Multi-Level Trap Assisted Tunneling Model for the Field and Temperature Dependence of SiC-JBS Reverse Leakage Current

2018 ◽  
Vol 924 ◽  
pp. 601-604 ◽  
Author(s):  
Gary Dolny ◽  
Yang Sheng ◽  
Yue Fu ◽  
S. Li ◽  
Rahul Radhakrishnan ◽  
...  
Keyword(s):  
Leakage Current ◽  
Thermionic Emission ◽  
Tunneling Model ◽  
Reverse Leakage Current ◽  
Current Voltage ◽  
Wide Range ◽  
Trap Assisted Tunneling ◽  
Current Voltage Characteristics ◽  
Multi Level ◽  
Assisted Tunneling

The reverse-bias current-voltage characteristics of commercial 1200 V 4H-silicon-carbide junction barrier Schottky (SiC-JBS) rectifiers are studied both experimentally and through numerical simulation. The reverse leakage current measured from physical devices is observed to display both a strong temperature and field dependence. A model is presented to explain the observed behavior based on a combination of trap-assisted tunneling and a thermionic-emission mechanism through a potential barrier located at the metal-SiC interface. The study shows that a two-level trapping model can be necessary to properly explain the measured data. Excellent agreement between the models and the measurements is obtained over a wide range of bias and temperature.

I - V Characteristics in Surface-Activated Bonding (SAB) Based Si/SiC Junctions at Raised Ambient Temperatures

2014 ◽  
Vol 778-780 ◽  
pp. 718-721 ◽  
Author(s):  
Shota Nishida ◽  
Jian Bo Liang ◽  
Masashi Morimoto ◽  
Naoteru Shigekawa ◽  
Manabu Arai
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electrical Properties ◽  
Reverse Bias ◽  
Tunneling Model ◽  
Ambient Temperatures ◽  
Current Voltage ◽  
Trap Assisted Tunneling ◽  
Assisted Tunneling ◽  
Scanning Electron

The physical and electrical properties of p+-Si/n-4H-SiC and n+-Si/n-4H-SiC heterojunctions fabricated by using surface-activated bonding (SAB) were investigated by scanning electron microscopy (SEM), current-voltage (I-V) and breakdown characteristics measurements at raised ambient temperatures. The I-V characteristics for the reverse bias voltages of the two junctions were compared with the expectations based on Frenkel-Poole, and trap-assisted tunneling models. The results of calculations using the trap-assisted tunneling model were close to the measurements.

A recombination- and trap-assisted tunneling model for stress-induced leakage current

2001 ◽  
Vol 45 (8) ◽  
pp. 1361-1369 ◽  
Author(s):  
Daniele Ielmini ◽  
Alessandro S. Spinelli ◽  
Andrea L. Lacaita ◽  
Andrea Martinelli ◽  
Gabriella Ghidini
Keyword(s):  
Leakage Current ◽  
Tunneling Model ◽  
Trap Assisted Tunneling ◽  
Assisted Tunneling ◽  
Stress Induced Leakage Current

Ar Annealing at 1600°C and 1650°C of Al+ Implanted p+/n 4H-SiC Diodes: Analysis of the J-V Characteristics Versus Annealing Temperature

2005 ◽  
Vol 483-485 ◽  
pp. 625-628 ◽  
Author(s):  
Fabio Bergamini ◽  
Francesco Moscatelli ◽  
Mariaconcetta Canino ◽  
Antonella Poggi ◽  
Roberta Nipoti
Keyword(s):  
Leakage Current ◽  
Leakage Current Density ◽  
Current Density ◽  
Electrical Characterization ◽  
Reverse Leakage Current ◽  
Current Voltage ◽  
Exponential Trend ◽  
Current Voltage Characteristics ◽  
Post Implantation

We report on the electrical characterization of Al+ implanted p+/n 4H-SiC diodes via a planar technology. Hot implantation at 400°C and post implantation annealing at 1600°C and 1650°C in high purity Argon ambient were done for the realization of p+/n diodes. The current voltage characteristics of the p+/n diodes and the resistivity of the implanted layer were measured at room temperature. The majority of the 136 measured diodes had a turn on voltage of 1.75 V for both annealing temperatures. The 1600°C annealed diodes showed an almost exponential forward characteristic with ideality factor equal to 1.4, an average reverse leakage current density equal to (4.8 ± 0.1)×10-9 A/cm2 at –100 V, and a break down voltage between 600 and 900V. The 1650°C annealed diodes often had forward “excess current component” that deviates from the ideal forward exponential trend. The average reverse leakage current density was equal to (2.7 ± 0.5)×10-8 A/cm2 at –100 V, and the breakdown voltage was between 700 and 1000V, i.e. it approached the theoretical value for the epitaxial 4H-SiC layer.

APPLICATION OF EPITAXIAL UNIPOLAR BARRIERS TO REDUCE NOISE CURRENTS IN PHOTODETECTORS

2011 ◽  
Vol 20 (03) ◽  
pp. 557-564
Author(s):  
G. R. SAVICH ◽  
J. R. PEDRAZZANI ◽  
S. MAIMON ◽  
G. W. WICKS
Keyword(s):  
Leakage Current ◽  
Surface Passivation ◽  
Leakage Currents ◽  
Type Region ◽  
Surface Leakage Current ◽  
Unipolar Barrier ◽  
Trap Assisted Tunneling ◽  
Assisted Tunneling ◽  
Tunneling Currents ◽  
Surface Leakage

Tunneling currents and surface leakage currents are both contributors to the overall dark current which limits many semiconductor devices. Surface leakage current is generally controlled by applying a post-epitaxial passivation layer; however, surface passivation is often expensive and ineffective. Band-to-band and trap assisted tunneling currents cannot be controlled through surface passivants, thus an alternative means of control is necessary. Unipolar barriers, when appropriately applied to standard electronic device structures, can reduce the effects of both surface leakage and tunneling currents more easily and cost effectively than other methods, including surface passivation. Unipolar barriers are applied to the p -type region of a conventional, MBE grown, InAs based pn junction structures resulting in a reduction of surface leakage current. Placing the unipolar barrier in the n -type region of the device, has the added benefit of reducing trap assisted tunneling current as well as surface leakage currents. Conventional, InAs pn junctions are shown to exhibit surface leakage current while unipolar barrier photodiodes show no detectable surface currents.

Structural and Electrical Characterization of Si-Implanted TiN as a Diffusion Barrier for Cu Metallization

1995 ◽  
Vol 391 ◽  
Author(s):  
W.F. Mcarthur ◽  
K.M. Ring ◽  
K.L. Kavanagh
Keyword(s):  
Leakage Current ◽  
Diffusion Barrier ◽  
Depth Profiling ◽  
Electrical Characterization ◽  
Implantation Dose ◽  
Cu Metallization ◽  
Reverse Leakage Current ◽  
Transmission Electron ◽  
Current Voltage

AbstractThe feasibility of Si-implanted TiN as a diffusion barrier between Cu and Si was investigated. Barrier effectiveness was evaluated via reverse leakage current of Cu/TixSiyNz/Si diodes as a function of post-deposition annealing temperature and time, and was found to depend heavily on the film composition and microstructure. TiN implanted with Si28, l0keV, 5xl016ions/cm2 formed an amorphous ternary TixSiyNz layer whose performance as a barrier to Cu diffusion exceeded that of unimplanted, polycrystalline TiN. Results from current-voltage, transmission electron microscopy (TEM), and Auger depth profiling measurements will be presented. The relationship between Si-implantation dose, TixSiyNz structure and reverse leakage current of Cu/TixSiyNz/Si diodes will be discussed, along with implications as to the suitability of these structures in Cu metallization.

Study on Schottky Diode Characteristics Improving by X-Ray Irradiation

2013 ◽  
Vol 717 ◽  
pp. 113-116
Author(s):  
Sani Klinsanit ◽  
Itsara Srithanachai ◽  
Surada Ueamanapong ◽  
Sunya Khunkhao ◽  
Budsara Nararug ◽  
...  
Keyword(s):  
Leakage Current ◽  
Schottky Diode ◽  
Room Temperature ◽  
The Other ◽  
Low Power Consumption ◽  
Initial Value ◽  
X Ray ◽  
Forward Current ◽  
Current Voltage ◽  
Current Voltage Characteristics

The effect of soft X-ray irradiation to the Schottky diode properties was analyzed in this paper. The built-in voltage, leakage current, and work function of Schottky diode were investigated. The current-voltage characteristics of the Schottky diode are measured at room temperature. After irradiation at 70 keV for 55 seconds the forward current and leakage current are increase slightly. On the other hand, the built-in voltage is decrease from the initial value about 0.12 V. Consequently, this method can cause the Schottky diode has low power consumption. The results show that soft X-ray can improve the characteristics of Schottky diode.

Sign in / Sign up

Export Citation Format

Share Document