Preparation and Properties of Alginate Salt Fibers: An Inherent Flame-Retardant, Biodegradable Fiber

2009 ◽  
Vol 610-613 ◽  
pp. 48-51 ◽  
Author(s):  
Qing Shan Kong ◽  
Quan Ji ◽  
Jian Yu ◽  
Yan Zhi Xia
Keyword(s):  
Tensile Strength ◽  
Flame Retardant ◽  
Oxygen Index ◽  
Natural Fibers ◽  
Fiber Spinning ◽  
Wet Spinning ◽  
Release Rates ◽  
Combustion Property ◽  
Alginate Fiber ◽  
Limited Oxygen

Alginate calcium fibers were prepared through wet spinning with good tensile strength which can be used for cloth materials. The morphology, mechanical property and combustion property of alginate calcium fibers were investigated. Blending yarns and textile of alginate calcium fibers and combed cotton was fabricated with good hand feeling and strength. Alginate salt fiber was prepared with wet spinning machine designed according to viscose fiber spinning machine. The diameter of alginate calcium fibers was about 10-15µm in diameter with smooth surface. The tensile strength of alginate salt fiber was larger than 4.8 cN in the dry state. The value of Limited Oxygen Index (LOI) of alginate calcium fibers was 34%. The average heat release rates (HRR) of the alginate fiber is about 21 kW/m2 which was much lower than that of most synthetic and natural fibers analysized with Cone. Alginate calcium fibers is an inherent flame-retardant fiber.

Influence of Intumescent Flame Retardant on Flammability and Tensile Behavior of Oil-Extended SEBS

2013 ◽  
Vol 749 ◽  
pp. 65-70
Author(s):  
Xiao Yan Li ◽  
Yan Chun Li ◽  
Chen Jie Shi ◽  
Si Si Cai ◽  
Xia Wang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Flame Retardant ◽  
Oxygen Index ◽  
Intumescent Flame Retardant ◽  
Degradation Behavior ◽  
Char Layer ◽  
Micro Holes ◽  
Ul 94 ◽  
Limited Oxygen

A kind of intumescent flame retardant (IFR) were used for flame retarding of oil-extended hydrogenated styrene-butylenes-styrene (O-SEBS). The samples were systemically characterized by limited oxygen index (LOI), vertical burning test (UL-94), and scanning electron microscopy (SEM); Thermogravimetric (TG) analysis. The results showed that the IFR retardant can promote residual chars with multi-micro holes on the surface of SEBS to inhibit flame; with 45% IFR content, the LOI is 28.3 and flame retardant level is UL-94 classification of V-0, with no dripping. The morphological structures observed by SEM demonstrated that higher IFR content promote to form larger and compact films cover on bubbles of the intumescent char layer. The TG data revealed that the IFR could change the degradation behavior of the O-SEBS, enhance the thermal stability and increase the char residue, The tensile strength of all the O-SEBS/IFR blends had the tensile strength of more than 4MPa and the elongation of more than 850%.

scholarly journals Effects of collagen fiber addition on the combustion and thermal stability of natural rubber

2020 ◽  
Vol 2 (1) ◽  
Author(s):  
Weixing Xu ◽  
Xintao Wu ◽  
Qilin Wen ◽  
Shuangyang Li ◽  
Yongjiao Song ◽  
...  
Keyword(s):  
Natural Rubber ◽  
Flame Retardant ◽  
Nitrogen Content ◽  
Flame Retardancy ◽  
Collagen Fiber ◽  
Oxygen Index ◽  
Air Pockets ◽  
Thermal Stability Of ◽  
Limited Oxygen ◽  
Properties Of Composites

Abstract Collagen fiber (CF) and silane coupling agent-modified collagen fiber (MCF) were used as flame retardant filler for natural rubber (NR) modification. The combustion phenomena and properties of composites blended with different dosages of CF or MCF were compared to elucidate the flame retardant mechanism of the composites. The flame retardancy of NR can be enhanced effectively by increasing nitrogen content (the nitrogen content of CF is about 18%), creating air pockets, and structuring the flame retardant network in the composites. MCF failed to structure a flame retardant network in the composite, indicating that its modification effects of MCF are weaker than those of CF. When CF dosage was 30 wt%, the composite can achieve the best flame retardancy, with limited oxygen index of 29.4% and without smoke and dripping during burning. This study demonstrated a new method for the flame retardant modification of NR. Graphical abstract

Flame-retardant behaviors of aluminum phosphates coated sepiolite in epoxy resin

2020 ◽  
pp. 073490412093408
Author(s):  
Wei Yan ◽  
Pu Xie ◽  
Zhengwei Yang ◽  
Guangjin Luo ◽  
Weijiang Huang ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Oxygen Index ◽  
One Pot ◽  
Heterogeneous Precipitation ◽  
Aluminum Phosphates ◽  
Thermal Stability Of ◽  
Limited Oxygen

Aluminum phosphates coated sepiolite nanocomposite was fabricated via a simple one-pot heterogeneous precipitation strategy, and the effects of aluminum phosphates on the morphology of aluminum phosphates coated sepiolite were investigated. Moreover, the effect of aluminum phosphates coated sepiolite on the flame-retardant behavior, mechanical properties, and thermal stability of epoxy resin have been discussed. The results indicated that the introduction of only 20 wt% aluminum phosphates coated sepiolite in epoxy resin increased the limited oxygen index from 21.8% to 30.1%, thus the material met the UL-94 V-0 rating. Thermogravimetric analyses revealed that char yield increased in the presence of aluminum phosphates coated sepiolite form thermally stable carbonaceous char. Aluminum phosphates–coated sepiolite could improve the mechanical performance, thermal stability of epoxy resin.

Tensile and flammability characterizations of corn straw slagging/high-density polyethylene composites

2019 ◽  
Vol 33 (11) ◽  
pp. 1466-1477
Author(s):  
Qingfa Zhang ◽  
Wenyu Lu ◽  
Liang Zhou ◽  
Donghong Zhang ◽  
Hongzhen Cai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Flame Retardant ◽  
High Density Polyethylene ◽  
Oxygen Index ◽  
High Density ◽  
Corn Straw ◽  
Scanning Calorimetry ◽  
Scanning Electron

Biocomposites were prepared with corn straw slagging (CSS) and high-density polyethylene (HDPE) at four loading levels (10, 20, 30, and 40 wt%) by extrusion method. CSS/HDPE composites were tested by tension, oxygen index meter, differential scanning calorimetry, X-ray diffraction, and the scanning electron microscopy. The scanning electron microscopy showed that CSS was dispersed uniformly in the HDPE matrix and strong interfacial interaction was achieved, which had an important influence on the tensile strength of the composites. The tensile strength of the composites could be improved with proper increase of CSS and reached maximum value at 30 wt% content. Furthermore, the addition of CSS played an important role in improving the flame-retardant ability of CSS/HDPE composites, and the limited oxygen index was 31.26% at 40 wt% content, good flame-retardant effect achieved.

Flame retardancy and thermal properties of rigid polyurethane foam conjugated with a phosphorus–nitrogen halogen-free intumescent flame retardant

2020 ◽  
Vol 38 (3) ◽  
pp. 235-252
Author(s):  
Zhaojun Lin ◽  
Qianqiong Zhao ◽  
Ruilan Fan ◽  
Xiaoxue Yuan ◽  
Fuli Tian
Keyword(s):  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Flame Retardant ◽  
Polyurethane Foam ◽  
Flame Retardancy ◽  
Oxygen Index ◽  
Carbon Layer ◽  
Limited Oxygen Index ◽  
Halogen Free ◽  
Limited Oxygen

In this work, a halogen-free intumescent combining phosphorus and nitrogen, flame-retardant 2-((2-hydroxyphenyl)(phenylamino)methyl5,5-dimethyl-1,3,2-dioxaphosphinane 2-oxide (HAPO) was successfully synthesized. It had been synthesized by reaction of 5,5-dimethyl-1,3, 2-dioxphosphinane 2-oxide with Schiff base. Its chemical structure was characterized in detail by Fourier transform infrared spectroscopy, 1H NMR, and 31P NMR spectrum. The flame-retardant polyurethanes were prepared with different loadings of HAPO. The thermal properties, flame retardancy and combustion behavior of the pure polyurethane foam thermosets were investigated by a series of measurements involving thermogravimetric analysis, limited oxygen index measurement, UL-94 vertical burning test, and cone calorimeter test. The results of the aforementioned tests indicated that HAPO can significantly improve the flame retardancy as well as smoke inhibition performance of polyurethane foam. Compared with the PU-Neat, the limited oxygen index of flame-retardant polyurethanes (15%) thermoset was increased from 19.5% to 23.8% and its UL-94 reached V-0 rating. In addition, the cone test results showed that the heat release rate, total heat release, rate of smoke release, and total smoke production of flame-retardant polyurethanes (10%) were decreased obvious sly. The apparent morphology of carbon residue was characterized by scanning electron microscopy, and results revealed that the modified polyurethane foam can form dense carbon layer after combustion. Thermogravimetric analysis results also indicated that the char amount of flame-retardant polyurethanes was obviously increased compared with PU-Neat. Based on the above analysis, we can draw the conclusions which in the condensed phase, phosphorus-based acids from the degradation of HAPO, this could promote the formation of continuous and dense phosphorus-rich carbon layer. In the gas phase, the flame-retardant mechanism was ascribed to the quenching effect of phosphorus-based radicals and diluting effect by non-flammable gases.

Synergistic Effect between Montmorillonite Intercalated by Melamine and Intumescent Flame Retardant (IFR) on Polypropylene

2011 ◽  
Vol 295-297 ◽  
pp. 315-318
Author(s):  
Hong Fang Zhu ◽  
Juan Li ◽  
Liang Xu ◽  
Kang Tao ◽  
Li Xin Xue ◽  
...  
Keyword(s):  
Synergistic Effect ◽  
Flame Retardant ◽  
Cone Calorimeter ◽  
Oxygen Index ◽  
Intumescent Flame Retardant ◽  
Limited Oxygen Index ◽  
Cation Exchange Reaction ◽  
Melamine Salt ◽  
Better Than ◽  
Limited Oxygen

This Montmorillonite modified by melamine (MA-MMT) was prepared via cation exchange reaction by using melamine salt as intercalation reagent. MA-MMT and Na-MMT was combined with intumescent flame retardant (IFR) to be adopted into polypropylene (PP), respectively. The synergistic effect between MA-MMT and IFR and the influence of melamine in MMT layers on fire-resistant performance was evaluated. Results of limited oxygen index (LOI) tests and UL-94 tests indicate that melamine salts in MMT layers behaved better than Na-MMT in PP/IFR system. According to the results of cone calorimeter tests and scanning electron microscope (SEM), it concludes that melamine salts act as gas agent to provide migration impetus and expanded power, which caused a well-structured and strong char that had better ability to endure heat erosion. A good synergistic effect between MA-MMT and IFR is constructed.

Flame-Retardant Properties of Polyester Fabrics Reinforced Phenolic Resin Modified with Silazanes Composites

2015 ◽  
Vol 1120-1121 ◽  
pp. 519-522
Author(s):  
Xiao Wen Ren ◽  
Ya Ping Zhu ◽  
Fan Wang ◽  
Hui Min Qi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Flame Retardant ◽  
Phenolic Resin ◽  
Oxygen Index ◽  
Phenolic Resins ◽  
Polyester Fabrics ◽  
Limited Oxygen Index ◽  
Flame Retardant Properties ◽  
Limited Oxygen

Phenolic resin modified with methylvinylcyclosilazanes (MVSZ) were prepared and their flame-retardant properties were investigated, and results exhibited that the Limited Oxygen Index (LOI) values increased with the content increasing of MVSZ, and the LOI reach to 40.8, when the content of MVSZ was 26.0%. The flame-retardant and mechanical properties of polyester fabrics reinforced phenolic resin modified with silazanes (PFMS) composites were measured, the results indicated that the LOI and flexural strength were enhanced compared with those of phenolic resins composites.

Preparation and Properties of Tapioca Starch-Banana Fiber Composites Modified with Magnesium Hydroxide

2011 ◽  
Vol 194-196 ◽  
pp. 1707-1710
Author(s):  
Xian Zhong Mo ◽  
Xiang Qi ◽  
Yu Xiang Zhong ◽  
Ren Huan Li ◽  
Chen Mo
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Hydroxide ◽  
Oxygen Index ◽  
Fiber Composites ◽  
Banana Fiber ◽  
Tapioca Starch ◽  
Limited Oxygen Index ◽  
Mechanical Properties Testing ◽  
Limited Oxygen

Banana fiber/tapioca starch (BFRTPS) composites modified by magnesium hydroxide (Mg(OH)2) were prepared with glycerin as the plasticizer, banana fiber as reinforcement and thermoplastic tapioca starch as matrix. Rheological properties testing showed that Mg(OH)2take a strong effect to the preparation processing and made it hard to mix while the content increasing. Mechanical properties testing revealed that at the range of the Mg(OH)2content from 5 to 20phr, the tensile strength of the composites increased from 12.8MPa to 24.8MPa at 15phr Mg(OH)2content, but its elastic modulus was increased with the increasing of Mg(OH)2, reached the maximum of 3100MPa at 20phr Mg(OH)2content. Obviously, Mg(OH)2has an enforced effect to the composites. Combustion performances of the composites was improved by Mg(OH)2, the limited oxygen index(LOI) of the composites reached to 31% while the content of Mg(OH)2was 20phr, and then the result of flammability testing achieved UL94HF-1 and UL94 V-0 level.

Synthesis of a Flame Retardant for Epoxy Resins: Thermal Stability, Flame Retardancy, and Flame-Retardant Modes

2021 ◽  
Vol 36 (2) ◽  
pp. 172-184
Author(s):  
Y. Zhang ◽  
J. Liu ◽  
S. Li
Keyword(s):  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Heat Release ◽  
Flame Retardant ◽  
Photoelectron Spectroscopy ◽  
Epoxy Resins ◽  
Oxygen Index ◽  
Limited Oxygen Index ◽  
Index Value ◽  
Limited Oxygen

Abstract A polyphosphonate (PDPA) flame retardant that contains phenyl phosphonic dichloride and 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide groups, has been synthesized. The flame retardant was introduced into epoxy resins (EP) and cured by 4,4’-diamino diphenylmethane. The vertical burning, limited-oxygen index and cone calorimeter tests reveal that the PDPA can enhance the flame-retardant properties of the EP significantly. With only a 4 wt% PDPA loading, the EP composites achieved a limited-oxygen index value of 33.4% and a V-0 rating in the vertical burning test, and the peak heat release rate and total heat release were decreased by 40.9% and 24.6%, respectively. The thermal properties and gas pyrolysis products of the EP composites were evaluated by thermogravimetric analysis and thermogravimetric analysis-Fourier transform infrared spectroscopy, and the morphology and structure of residual char were characterized by scanning electron microscopy, Flourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. To explain the combined effects of the condensed and gas phases, modes of the flame-retardant action are proposed.

scholarly journals Preparing the Degradable, Flame-Retardant and Low Dielectric Constant Nanocomposites for Flexible and Miniaturized Electronics with Poly(lactic acid), Nano ZIF-8@GO and Resorcinol Di(phenyl phosphate)

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1756 ◽  
Author(s):  
Mi Zhang ◽  
Yu Gao ◽  
Yixing Zhan ◽  
Xiaoqing Ding ◽  
Ming Wang ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Lactic Acid ◽  
Flame Retardant ◽  
Oxygen Index ◽  
Nanocomposite Films ◽  
Low Dielectric Constant ◽  
Poly Lactic Acid ◽  
Phenyl Phosphate ◽  
Low Dielectric ◽  
Limited Oxygen

Degradable, flame retardant, and flexible nanocomposite films with low dielectric constant were prepared with poly (lactic acid) (PLA), nano ZIF-8@GO, and degradable flame-retardant resorcinol di(phenyl phosphate) (RDP). The SEM results of the fractured surfaces indicated that ZIF-8@GO and RDP were dispersed uniformly in the PLA matrix. The prepared films had good mechanical properties and the tensile strength of the film with 1.5 wt% of ZIF-8@GO was increased to 48.2 MPa, compared with 38.5 MPa of pure PLA. Meanwhile, the nanocomposite films were flexible due to the toughing effect of RDP. Moreover, above 27.0% of limited oxygen index (LOI) and a VTM-0 rating were achieved for the nanocomposite films. The effects of nano ZIF-8@GO hybrids and RDP on the dielectric properties were investigated, and the results showed that ZIF-8@GO and RDP were beneficial in reducing the dielectric constant and dielectric loss of the nanocomposites.

Sign in / Sign up

Export Citation Format

Share Document