Microstructure and Properties of a Fe-Cu Composite Processed by HPT Powder Consolidation

2010 ◽  
Vol 667-669 ◽  
pp. 229-234 ◽  
Author(s):  
Andrea Bachmaier ◽  
Reinhard Pippan
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
High Pressure ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Step Process ◽  
Powder Consolidation ◽  
Grain Sizes ◽  
Scanning Electron

A method to produce nanocrystalline Fe-Cu composites by means of high-pressure torsion (HPT) deformation is presented. Mixtures of micrometer sized powders of Fe and Cu with different ratios of the two components were precompacted and subsequently deformed by HPT at room temperature to a certain amount of strain. Afterwards, new samples were cut out of these previously deformed samples and further HPT deformation was conducted. The evolution of the microstructure during the different steps of the HPT process and the resulting microstructure of the composites were investigated by scanning electron microscopy. In summary it could be shown that the final attainable grain sizes in the composite materials in the two step process are much smaller than in the simply HPT deformed composites. The reduction of the grain size is also reflected in an enhancement of the hardness.

Effects of Ca and Y on Microstructures and Mechanical Properties of Magnesium Alloy AZ81

2014 ◽  
Vol 488-489 ◽  
pp. 154-157
Author(s):  
Lei Lei Chen ◽  
Quan An Li ◽  
Jiang Chang Xie
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Room Temperature ◽  
Microstructure And Mechanical Properties ◽  
Mechanical Properties Testing ◽  
Microstructures And Mechanical Properties ◽  
Scanning Electron

By the scanning electron microscopy, the microstructure and mechanical properties testing, the effect of Ca and Y on the microstructure and mechanical properties of magnesium alloy AZ81 are investigated in this paper. The results show that with Ca and Y addition, the grain size is refined. And with the β-Mg17Al12 phase reducing significantly, there will be the precipitation of Al2Ca and Al2Y. Meanwhile, the mechanical properties of AZ81 magnesium alloy are enhanced at room temperature and 150°C.

Microstructures and Creep Properties of Mg-2.5Zn-xCe (x = 4, 6 and 8 mass%) Alloys

2015 ◽  
Vol 34 (3) ◽  
Author(s):  
Z.H. Chen ◽  
W. Wang ◽  
D. Chen ◽  
W.J. Xia
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Phase Composition ◽  
Tensile Stress ◽  
Room Temperature ◽  
Tensile Creep ◽  
Creep Properties ◽  
X Ray ◽  
Grain Sizes ◽  
Scanning Electron

AbstractThe effect of 4, 6 and 8 (mass%) Ce additions on the microstructure and creep resistance of the Mg-2.5Zn alloy was investigated by tensile creep test in the temperature of 200 °C, 225°C with the tensile stress of 60 MPa and tensile test in room temperature. The microstructure and phase composition of these alloys were analyzed by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffractometry (XRD). The results showed that the grain sizes of Mg-2.5Zn-

Scanning Electron Microscopy-cuticular Lesions on the Roundworm Ascaris Suum

1970 ◽  
Vol 28 ◽  
pp. 114-115
Author(s):  
P. A. Madden ◽  
W. R. Anderson
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Freeze Drying ◽  
Room Temperature ◽  
Secondary Electron ◽  
Distilled Water ◽  
Freeze Dried ◽  
Silver Paint ◽  
To Come ◽  
Scanning Electron

The intestinal roundworm of swine is pinkish in color and about the diameter of a lead pencil. Adult worms, taken from parasitized swine, frequently were observed with macroscopic lesions on their cuticule. Those possessing such lesions were rinsed in distilled water, and cylindrical segments of the affected areas were removed. Some of the segments were fixed in buffered formalin before freeze-drying; others were freeze-dried immediately. Initially, specimens were quenched in liquid freon followed by immersion in liquid nitrogen. They were then placed in ampuoles in a freezer at −45C and sublimated by vacuum until dry. After the specimens appeared dry, the freezer was allowed to come to room temperature slowly while the vacuum was maintained. The dried specimens were attached to metal pegs with conductive silver paint and placed in a vacuum evaporator on a rotating tilting stage. They were then coated by evaporating an alloy of 20% palladium and 80% gold to a thickness of approximately 300 A°. The specimens were examined by secondary electron emmission in a scanning electron microscope.

SEM Observations on the Germination of Euonymous Americanus

1985 ◽  
Vol 43 ◽  
pp. 508-509
Author(s):  
D.R. Hill ◽  
J.R. McCurry ◽  
L.P. Elliott ◽  
G. Howard
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Light Microscopy ◽  
Filter Paper ◽  
Room Temperature ◽  
Food Source ◽  
Environmental Chamber ◽  
Dormant Stage ◽  
Scanning Electron

Germination of Euonymous americanus in the laboratory has previously been unsuccessful. Ability to germinate Euonymous americanus. commonly known as the american strawberry bush, is important in that it represents a valuable food source for the white-tailed deer. Utilizing the knowledge that its seeds spend a period of time in the rumin fluid of deer during their dormant stage, we were successful in initiating germination. After a three month drying period, the seeds were placed in 25 ml of buffered rumin fluid, pH 8 at 40°C for 48 hrs anaerobically. They were then allowed to dry at room temperature for 24 hrs, placed on moistened filter paper and enclosed within an environmental chamber. Approximately four weeks later germination was detected and verified by scanning electron microscopy; light microscopy provided inadequate resolution. An important point to note in this procedure is that scarification, which was thought to be vital for germination, proved to be unnecessary for successful germination to occur. It is believed that germination was propagated by the secretion of enzymes or prescence of acids produced by microorganisms found in the rumin fluid since sterilized rumin failed to bring about germination.

Scattering of Electrons at High - Pressure and Restoration of Image Contrast in High Pressure Scanning Electron Microscopy

1990 ◽  
Vol 48 (1) ◽  
pp. 384-385
Author(s):  
J. S. Shah ◽  
R. Durkin ◽  
A. N. Farley
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Pressure ◽  
Cross Sections ◽  
Single Scattering ◽  
Image Contrast ◽  
Experimental Scheme ◽  
Medium Resolution ◽  
Scattering Approximation ◽  
Scanning Electron

It is now possible to perform High Pressure Scanning Electron Microscopy (HPSEM) in the range 10 to 2000 Pa. Here the effect of scattering on resolution has been evaluated by calculating the profile of the beam in high pressure and assessing its effect on the image contrast . An experimental scheme is presented to show that the effect of the primary beam ionization is to reduce image contrast but this effect can be eliminated by a novel use of specimen current detection in the presence of an electric field. The mechanism of image enhancement is discussed in terms of collection of additional carriers generated by the emissive components.High Pressure SEM (HPSEM) instrumentation is establishing itself as commercially viable. There are now a number of manufacturers, such as JEOL, ABT, ESCAN, DEBEN RESEARCH, selling microscopes and accessories for HPSEM. This is because high pressure techniques have begun to yield high quality micrographs at medium resolution.To study the effect of scattering on the incident electron beam, its profile - in a high pressure environment - was evaluated by calculating the elastic and inelastic scattering cross sections for nitrogen in the energy range 5-25 keV. To assess the effect of the scattered beam on the image contrast, the modification of a sharp step contrast function due to scattering was calculated by single scattering approximation and experimentally confirmed for a 20kV accelerated beam.

scholarly journals Effect of triple junctions on deformation twinning in a nanostructured Cu–Zn alloy: A statistical study using transmission Kikuchi diffraction

2016 ◽  
Vol 7 ◽  
pp. 1501-1506
Author(s):  
Silu Liu ◽  
Xiaolong Ma ◽  
Lingzhen Li ◽  
Liwen Zhang ◽  
Patrick W Trimby ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Statistical Study ◽  
Nanocrystalline Material ◽  
High Pressure Torsion ◽  
Triple Junctions ◽  
Step Size ◽  
Deformation Twins ◽  
Zn Alloy ◽  
Scanning Electron

Scanning electron microscopy transmission Kikuchi diffraction is able to identify twins in nanocrystalline material, regardless of their crystallographic orientation. In this study, it was employed to characterize deformation twins in Cu/10 wt % Zn processed by high-pressure torsion. It was found that in 83% of grains containing twins, at least one twin intersects with a triple junction. This suggests that triple junctions could have promoted the nucleation of deformation twins. It should be cautioned that this technique might be unable to detect extremely small nanoscale twins thinner than its step size.

The Processing of Ultrafine-Grained Materials Using High-Pressure Torsion

2007 ◽  
Vol 558-559 ◽  
pp. 1283-1294 ◽  
Author(s):  
Cheng Xu ◽  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
High Pressure Torsion ◽  
Metallic Materials ◽  
Grain Sizes ◽  
Ultrafine Grained ◽  
Wide Range ◽  
Ultrafine Grained Materials ◽  
Thin Disks

It is now well-established that processing through the application of severe plastic deformation (SPD) leads to a significant reduction in the grain size of a wide range of metallic materials. This paper examines the fabrication of ultrafine-grained materials using high-pressure torsion (HPT) where this process is attractive because it leads to exceptional grain refinement with grain sizes that often lie in the nanometer or submicrometer ranges. Two aspects of HPT are examined. First, processing by HPT is usually confined to samples in the form of very thin disks but recent experiments demonstrate the potential for extending HPT also to bulk samples. Second, since the strains imposed in HPT vary with the distance from the center of the disk, it is important to examine the development of inhomogeneities in disk samples processed by HPT.

Identification of Nd163 phase in melt-textured NdBa2Cu3O7−δ bulk samples

2003 ◽  
Vol 18 (9) ◽  
pp. 2050-2054 ◽  
Author(s):  
Marcello Gombos ◽  
Vicente Gomis ◽  
Anna Esther Carrillo ◽  
Antonio Vecchione ◽  
Sandro Pace ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Room Temperature ◽  
Polarized Light ◽  
Energy Dispersive ◽  
X Ray ◽  
Spontaneous Formation ◽  
The Stability ◽  
Scanning Electron

In this work, we report on the observation of Nd1Ba6Cu3O10,5 (Nd163) phase of the NdBaCuO system in melt-textured Nd123 bulk samples grown from a mixture of Nd123 and Nd210 phase powders. The observation was performed with polarized light optical microscopy and scanning electron microscopy–energy dispersive x-ray analyses. Images of the identified phase crystals show an aspect quite different from Nd422 crystals. Unexpectedly, Nd163 was individuated, even in “pure” Nd123 samples. Moreover, after long exposure to air, Nd163 disappeared completely in samples synthesized from powders containing Nd210. Thermogravimetry analyses of powders show that the stability of this phase in air is limited to temperatures higher than 900 °C, so Nd163 is unstable and highly reactive at room temperature. Moreover, an explanation of the observation of Nd163 in Nd210 free samples, based on the spontaneous formation of Nd163 phase in a Nd123 melt, is proposed.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Sign in / Sign up

Export Citation Format

Share Document