◽  
Vol 10 (3) ◽  
Author(s):  
Erna Hastuti ◽  
Achmad Subhan ◽  
Devi Puspitasari
Keyword(s):  
Activated Carbon ◽  
Low Cost ◽  
Electronic Conductivity ◽  
Lithium Ion ◽  
Interlayer Spacing ◽  
Physical Activation ◽  
Activation Process ◽  
Chicken Feather ◽  
The Difference

AbstractThe use of activated carbon from biomass as an electrode for lithium-ion batteries is promising because of the low cost, natural abundance, and environmentally friendly. Chicken feather is a biomass that has the potential to be a source of activated carbon, because it contains keratin. The activation process affects the quality of activated carbon, thereby increasing battery performance. In this study, chicken feather waste was chemically activated using KOH and combined with physical activation at temperature variations of 750, 850 and 950 °C. The activation process significantly influenced electrochemical properties because of the difference in their microstructure. The activated carbon pyrolyzed at 850 °C (CFCA-850) shows the highest discharge capacity of 285.78 mAhg−1, good cycling stability and rate performance due to its higher interlayer spacing and large surface area. Furthermore, electronic conductivity and ion increase, thus improve battery performance.

Influence of intramolecular interactions on carbon dioxide gas adsorption capacity in Mesoporous Imine polymers

2018 ◽  
Author(s):  
Jaya Prakash Madda ◽  
Pilli Govindaiah ◽  
Sushant Kumar Jena ◽  
Sabbhavat Krishna ◽  
Rupak Kishor
Keyword(s):  
Carbon Dioxide ◽  
Adsorption Capacity ◽  
Density Functional ◽  
Gas Adsorption ◽  
Ambient Pressure ◽  
Condensation Reaction ◽  
Intramolecular Interactions ◽  
Carbon Dioxide Adsorption ◽  
Nitrogen Gas ◽  
Adsorption Characteristic

<p>Covalent organic Imine polymers with intrinsic meso-porosity were synthesized by condensation reaction between 4,4-diamino diphenyl methane and (para/meta/ortho)-phthaladehyde. Even though these polymers were synthesized from precursors of bis-bis covalent link mode, the bulk materials were micrometer size particles with intrinsic mesoporous enables nitrogen as well as carbon dioxide adsorption in the void spaces. These polymers were showed stability up to 260<sup>o</sup> centigrade. Nitrogen gas adsorption capacity up to 250 cc/g in the ambient pressure was observed with type III adsorption characteristic nature. Carbon dioxide adsorption experiments reveal the possible terminal amine functional group to carbamate with CO<sub>2</sub> gas molecule to the polymers. One of the imine polymers, COP-3 showed more carbon dioxide sorption capacity and isosteric heat of adsorption (Q<sub>st</sub>) than COP-1 and COP-2 at 273 K even though COP-3 had lower porosity for nitrogen gas than COP-1 and COP-2. We explained the trends in gas adsorption capacities and Qst values as a consequence of the intra molecular interactions confirmed by Density Functional Theory computational experiments on small molecular fragments.</p>

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals Adsorption of Phenol from Aqueous Solution Using Activated Carbon prepared from Coconut Shell

2017 ◽  
Vol 29 (1) ◽  
pp. 9-13
Author(s):  
Masuma Sultana Ripa ◽  
Rafat Mahmood ◽  
Sabrina Khan ◽  
Easir A Khan
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Iodine Number ◽  
Chemical Engineering ◽  
Coconut Shell ◽  
Physical Activation ◽  
Batch Adsorption ◽  
Adsorption Model ◽  
Solution Ph

Adsorption separation of phenol from aqueous solution using activated carbon was investigated in this work. The adsorbent was prepared from coconut shell and activated by physical activation method. The coconut shell was first carbonized at 800°C under nitrogen atmosphere and activated by CO2 at the same temperature for one hour. The prepared activated carbon was characterized by Scanning Electron Microscope (SEM) and BET Surface Analyzer and by the determination of iodine number as well as Boehm titration. The iodine number indicates the degree of relative activation of the adsorbent. The equilibrium adsorption isotherm phenol from aqueous solution was performed using liquid phase batch adsorption experiments. The effect of experimental parameters including solution pH, agitation time, particle size, temperature and initial concentration was investigated. The equilibrium data was analyzed using Langmuir and Freundlich adsorption model to describe the adsorption isotherm and estimate the adsorption isotherm parameters. The results indicate the potential use of the adsorbent for removal of phenol from the aqueous solution.Journal of Chemical Engineering, Vol. 29, No. 1, 2017: 9-13

Sign in / Sign up

Export Citation Format

Share Document