Luminescence Behavior of Tm3+ Activated GdAlO3 Phosphors Synthesized Using Solid-Reaction Method

2014 ◽  
Vol 602-603 ◽  
pp. 32-37 ◽  
Author(s):  
Nan Wu ◽  
Xiao Dong Li ◽  
Shao Hong Liu ◽  
Yu Dong ◽  
Ji Guang Li ◽  
...  
Keyword(s):  
Decay Curve ◽  
Exchange Interactions ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Nanosized Powders ◽  
Reaction Method ◽  
X Ray ◽  
Pure Phase ◽  
Different Temperatures ◽  
High Color Purity

Trivalent thulium ions (Tm3+) doped GdAlO3 (Gd1-xTmxAlO3) phosphors which show a blue luminescence of high color purity have been synthesized by using solid-state reaction method starting from nanosized powders. X-ray diffraction (XRD) measurements were used to analyze the phase transformations that take place during the preparation of the phosphors. The morphologies of the powders calcined at different temperatures were studied by using scanning electron microscopy (SEM). The luminescence properties of the compounds were investigated. Pure phase of orthorhombic type GdAlO3 (GAP) was yielded by calcining the phosphors at 1200°C for 8 h. The PL spectra showed representative Tm3+ emission. The strong band centered at ~488 nm and the weak one centered at 697 nm were attributed to the 1D2-3F4 and 1G4-3F4 transitions of Tm3+, respectively. The quenching concentration of Tm3+ was estimated to be ~0.75at.% (x=0.0075), for which can be ascribed to the exchange interactions. The decay curve was fitted to be a single exponent and the estimated fluorescent lifetime of the GdAlO3:Tm3+ phosphor was 1.73±0.08 ms.

Structural and Dielectric Properties of Na0.5Bi0.5TiO3 Ferroelectric Ceramics

2012 ◽  
Vol 585 ◽  
pp. 219-223
Author(s):  
Rekha Kumari ◽  
N. Ahlawat ◽  
Ashish Agarwal ◽  
M. Sindhu ◽  
N.N. Ahlawat
Keyword(s):  
Dielectric Properties ◽  
Solid State Reaction Method ◽  
Wide Frequency Range ◽  
Ferroelectric Ceramics ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Different Temperatures

Na0.5Bi0.5TiO3 (NBT) ceramics were synthesized by conventional solid state reaction method. Structural and dielectric properties of these ceramics were investigated. Crystalline phase of sintered ceramics was investigated by X-ray diffraction (XRD). The Rietveld refinement of powder X-ray diffraction revealed that the prepared ceramics exhibit the rhombohedral space group R3c. Dielectric properties of Na0.5Bi0. analyzer.5TiO3 (NBT) ceramics were studied at different temperatures in a wide frequency range using impedance

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

scholarly journals Structure and electric properties of cerium substituted SrBi1.8Ce0.2Nb2O9 and SrBi1.8Ce0.2Ta2O9 ceramics

2016 ◽  
Vol 10 (3) ◽  
pp. 183-188 ◽  
Author(s):  
Mohamed Afqir ◽  
Amina Tachafine ◽  
Didier Fasquelle ◽  
Mohamed Elaatmani ◽  
Jean-Claude Carru ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Solid State ◽  
Room Temperature ◽  
Single Phase ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Lcr Meter ◽  
Curie Temperature Tc

SrBi1.8Ce0.2Nb2O9 (SBCN) and SrBi1.8Ce0.2Ta2O9 (SBCT) powders were prepared via solid-state reaction method. X-ray diffraction analysis reveals that the SBCN and SBCT powders have the single phase orthorhom-bic Aurivillius structure at room temperature. The contribution of Raman scattering and FTIR spectroscopy of these samples were relatively smooth and resemble each other. The calcined powders were uniaxially pressed and sintered at 1250?C for 8 h to obtaine dense ceramics. Dielectric constant, loss tangent and AC conductivity of the sintered Ce-doped SrBi2Nb2O9 and SrBi2Ta2O9 ceramics were measured by LCR meter. The Ce-doped SBN (SBCN) ceramics have a higher Curie temperature (TC) and dielectric constant at TC (380?C and ?? ~3510) compared to the Ce-doped SBT (SBCT) ceramics (330?C and ?? ~115) when measured at 100Hz. However, the Ce-doped SBT (SBCT) ceramics have lower conductivity and dielectric loss.

Thermal enhancement of 2H11/2→4I15/2 up-conversion luminescence of Er3+ doped K2Yb(PO4)(MoO4) phosphors

2021 ◽  
Author(s):  
Hongqiang Cui ◽  
Yongze Cao ◽  
Lei Zhang ◽  
Yuhang Zhang ◽  
Siying Ran ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solid State ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
Orthorhombic Crystal Structure ◽  
Reaction Method ◽  
X Ray ◽  
Thermal Enhancement

Er3+ with different concentrations doped K2Yb(PO4)(MoO4) phosphors were prepared by a solid-state reaction method, and the layered orthorhombic crystal structure of the samples was confirmed by X-ray diffraction (XRD). Under...

Changes in Crystallite Size of Tricalcium Silicate during the Laboratory Grinding

2021 ◽  
Vol 321 ◽  
pp. 23-27
Author(s):  
Simona Ravaszová ◽  
Karel Dvořák
Keyword(s):  
Solid State ◽  
Crystallite Size ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Tricalcium Silicate ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Grinding Time

The paper is focused on one of the most important component of Portland clinker-on the tricalcium silicate. The study reported in this article is focuses on the changes in crystallite size of synthetic tricalcium silicate obtained using solid state reaction method. Crystallite size changes are monitored during the grinding in three types of laboratory mills in two different conditions. Changing in crystallite size at various grinding time up to 120 minutes are studied with the aid of X-ray diffraction and using the Scherrer equation. It has been found that the most efficient laboratory mill in terms of speed and fineness of the material was the planetary mill.

scholarly journals Dielectric and Raman studies of Ba0.06(Na1/2Bi1/2)0.94TiO3–NaNbO3 ceramics

2016 ◽  
Vol 34 (2) ◽  
pp. 437-445 ◽  
Author(s):  
Sumit K. Roy ◽  
S. Chaudhuri ◽  
R.K. Kotnala ◽  
D.K. Singh ◽  
B.P. Singh ◽  
...  
Keyword(s):  
Single Phase ◽  
Solid State Reaction Method ◽  
Lead Free ◽  
Orthorhombic Symmetry ◽  
Dielectric Studies ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
New Phase ◽  
Diffusivity Parameter

AbstractIn this work the X-ray diffraction, scanning electron microscopy, Raman and dielectric studies of lead free perovskite (1 – x)Ba0.06(Na1/2Bi1/2)0.94TiO3–xNaNbO3 (0 ⩽ x ⩽ 1.0) ceramics, prepared using a standard solid state reaction method, were investigated. X-ray diffraction studies of all the ceramics suggested the formation of single phase with crystal structure transforming from rhombohedral-tetragonal to orthorhombic symmetry with the increase in NaNbO3 content. Raman spectra also confirmed the formation of solid solution without any new phase. Dielectric studies showed that the phase transition is of diffusive character and diffusivity parameter decreases with increasing NaNbO3 content. The compositional fluctuation was considered to be the main cause of diffusivity.

scholarly journals Synthesis of Na-Doped Lithium Metatitanate and Its Absorption for Carbon Dioxide

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Liu Zhirong ◽  
Zhang Huan ◽  
Wang Yun ◽  
Zhan Xinxing
Keyword(s):  
Carbon Dioxide ◽  
Solid State Reaction Method ◽  
Absorption Capacity ◽  
Absorption Kinetics ◽  
X Ray Diffraction ◽  
Carbon Dioxide Absorption ◽  
Reaction Method ◽  
X Ray ◽  
Xrd Patterns ◽  
The Relationship

Na-doped lithium metatitanate (Na-doped Li2TiO3) absorbent was doped with Na2CO3and lithium metatitanate (Li2TiO3) was prepared by a solid-state reaction method from mixture of TiO2and Li2CO3. The Na-doped lithium metatitanate was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) and surface area. Carbon dioxide absorption on Na-doped lithium metatitanate was investigated using TG-DTA. The results reveal an increase of the CO2absorption capacity of the Na-doped materials with respect to pure Li2TiO3. XRD patterns of the doped samples suggest a limited substitution of Li by Na atoms within the Li2TiO3structure. The results of experimental and modeling work were summarized to better understand the relationship between the sorbent microstructure and carbon dioxide absorption kinetics.

Superconducting Compound Hg0.8Sb0.2Ba2Ca2Cu3O8+δ Compared with Hg0.8Sb0.2Ba2Ca1Cu2O6+δ to Evaluate Transition Temperature

2020 ◽  
Vol 18 (11) ◽  
pp. 14-18
Author(s):  
Abbas K. Saadon ◽  
Kareem A. Jasim ◽  
Auday H. Shaban
Keyword(s):  
High Temperature ◽  
Transition Temperature ◽  
Solid State ◽  
Solid State Reaction ◽  
Hot Spot ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Superconducting Compound

The high temperature superconductor’s compounds are one of the hot spot field of science, due to their applications in industries. Hg0.8Sb0.2Ba2Ca2Cu3O8+δ and Hg0.8Sb0.2Ba2Ca1Cu2O6+δ, were manufactured using a doable-step of solid state reaction method. The samples were sintered at 800 ° C. The transition temperatures Tc are found from electrically resistively by using four probe techniques. The resistivity become zero when the transition temperature Tc(offset) have 131 and 119 K, and the onset temperature Tc(onset) have 139 K for Hg0.8Sb0.2Ba2Ca2Cu3O8+δ and 132 K for Hg0.8Sb0.2Ba2Ca1Cu2O6+δ. Analysis of X-ray diffraction showed a tetragonal structure with lattice parameters changes for all samples.

Influence of Eu2+ Doped Contents on the Spectroscopic Features of Sr2-X MgSi2O7:xEu2+

2012 ◽  
Vol 476-478 ◽  
pp. 1232-1236
Author(s):  
Jia Zhe Guo ◽  
Ya Dong Li ◽  
Yan Lin Huang
Keyword(s):  
Emission Spectra ◽  
Optical Excitation ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Broad Absorption ◽  
Broad Absorption Band ◽  
Phase Purity ◽  
Reaction Method ◽  
X Ray ◽  
Uv Led

Silicate-based Sr2-xMgSi2O7:xEu2+(x=0.01, 0.03, 0.05, 0.07) phosphors were synthesized by the high temperature solid-state reaction method. Phase purity and crystal structure of the phosphors were characterized using X-ray diffraction spectrometer. The optical excitation and emission spectra of Eu2+ ion were measured using luminescence spectrometer and fluorescence spectrophotometer. The emission spectra showed a strong blue luminescence peaked around 470 nm, corresponds to the 4f65d1 →4f7 transition on Eu2+. Two different average decay time confirmed that the Eu2+ cations may occupy in two different lattice sites and presents different spectroscopic features. With a broad absorption band extending from 224 to 450 nm, it is suggestive that the phosphors have a potential application in UV-LED chips (360-400 nm).

Sign in / Sign up

Export Citation Format

Share Document