scholarly journals Boron fractionation in some Saskatchewan soils

2002 ◽  
Vol 82 (2) ◽  
pp. 173-179 ◽  
Author(s):  
M. Raza ◽  
A R Mermut ◽  
J J Schoenau ◽  
S S Malhi
Keyword(s):  
Small Proportion ◽  
Correlation Coefficients ◽  
Good Method ◽  
Exchange Capacity ◽  
Water Soluble ◽  
Hot Water ◽  
Potential Contribution ◽  
Organic Carbon Content ◽  
Anion Exchange Membranes ◽  
Soil Extraction

Knowledge of B fractions is essential for understanding its chemistry and potential contribution to plant uptake. Four different extraction methodologies to determine readily available B were compared, using a four-step sequential B fractionation procedure, to reveal the nature of soil B in nine selected soils from the Brown and Gray Luvisol zones with different textures and management histories. The four soil extraction techniques were: hot water (HW), 0.01M CaCl2, 1 M NH4-acetate and anion exchange membranes (AEM). The other four fractions, specifically adsorbed, oxide bound, organically bound, and residual B were determined sequentially on the same soil samples. On average, HW extracted more B than 0.01M CaCl2, 1 M NH4-acetate, and AEM. In almost every soil, readily soluble B represented only a small proportion of the total B content, regardless of the extraction method used. Most soil B existed in the residual or occluded form, which accounted for between 92 and 99%, with an average of 97%, of the total soil B. The concentration of organically bound B was higher than that of oxide bound B and specifically adsorbed B, irrespective of the readily soluble B extracting solution used. Cation exchange capacity (CEC) appeared to be an important characteristic to predict the B pools. No significant correlation was found between soil organic carbon content and the different B pools, except for hot water soluble (HWS) B. Correlation coefficients between the B pools and particle size distribution were poor and correlation between carbonates and B pools were insignificant. The findings suggest that in Saskatchewan soils, readily soluble B is only a small proportion of the total B, and the majority of B exists as residual or occluded form. Hot water soluble B appears to be a good method to estimate available B. We found this method rather simple, efficient, and consistent. Key words: Boron fractionation, exchangeable B, extractable B, organically bound B, soluble B

The concentration of soluble polysaccharides in the rumen contents of sheep fed on hay

1970 ◽  
Vol 75 (3) ◽  
pp. 471-478 ◽  
Author(s):  
P. N. Hobson ◽  
J. K. Thompson
Keyword(s):  
Small Proportion ◽  
Water Soluble ◽  
Hot Water ◽  
Acetate Buffer ◽  
Extracellular Water ◽  
Water Fraction ◽  
Iodine Staining ◽  
Feeding Regimes ◽  
Ad Libitum

SUMMARYOn the feeding regimes examined, i.e. hay ad libitum restricted hay and restricted hay with supplementary glucose, the quantities of extracellular water-soluble polysaccharides in rumen liquor were small (3·6–9·0 mg/100 ml) and could have originated from the diet or the saliva as well as from microbes. The polysaccharides extracted with hot water (fraction B) and acetate buffer (fraction C) were also small in amount in the rumen liquor from sheep on any of these diets (less than 56 mg/100 ml) and were composed of rhamnose—containing polysaccharides, starch-like polysaccharides and xylose polymers. Syntheses of these B and C polysaccharides were found with the hay and glucose diet but the quantities involved were small (12·27 mg/100 ml rumen liquor). Degradation of the polysaccharides occurred at 4–6 h after feeding. The consistently high ratios of rhamnose to hexose in the B and C polysaccharides from rumen liquor suggest that these were microbial in origin. Iodine-staining organisms in the rumen liquor were a small proportion of the total and showed no increases after feeding.

scholarly journals Status of macro- and micro-nutrients in soils of Chamoli district of Uttarakhand

2020 ◽  
pp. 361-366
Author(s):  
SAYANTIKA BHATTACHARYA
Keyword(s):  
Organic Carbon ◽  
Carbon Content ◽  
Sandy Loam ◽  
Ammonium Oxalate ◽  
Soil Survey ◽  
Water Soluble ◽  
Hot Water ◽  
Organic Carbon Content ◽  
Positive Correlation ◽  
Extractable P

A GPS based soil survey was conducted in nine blocks of Chamoli district of Uttarakhand (n=300) to evaluate the status of extractable macro- and micro-nutrients and to relate them with general soil properties. Soil texture ranged from sandy loam to clay loam, pH from 4.8 to 8.29, electrical conductivity from 0.170 to 5.431 dSm 1 and organic carbon content from 3.14 to 30.72 g kg 1 soil. Among the macro-nutrients, Olsen’s and Bray’s extractable P varied from 1.41 to 47.20 mg kg 1 soil, neutral normal ammonium acetate extractable K content from 24.82 to 269.1 mg kg 1 soil. Exchangeable Ca and Mg content varied from 20 to 1620 mg kg 1 and 12 to 288 mg kg 1 soil, respectively. The content of 0.15% CaCl2 extractable S content varied from 1.23 to 26.64 mg kg 1 soil. The DTPA extractable Zn, Cu, Fe, Mn content varied from 0.09 to 15.41, 0.08 to 9.03, 3.13 to 84.22 and 1.93 to 54.96 mg kg 1 soil, respectively. Hot water-soluble B content varied from 0.23 to 2.61 mg kg 1 soil while ammonium oxalate (pH 3.3) extractable Mo content varied from 0.18 to 1.36 mg kg 1 soil. Simple correlation showed that soil pH had a significant and positive correlation with soil extractable P, Ca, S, B and Mo but a negative one with extractable Cu, Fe and Mn. Soil EC had a significant and positive correlation with extractable P, K, Mg, S, Fe, B and Mo. Soil organic carbon had a significant and positive correlation with extractable K. On the basis of calculated nutrient indices (N.I.), the soils of Chamoli district were low in soil extractable S, medium in extractable K and Zn, high in organic carbon content, extractable P, Ca, Mg, Cu, Fe, Mn, B and Mo with sporadic cases of Zn, Cu and B deficiency.

Controlled Release of Metformin Hydrochloride I. In vitro Release from Physical Mixture Containing Xanthan Gum as Hydrophilic Rate Retarding Polymer

1970 ◽  
Vol 4 (1) ◽  
Author(s):  
Mashkura Ashrafi ◽  
Jakir Ahmed Chowdhury ◽  
Md Selim Reza
Keyword(s):  
Controlled Release ◽  
Xanthan Gum ◽  
In Vitro Release ◽  
Correlation Coefficients ◽  
High Ratio ◽  
Water Soluble ◽  
Metformin Hydrochloride ◽  
Model Drug ◽  
Very High

Capsules of different formulations were prepared by using a hydrophilic polymer, xanthan gum and a filler Ludipress. Metformin hydrochloride, which is an anti-diabetic agent, was used as a model drug here with the aim to formulate sustained release capsules. In the first 6 formulations, metformin hydrochloride and xanthan gum were used in different ratio. Later, Ludipress was added to the formulations in a percentage of 8% to 41%. The total procedure was carried out by physical mixing of the ingredients and filling in capsule shells of size ‘1’. As metformin hydrochloride is a highly water soluble drug, the dissolution test was done in 250 ml distilled water in a thermal shaker (Memmert) with a shaking speed of 50 rpm at 370C &plusmn 0.50C for 6 hours. After the dissolution, the data were treated with different kinetic models. The results found from the graphs and data show that the formulations follow the Higuchian release pattern as they showed correlation coefficients greater than 0.99 and the sustaining effect of the formulations was very high when the xanthan gum was used in a very high ratio with the drug. It was also investigated that the Ludipress extended the sustaining effect of the formulation to some extent. But after a certain period, Ludipress did not show any significant effect as the pores made by the xanthan gum network were already blocked. It is found here that when the metformin hydrochloride and the xanthan gum ratio was 1:1, showed a high percentage of drug release, i.e. 91.80% of drug was released after 6 hours. But With a xanthan gum and metformin hydrochloride ratio of 6:1, a very slow release of the drug was obtained. Only 66.68% of the drug was released after 6 hours. The percent loading in this case was 14%. Again, when Ludipress was used in high ratio, it was found to retard the release rate more prominently. Key words: Metformin Hydrochloride, Xanthan Gum, Controlled release capsule Dhaka Univ. J. Pharm. Sci. Vol.4(1) 2005 The full text is of this article is available at the Dhaka Univ. J. Pharm. Sci. website

scholarly journals Innovative BPPO Anion Exchange Membranes Formulation Using Diffusion Dialysis-Enhanced Acid Regeneration System

Membranes ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 311
Author(s):  
Muhammad Imran Khan ◽  
Majeda Khraisheh ◽  
Fares AlMomani
Keyword(s):  
Anion Exchange ◽  
Room Temperature ◽  
Feed Solution ◽  
Exchange Capacity ◽  
Anion Exchange Membranes ◽  
Regeneration System ◽  
Waste Streams ◽  
Acid Recovery ◽  
Aqueous Waste ◽  
Diffusion Dialysis

Recycling of acid from aqueous waste streams is crucial not only from the environmental point of view but also for maturing the feasible method (diffusion dialysis). Anion exchange membrane (AEM)–based diffusion dialysis process is one of the beneficial ways to recover acid from aqueous waste streams. In this article, the synthesis of a series of brominated poly (2, 6–dimethyl-1, 4–phenylene oxide) (BPPO)-based anion exchange membranes (AEMs) through quaternization with triphenylphosphine (TPP) were reported for acid recovery via diffusion dialysis process. The successful synthesis of the prepared membranes was confirmed by Fourier transform infrared (FTIR) spectroscopy. The as-synthesized anion exchange membranes represented water uptake (WR) of 44 to 66%, ion exchange capacity of (IEC) of 1.22 to 1.86 mmol/g, and linear swelling ratio (LSR) of 8 to 20%. They exhibited excellent thermal, mechanical, and acid stability. They showed homogeneous morphology. The acid recovery performance of the synthesized AEMs was investigated in a two compartment stack using simulated mixture of HCl and FeCl2 as feed solution at room temperature. For the synthesized anion exchange membranes TPP–43 to TPP–100, the diffusion dialysis coefficient of acid (UH+) was in the range of 6.7 to 26.3 (10−3 m/h) whereas separation factor (S) was in the range of 27 to 49 at 25 °C. Obtained results revealed that diffusion dialysis performance of the synthesized AEMs was higher than the commercial membrane DF–120B (UH+ = 0.004 m/h, S = 24.3) at room temperature. It showed that the prepared AEMs here could be excellent candidates for the diffusion dialysis process.

scholarly journals Transport Characteristics of CJMAED™ Homogeneous Anion Exchange Membranes in Sodium Chloride and Sodium Sulfate Solutions

2021 ◽  
Vol 22 (3) ◽  
pp. 1415
Author(s):  
Veronika Sarapulova ◽  
Natalia Pismenskaya ◽  
Valentina Titorova ◽  
Mikhail Sharafan ◽  
Yaoming Wang ◽  
...  
Keyword(s):  
Ion Exchange ◽  
Anion Exchange ◽  
Volume Fraction ◽  
Exchange Capacity ◽  
Polymer Materials ◽  
Transport Numbers ◽  
Anion Exchange Membranes ◽  
Microheterogeneous Model ◽  
Pass Through ◽  
Pes Membrane

The interplay between the ion exchange capacity, water content and concentration dependences of conductivity, diffusion permeability, and counterion transport numbers (counterion permselectivity) of CJMA-3, CJMA-6 and CJMA-7 (Hefei Chemjoy Polymer Materials Co. Ltd., China) anion-exchange membranes (AEMs) is analyzed using the application of the microheterogeneous model to experimental data. The structure–properties relationship for these membranes is examined when they are bathed by NaCl and Na2SO4 solutions. These results are compared with the characteristics of the well-studied homogenous Neosepta AMX (ASTOM Corporation, Japan) and heterogeneous AMH-PES (Mega a.s., Czech Republic) anion-exchange membranes. It is found that the CJMA-6 membrane has the highest counterion permselectivity (chlorides, sulfates) among the CJMAED series membranes, very close to that of the AMX membrane. The CJMA-3 membrane has the transport characteristics close to the AMH-PES membrane. The CJMA-7 membrane has the lowest exchange capacity and the highest volume fraction of the intergel spaces filled with an equilibrium electroneutral solution. These properties predetermine the lowest counterion transport number in CJMA-7 among other investigated AEMs, which nevertheless does not fall below 0.87 even in 1.0 eq L−1 solutions of NaCl or Na2SO4. One of the reasons for the decrease in the permselectivity of CJMAED membranes is the extended macropores, which are localized at the ion-exchange material/reinforcing cloth boundaries. In relatively concentrated solutions, the electric current prefers to pass through these well-conductive but nonselective macropores rather than the highly selective but low-conductive elements of the gel phase. It is shown that the counterion permselectivity of the CJMA-7 membrane can be significantly improved by coating its surface with a dense homogeneous ion-exchange film.

EXTRACTION OF BORON FROM CSSC REFERENCE SOILS BY HOT WATER, DILUTE CaCl2 AND MANNITOL-CaCl2 SOLUTIONS

1986 ◽  
Vol 66 (2) ◽  
pp. 377-381 ◽  
Author(s):  
P. A. SCHUPPLI
Keyword(s):  
Key Words ◽  
Soil Samples ◽  
Water Soluble ◽  
Hot Water ◽  
Distilled Water ◽  
Background Color ◽  
Color Development ◽  
Reference Soil ◽  
Highly Correlated

Soils were extracted by hot water, dilute CaCl2, and by mannitol-CaCl2 solutions and boron was determined by either azomethine-H or the curcumin method. Results were strongly method dependent; in particular results by the simplest method, mannitol-CaCl2, were generally lower and not highly correlated (r = 0.64) with those by the recommended procedure. This procedure involves extraction with hot distilled H2O (2:1 solution:soil), centrifugation, filtration, color development with azomethine-H and correction for background color. Extractable boron values by this procedure ranged from 0.1 to 1.4 mg kg−1. Background color can be further reduced by the substitution of 0.02 M CaCl2 for distilled water. Key words: CSSC reference soil samples, hot-water-soluble boron

Effect of previous cutting interval and of leaf area remaining after cutting on regrowth of Macroptilium atropurpureum cv. Siratro

1974 ◽  
Vol 14 (68) ◽  
pp. 343 ◽  
Author(s):  
RJ Jones
Keyword(s):  
Leaf Area ◽  
Practical Implication ◽  
Soluble Sugars ◽  
Ground Level ◽  
Fold Increase ◽  
Water Soluble ◽  
Hot Water ◽  
Lag Phase ◽  
Area Index ◽  
Plant Yield

Experiments with Siratro were conducted at Samford, south east Queensland to study the effects of previous cutting and defoliation treatments on regrowth. In the first experiment, swards of Siratro were cut at 7.5 cm above ground level every 4 weeks, every 8 weeks or cut once at 16 weeks during spring and summer. Regrowth of all treatments over ten weeks was measured after varying (by leaf removal) the stubble leaf area index (LAI) of the plots cut every four weeks. Pattern of regrowth yield was similar for all treatments with a pronounced lag phase after cutting. Regrowth yield after 10 weeks differed between treatments and was linearly related (P < 0.01 ) to residual LAI in the stubble at the start of regrowth. In the absence of stubble leaves, plots previously cut at 16 weeks or at 8 weeks yielded marginally more than those cut every 4 weeks. There were no marked treatment differences in gross root morphology other than a two fold increase in stolon rooting for the 16-week treatment. Nitrogen content of the roots (mean 1.38 per cent) was unaffected by treatment, but the per cent hot water soluble sugars were lower for the 16 week defoliation treatment than for the 8-week and the 4-week treatments. In the second experiment individual plants were cut to a uniform stubble every 4 weeks and either 0, 5, or 10 leaves were left. Dry weight of regrowth and stolon development were greatest when most leaves were left. Two thirds of the plants died after six cuttings with complete defoliation but none died when either 5 or 10 leaves were retained. Plant survival was not related to plant yield or degree of stoloniferous development. However, there was a strong correlation between stolon number and plant yield under this intensive cutting regime. The practical implication of the results in the management of Siratro is discussed.

scholarly journals Characteristics of the Water- and Alkali-Soluble Hemicelluloses Fractionated by Sequential Acidification and Graded-Ethanol from Sweet Maize Stems

Molecules ◽  
2019 ◽  
Vol 24 (1) ◽  
pp. 212 ◽  
Author(s):  
Xiaopeng Peng ◽  
Shuangxi Nie ◽  
Xiaoping Li ◽  
Xiong Huang ◽  
Quanzi Li
Keyword(s):  
Potassium Hydroxide ◽  
Ethanol Solution ◽  
Water Soluble ◽  
Hot Water ◽  
Fundamental Information ◽  
Composition And Structure ◽  
Structural Characterizations

Sweet maize stems were treated with hot water and potassium hydroxide to fractionate hemicellulosic polymers. The results showed that the water-soluble hemicelluloses were mainly composed of glucose (27.83%), xylose (27.32%), and galactose (16.81%). In comparison, alkali-soluble hemicelluloses fractionated by acidification and a graded ethanol solution (10%, 20%, 35%, 50%, 65%, and 80%) were mainly composed of xylose (69.73 to 88.62%) and arabinose (5.41 to 16.20%). More highly branched hemicelluloses tended to be precipitated in a higher concentration of ethanol solution, as revealed by the decreasing xylose to arabinose ratio from 16.43 to 4.21. Structural characterizations indicated that alkali-soluble hemicelluloses fractionated from sweet maize stems were mainly arabinoxylans. The results provided fundamental information on hemicelluloses composition and structure and their potential utilization in the fields of biofuels, biochemicals, and biomaterials.

Evaluation of the 3M Dry Medium Culture Plate (Petrifilm™ SM) Method for Determining Numbers of Bacteria in Raw Milk1

1984 ◽  
Vol 47 (10) ◽  
pp. 753-755 ◽  
Author(s):  
R. E. GINN ◽  
V. S. PACKARD ◽  
T. L. FOX
Keyword(s):  
Cold Water ◽  
Correlation Coefficients ◽  
Raw Milk ◽  
Water Soluble ◽  
Gelling Agent ◽  
Plate Count ◽  
Suitable Alternative ◽  
Standard Plate Count ◽  
Standard Plate ◽  
Indicator Dye

The 3M Company has developed a sample-ready system (Petrifilm ™ SM) for enumerating bacteria in milk and other food products. The testing unit consists of Standard Methods culture medium coated onto a base film and overlaid with a second film coated with a cold-water-soluble gelling agent and tetrazolium indicator dye. As such, the system is ready to accept samples of product. A pipette or 0.001-ml plate loop continuous pipetting syringe can be used for applying samples. In this study, both methods of sample addition were used and results compared with those of the Standard Plate Count (SPC) and standard Plate Loop (PL) methods for determining bacteria numbers in raw milk. In total, 108 samples were analyzed in duplicate by each of the four methods. The correlation coefficients (r) between the 3M-SPC and SPC, 3M-PL and PL, 3M-PL and SPC and PL and SPC were 0.946, 0.935, 0.941, and 0.974, respectively. Repeatability, as measured by mean log10 variance for duplicate determinations, was essentially the same for the four methods, and in all instances less than 0.005. The mean log10 differences between the SPC and 3M-SPC, and SPC and 3M-PL were, respectively, −0.177 and −0.168. The preceding statistical criteria suggest the Petrifilm™ SM method to be a suitable alternative to the SPC or the PL procedure.

scholarly journals COMPOSITION, MICROSTRUCTURE AND PROPERTIES OF QUATERNARY CLAYS OF THE PRIKHANKAYSKAYA DEPRESSION (PRIMORYE)

2019 ◽  
Vol 14 (1) ◽  
pp. 20-34
Author(s):  
T. G. RYASHCHENKO ◽  
N. N. UKHOVA ◽  
S. I. SHTELMAKH ◽  
N. I. BELYANINA ◽  
P. S. BELYANIN
Keyword(s):  
Clay Minerals ◽  
Laboratory Data ◽  
Chemical Properties ◽  
Exchange Capacity ◽  
Climatic Conditions ◽  
Water Soluble ◽  
Laboratory Studies ◽  
Microstructural Parameters ◽  
Physical Chemical ◽  
Study Results

The article considers the study results of composition, microstructure and physical-chemical properties of the quaternary clays of the Prikhankayskaya depression in district of the lake Khanka (Primorye) on the example of air-dry samples of geological borehole 45-b in the range of 18–62 m. The objective of research was to obtain new information about the properties of widespread clay sediments in this area using geologic-lithological materials and laboratory data. The schematic geologic-lithological column was composed with the selection of various zones in the quaternary clay sediments section and the border with sediments of the Neogene System. The methodological scheme of laboratory studies of clays was proposed. This scheme includes the determination of chemical and microelement composition, clay minerals, contents of carbonates, water-soluble salts, mobile forms of aluminum oxide, humus, as well as microstructural parameters (method «Microstructure») and some physical-chemical properties. Geochemical coefficients (Kz, CIA, CIW, ICV) determined the degree of chemical maturity of clays and confirmed the results of palynological studies reflecting the fluctuations of the climatic conditions of their formation. For the group of toxic microelements for the first time the special indicator (Zc) was calculated. Which was the criterion for a degree of pollution of the clay sediments section. Clay minerals of the quaternary clays are represented by smectite and hydromica. The clear change in the mineral association was found when passing to the Neogene sediments (kaolinite prevails). The method «Microstructure» revealed the aggregated type of clays microstructure, the domination of the particles of coarse dust fraction among the primary (free) particles and the almost complete absence of the particles of fine-grained sand fraction, the participation of various fractions in the composition of aggregates. The variants of the formation of certain types of aggregates (on sizes) in the fluviolacustrine «khankayskiy» clays are presented. Solid part density, water resistance (soaking time), sedimentation volume, plasticity, relative swelling (samples-pastes) were determined using standard methods for clays. By special methods, the cation exchange capacity was measured and the calculated values of the plasticity index were obtained from forecasting formulas using the yield limit. The proposed methodological scheme of complex laboratory studies of clay sediments can be recommended for problematic geologic-lithological and engineering-geological sections.

Sign in / Sign up

Export Citation Format

Share Document